CRUX RVCGM-80C Bedienungsanleitung


Lesen Sie kostenlos die đź“– deutsche Bedienungsanleitung fĂĽr CRUX RVCGM-80C (8 Seiten) in der Kategorie Nicht kategorisiert. Dieser Bedienungsanleitung war fĂĽr 3 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/8
RVCGM-80C
Rear View Integration Interface for Select
GM Vehicles with CUE, Intellilink and MyLink Systems
R
INTERFACING SOLUTIONS
Sightline
Multi View Integration
Crux Interfacing Solutions • 6860 Canby Ave., Suite 116, Reseda, CA 91335
phone: (818) 609-9299 • fax: (818) 996-8188 • www.cruxinterfacing.com
rev.082718
1 of 8
- Automaîžźcally switches to rear-view when vehicle is put in reverse gear.
- Provides reverse camera input.
- Adds 3 Audio/Video inputs.
- Plug and play installaîžźon.
PRODUCT FEATURES:
PARTS INCLUDED:
RVCGM-80C
Module
Remote Control Power Harness
IR Extension Cable LVDS Cable A/V Cable
Camera Power Harness Push Buîž©on Switch
Crux Interfacing Solutions • 6860 Canby Ave., Suite 116, Reseda, CA 91335
phone: (818) 609-9299 • fax: (818) 996-8188 • www.cruxinterfacing.com
rev.082718
2 of 8
R
INTERFACING SOLUTIONS
Sightline
Multi View Integration
RVCGM-80C
Rear View Integration Interface for Select
GM Vehicles with CUE, Intellilink and MyLink Systems
INSTALLATION DIAGRAM:
AV1
AV2
LVDS
Output
AV3
AV OUT
+12V ACC
GROUND
Fuse Box
Connect to Blue
Mini USB Plug from
HMI Module
Plug to HMI
Module
RGB CABLE
IR REMOTE CABLE
PUSH BUTTON SWITCH
CAMERA POWER
+12V GROUND
DIP SWITCHES
Sig tli e
REAR-VIEW INTEGRATION
RVCGM-80C
24-PIN
POWER PLUGSTATUS LED
24-Pin
Audio/Video
IN/OUT
GM-80C LVDS
T-HARNESS
Crux Interfacing Solutions • 6860 Canby Ave., Suite 116, Reseda, CA 91335
phone: (818) 609-9299 • fax: (818) 996-8188 • www.cruxinterfacing.com
rev.082718
3 of 8
R
INTERFACING SOLUTIONS
Sightline
Multi View Integration
RVCGM-80C
Follow these steps to properly install the interface module. Note that this interface connects to the HMI Module.
Rear View Integration Interface for Select
GM Vehicles with CUE, Intellilink and MyLink Systems
INSTALLATION INSTRUCTIONS:
1. Remove the GLOVE BOX to gain access to the factory HMI module. The HMI module is located in diîś«erent areas
depending on the vehicle model. Below is a list of vehicles and where the HMI module can be located:
Cadillac ATS/CTS = below the glove box
Cadillac SRX = below or behind the glove box
Corveîž©e = driver side kick panel
Once you have located the HMI module, unplug the BLUE LVDS connector. You will need to plug this to the
RVCGM-80C Main Interface Module.
Factory LVDS
Connector
2. Using the provided 24-Pin Power Harness, connect the loose wires on the 24-Pin as menîžźoned below. You can
tap Accessory power from the cigareîž©e lighter (+12V switched) posiîžźon.
NOT ALL LOOSE WIRES ON THE
24-PIN CONNECTOR ARE USED Factory Mini USB (LVDS)
connecîžźons are mostly
located on the MyLink
System box.
RED = Accessory
BLACK = Ground
BLUE = Parking
GRAY = Reverse Input
3. Aer making the connecons on the 24-Pin harness, insert the 24-Pin into the Main Interface module. Make
sure that the connector is properly seated into the module.


Produktspezifikationen

Marke: CRUX
Kategorie: Nicht kategorisiert
Modell: RVCGM-80C

Brauchst du Hilfe?

Wenn Sie Hilfe mit CRUX RVCGM-80C benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Nicht kategorisiert CRUX

Bedienungsanleitung Nicht kategorisiert

Neueste Bedienungsanleitung fĂĽr -Kategorien-