BSS Audio Soundweb 9000 Bedienungsanleitung


Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für BSS Audio Soundweb 9000 (6 Seiten) in der Kategorie Nicht kategorisiert. Dieser Bedienungsanleitung war für 12 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/6
105
SoundwebTM
SoundwebSoundweb
SoundwebSoundweb
SoundwebTMTM
TMTMTM 9000 9000
9000 9000
9000
Installation Guide
106
SoundwebTM
Regulatory Information
An example of this equipment has been tested and found to comply with the following European
and international Standards for Electromagnetic Compatibility and Electrical Safety:
Radiated Emissions (EU): EN55022B (1994)
Immunity (EU): EN50082/1 (1992) RF Immunity, Fast
Transients ESD
Mains Disturbance (EU): EN61000/3/2 (1995)
Electrical Safety (EU): EN60065 (1993)
Radiated Emissions (USA): FCC part 15 Class B
Electrical safety (USA): UL6500
Important safety information - read and follow
Do not remove covers. No user serviceable parts inside, refer servicing to qualified service
personnel. For continued compliance with international EMC regulations, it is important that all
cables be screened, and connected as follows: Control cable screens to the ground screws
adjacent to the connector. Network cables should be of type CAT.5. WARNING: This equipment
must be earthed. It should not be necessary to remove any protective earth or signal cable shield
connections to prevent ground loops. Any such disconnections are outside the recommended
practice of BSS Audio, and will render the EMC or safety certificate void. Do not defeat the safety
purpose of the polarised/grounding plug. A polarised plug has 2 blades, one wider than the other. A
grounding type plug has 2 blades, and a third grounding prong. The third prong is provided for
your safety. When the provided plug does not fit an electrical outlet, consult a qualified electrician.
Mechanical Installation
If the unit is likely to undergo extreme vibration through extensive road trucking and touring, the
unit must be supported at the rear and/or sides to lessen the stress on the front mounting flange.
The necessary support can generally be bought ready-built as a rack tray, or the 9000 unit can be
mounted between other units. Damage caused by insufficient support is not covered by the
warranty. To prevent cosmetic damage to the front panel finish, use protective plastic cups under
the rack mounting bolts.
No-user servicable parts
compartment warning.
107
SoundwebTM
Front panel LED functions
Network monitoringNetwork monitoring
Network monitoringNetwork monitoringNetwork monitoring
Each node has 3 LED indicators showing:
NetworkNetwork
NetworkNetwork
Network
MasterMaster
MasterMasterMaster
Flashing - The network is initialising. If it does not cease to flash, there is a cabling fault -
either a double ring error or a problem with one of the cable connectors.
Steady - This node has become the hub master for this unit. It is either directly connected
to the network maste , or connected to a ring which contains the network maste .r r
Off - This node is to the master'sclienting clock.
SyncSyncSyncSyncSync
Steady - This indicates the presence of a valid network connection on this node.
Flashing - There is a problem with the incoming network signal - possibly the maximum
cable length has been exceeded.
Activity
Activity
ActivityActivity
Activity
Flashing - This LED indicates data transfe . The flashing is not regula , but dependant onr r
the rate of transfe .r
The node 1 light also indicates RS232 serial messaging in the same manne .r
DSP ClipDSP Clip
DSP ClipDSP Clip
DSP Clip
Illuminated - Indicates that the signal is clipping internally.
PowerPowerPowerPowerPower
Steady - This indicates that the power supply is functioning.
RX - 5
GND - 4
TX - 3
RTS - 1
CTS - 2
Front panel details
RS232RS232
RS232RS232RS232
Used to connect one of the 9000 units in the network to a controller PC, which can then
communicate with any device on the network. The pin out is:
Control cable wiring details
All control connections to the 9000 are via Klippon pluggable terminal block connectors
(also known as BL, Phoenix or Combicon). 6-way female Klippon connectors are
supplied for making these connections.


Produktspezifikationen

Marke: BSS Audio
Kategorie: Nicht kategorisiert
Modell: Soundweb 9000

Brauchst du Hilfe?

Wenn Sie Hilfe mit BSS Audio Soundweb 9000 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Nicht kategorisiert BSS Audio

Bedienungsanleitung Nicht kategorisiert

Neueste Bedienungsanleitung für -Kategorien-