Yakima RaptorAero Bedienungsanleitung

Yakima Fahrradträger RaptorAero

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Yakima RaptorAero (18 Seiten) in der Kategorie Fahrradträger. Dieser Bedienungsanleitung war für 10 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/18
1033402A-1/18
RaptorAero
Part #1033402 Rev.A
THREADED PLUG (1)
GUIDE PLUG (1)
CLIP (1)
WHEEL TRAY (1)
(JAW)
RED
KNOB
(1)
SPRING (1)
SHORT CARRIAGE
BOLT (1)
WASHER (1)
LOCK WASHER (1)
WING NUT (1)
WHEEL
STRAP (2)
WHEEL TRAY
END CAP (2)
WRENCH (1)
SHORT WHEEL
TRAY BOLT (1)
LONG CARRIAGE
BOLT (2)
SHORT HEX BOLT,
FOR SMALL BAIL (3)
LONG HEX BOLT,
FOR LARGE BAIL (3)
BARREL SLEEVE (3)
SPACER (3)
BACKBONE (3)
NUT (3)
SET OF PADS (3)
SMALL BAIL (3),
MARKED “A”
LARGE BAIL (3),
MARKED “B”
THUMB-WHEEL (3)
(HOOP ASSEMBLY)
(BASEPLATE)
IMPORTANT WARNING: IT IS CRITICAL THAT ALL YAKIMA RACKS AND ACCESSORIES BE PROPERLY AND SECURELY
ATTACHED TO YOUR VEHICLE. IMPROPER ATTACHMENT COULD RESULT IN AN AUTOMOBILE ACCIDENT, AND COULD
CAUSE SERIOUS BODILY INJURY OR DEATH TO YOU OR TO OTHERS. YOU ARE RESPONSIBLE FOR SECURING THE RACKS
AND ACCESSORIES TO YOUR CAR, CHECKING THE ATTACHMENTS PRIOR TO USE, AND PERIODICALLY INSPECTING THE
PRODUCTS FOR ADJUSTMENT, WEAR, AND DAMAGE. THEREFORE, YOU MUST READ AND UNDERSTAND ALL OF THE INSTRUCTIONS
AND CAUTIONS SUPPLIED WITH YOUR YAKIMA PRODUCT PRIOR TO INSTALLATION OR USE. IF YOU DO NOT UNDERSTAND ALL
OF THE INSTRUCTIONS AND CAUTIONS, OR IF YOU HAVE NO MECHANICAL EXPERIENCE AND ARE NOT THOROUGHLY FAMILIAR
WITH THE INSTALLATION PROCEDURES, YOU SHOULD HAVE THE PRODUCT INSTALLED BY A PROFESSIONAL INSTALLER SUCH AS
A QUALIFIED GARAGE OR AUTO BODY SHOP.
1 or 2 bikes .......... 16” min. — 38” max.
MORE THAN 2 BIKES ON ROUND OR SQUARE BARS ONLY:
3+ bikes .......... 18” min. — 38” max.
ELONGATED KEY (2)
SNAP AROUND (3)
BASEPLATE BOLT (2)
WHEELTRAY
BOLT (1)
HEX KEY (1)
FACTORY BARS
ATTACHMENT HARDWARE
(UNIVERSAL MIGHTY MOUNTS)
(UNIVERSAL MIGHTY MOUNTS)
Crossbar-spread
requirements:
(DISTANCE BETWEEN TOWERS)
faCtory bar weight limits
2 bikes = MAXIMUM LOAD
EACH BIKE = 30 lbs./14 kg
(do not exceed rack weight limit)
ROUND AND SQUARE BARS
ATTACHMENT HARDWARE
1033402A-2/18
Always use the short bolt with small bail — and long bolt with large bail.
Press a pad into the
smaller bail (marked “A”).
• Close and compress the
mount around the bar.
• Insert a short hex bolt into
the hex opening in the barrel
sleeve, and insert into mount.
Press a pad into the backbone.
(You may need to rotate the pad
to fit correctly.)
INSTALL PADS TO ONE SET OF MOUNTS.
Place the mount onto the bar, opening toward the front of the car.
ATTACH SMALL BAIL TO
BACKBONE.
IF THE BOLT DOES NOT EXTEND,
remove the bail, and set the end
into the lower slot.
Bolt threads
MUST extend
below the
closed bail.
If the bolt threads still do not
extend below the closed bail:
Always install the
pad on the bail for
this fitting process.
Attach the thumb-wheel:
If there is any looseness, or the mounts can slide
on the bar, follow the fitting process again.
FACTORY
CROSSBARS ONLY:
Start here to find the Universal MightyMount
parts that fit your crossbars.
Remove the fitted mount from the bar.
BAIL
BACKBONE
Repeat the fitting process
until the MightyMount
conforms to the size of your
crossbars when the wheel
is tightened.
• Assemble the remaining mounts, and
carefully set them aside.
• Do not discard the unused parts (you
may use them on future vehicles).
• CONTINUE TO STEP 9.
• Use the larger bail (marked “B”)
with longer bolt.
• Repeat step 2 and 3.
ROUND OR SQUARE
CROSSBARS,
continue to step 7.
Use the upper hinge slot
on the backbone.
1033402A-3/18
INSTALL
RED KNOB
• Choose access from
passenger or driver side.
• Red knob should face you
when the Raptor Aero is
attached to wheel tray.
jAwS
guide
Plug
Red knob
thReAded
Plug
• Place the GUIDE PLUG into the
hole on one side of the jaws.
• Slide the red knob‘s bolt threads
through the guide plug.
guide Plug
• Insert the Threaded Plug into
the other hole.
• Place spring between guide
plug and threaded plug.
• Slide knob through spring
and into threaded plug.
thReAded
Plug
Turn the red knob
clockwise to engage
the threaded plug.
SPRing
Tighten knob completely until
threaded end is exposed.
Slide the “E”clip into groove on end.
A coin or a key may
provide added leverage.
Open red knob
completely.
SKS® Lock Cores are optional.
To install SKS® Lock Cores, refer to lock
instructions.
NOTE: If not using lock,
leave plug in place.
ROUND OR SQUARE BARS: Install the SnapArounds.
DO NOT INSTALL Universal MightyMounts on round or square bars!
Remove the tabs with
scissors or pliers. Attach 2 SnapArounds
on the front crossbar,
and 1 on the rear
crossbar.
JAW ASSEMBLY (Round, Square, or Factory Crossbars)
square bars onlY : round and square bars :
Loosen the tabs by
bending them repeatedly.


Produktspezifikationen

Marke: Yakima
Kategorie: Fahrradträger
Modell: RaptorAero

Brauchst du Hilfe?

Wenn Sie Hilfe mit Yakima RaptorAero benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Fahrradträger Yakima

Bedienungsanleitung Fahrradträger

Neueste Bedienungsanleitung für -Kategorien-