CRUX RNS-VW Bedienungsanleitung


Lesen Sie kostenlos die đź“– deutsche Bedienungsanleitung fĂĽr CRUX RNS-VW (3 Seiten) in der Kategorie Nicht kategorisiert. Dieser Bedienungsanleitung war fĂĽr 7 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/3
RNS-VW
Rear View Integration Interface for Select
Volkswagen Vehicles with MFD3 RNS315 & RNS510 Navigation System
R
INTERFACING SOLUTIONS
Sightline
Multi View Integration
Crux Interfacing Solutions • Chatsworth, CA 91311
phone: (818) 609-9299 • fax: (818) 996-8188 • www.cruxinterfacing.com
rev.0902201 of 3
- Automaîžźcally switches to Rear-view when car is in Reverse mode.
- OBD coder for single acîžźvaîžźon included.
- Plug & Play Installaîžźon.
PRODUCT FEATURES:
PARTS INCLUDED:
RNS-VW Module RNS-VW Harness
Power Down Circuit OBD II Coder
FACTORY
RADIO
12-PIN
(male plug)
26-PIN
(female plug)
NAV
MUTE
SETUP
BAND
MEDIA
PHONE
i
POWER DOWN
CIRCUIT
RED / R E TR R PUTEV RSE IGGE IN
YELLOW / 12V CONSTANT
BLA CK / G DROUN
INTERFACE
RED / 12V POWER
BLACK / GROUND
FR OM REVE E IGHTRS L
USE TO POWER THE CAMERA
CAMERA INPUT
INSTALLATION DIAGRAM:
SPECIAL NOTE:
In the event this unit is to be returned for any reason, the customer must “decode” the radio before
doing so to receive a replacement or refund. See instructions on page 2 on how to decode the radio.
Crux Interfacing Solutions • Chatsworth, CA 91311
phone: (818) 609-9299 • fax: (818) 996-8188 • www.cruxinterfacing.com
rev.0902202 of 3
R
INTERFACING SOLUTIONS
Sightline
Multi View Integration
RNS-VW
Rear View Integration Interface for Select
Volkswagen Vehicles with MFD3/RNS315/RNS510 Navigation System
INSTALLATION INSTRUCTIONS:
CODING THE RADIO FOR A BACKUP CAMERA
1. Locate the vehicle’s OBD II port usually located under the steering column.
2. Enter the vehicle and CLOSE ALL DOORS.
3. Turn the key to the ON posiîžźon.
4. Plug in the OBD coder from the RNS-VW kit to the ODB II port.
5. Wait for the OBD coder to nish coding the radio and give a solid GREEN LED. (See chart below)
6. The radio may ash a few me during this process. It can take around 5 seconds to complete the
coding process. If an error occurs, retry the coding procedure.
7. Aer the coding is complete, disconnet the OBD coder and store in a safe place. This OBD coder is
VIN specic and will only work on this vehicle.
In order for the vehicle to recognize the camera and engage it when in reverse gear, the vehicle must be
coded. Use the ODB II coder included in the RNS-VW kit.
Reading the LED color paîž©ern:
Flashing LED Coding Vehicle
Solid Green LED Acîžźvated
Solid Red LED Deacîžźvated
Solid Red & Green LED Error
INTERFACE
GREEN LED
RED LED
8-PIN
(male plug) LED
(indicator)
OBD CODER
DECODING THE RADIO
To decode the radio, repeat the steps above.
Crux Interfacing Solutions • Chatsworth, CA 91311
phone: (818) 609-9299 • fax: (818) 996-8188 • www.cruxinterfacing.com
rev.0902203 of 3
R
INTERFACING SOLUTIONS
Sightline
Multi View Integration
RNS-VW
Rear View Integration Interface for Select
Volkswagen Vehicles with MFD3/RNS315/RNS510 Navigation System
VEHICLE APPLICATIONS:
MFD3 RNS315 Navigaîžźon Radios
2012 – 2015 Beetle
2011 – 2014 CC
2011 – 2014 Golf
2011 – 2014 GTI
2011 – 2014 Jea
2011 – 2014 Jea SportWagen
2012 – 2014 Passat*
2011 – 2014 Tiguan
USING THE POWER DOWN CIRCUIT
The power down circuit is designed to extend the life of the camera. NOTE: Green wire is only used to power the
camera and module.
1. Tap the GREEN wire to 2 Red wires, one coming from the camera cable and one from the module.
2. Locate the reverse light trigger wire in the vehicle and connect it to the RED wire. This will trigger the 12V input.
3. Connect the YELLOW wire to any available 12V constant source in the car.
4. Connect the BLACK wire to a good chassis ground source.
MFD3 RNS510 Navigaîžźon Radios**
2007 – 2009 Eos
2007 – 2009 Golf
2007 – 2009 Passat
2008 – 2009 Tiguan
2008 – 2010 Touareg
VOLKSWAGEN
IMPORTANT NOTES:
*On the 2012 Passat radio (RNS315), the rear-view camera will start to funcon aer the car goes to sleep/power down mode. Aer
the coding process, turn key oîś« and remove key. Open and close doors then lock the car. Wait for 3 minutes. Start the car and put
the gear in reverse and conrm that the camera image shows on the screen.
**Certain U.S. version RNS-510 Radios (late 2009-up) may not have camera input capability. Please verify feature prior to purchase.
MFD3 / RNS315 Radio RNS510 Radio


Produktspezifikationen

Marke: CRUX
Kategorie: Nicht kategorisiert
Modell: RNS-VW

Brauchst du Hilfe?

Wenn Sie Hilfe mit CRUX RNS-VW benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Nicht kategorisiert CRUX

Bedienungsanleitung Nicht kategorisiert

Neueste Bedienungsanleitung fĂĽr -Kategorien-