Yakima HoldUp +2 Bedienungsanleitung


Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Yakima HoldUp +2 (21 Seiten) in der Kategorie Fahrradträger. Dieser Bedienungsanleitung war für 10 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/21
1034431G-1/21
IMPORTANT WARNING
IT IS CRITICAL THAT ALL YAKIMA RACKS AND ACCESSORIES BE PROPERLY AND SECURELY ATTACHED TO YOUR VEHICLE. IMPROPER
ATTACHMENT COULD RESULT IN AN AUTOMOBILE ACCIDENT, AND COULD CAUSE SERIOUS BODILY INJURY OR DEATH TO YOU OR
TO OTHERS. YOU ARE RESPONSIBLE FOR SECURING THE RACKS AND ACCESSORIES TO YOUR CAR, CHECKING THE ATTACHMENTS
PRIOR TO USE, AND PERIODICALLY INSPECTING THE PRODUCTS FOR ADJUSTMENT, WEAR, AND DAMAGE. THEREFORE, YOU
MUST READ AND UNDERSTAND ALL OF THE INSTRUCTIONS AND CAUTIONS SUPPLIED WITH YOUR YAKIMA PRODUCT PRIOR TO INSTALLATION
OR USE. IF YOU DO NOT UNDERSTAND ALL OF THE INSTRUCTIONS AND CAUTIONS, OR IF YOU HAVE NO MECHANICAL EXPERIENCE AND ARE NOT
THOROUGHLY FAMILIAR WITH THE INSTALLATION PROCEDURES, YOU SHOULD HAVE THE PRODUCT INSTALLED BY A PROFESSIONAL INSTALLER.
SAFETY CLIP (1X)
BASE (1X)
WRENCH (1X)
REAR WHEEL TRAY
ASSEMBLY (1X)
FRONT WHEEL TRAY
ASSEMBLY (1X)
BOLT (1X)
LOCK WASHER (1X)
INsTAll ThIs
PROducT ON 2"
hITch veRsION Of
The hOlduP
PIN (1X)
PLUG (1X)
KEY (2X)
For Your
Safety
Warranty
Registration
on-line
YAKIMA.com
Safety Kit included:
See additional
instructions for
installation.
HEX WRENCH (1X)
1034431G-2/21
ReMOve eNd cAP
fROM hOlduP.
Using a flathead screwdriver, remove
the end cap from the HoldUp.
INseRT Plus2 BAse INTO hOlduP.
Insert the Plus2
base into the
HoldUp tube,
aligning holes.
Align
INsTAll MAIN BOlT.
• Insert bolt,
and lock-
washer in
order shown.
• Tighten with
adjustable
wrench.
ROTATe TO uPRIGhT POsITION.
• Squeeze knob to release lock.
• Pull spring pin to release base.
• Lift frame.
• Release spring pin. Pin should snap into place
and lock.
75 ft-lbs.
ReMOve fAsTeNeRs.
The fasteners are installed in the trays for shipping
purposes. Remove them to prepare for assembly.
1034431G-3/21
ATTAch fIRsT TRAY TO BAse.
LOWER TRAY:
IMPORTANT: Wheel strap is
to your right, and pivot arm is
to your left.
wheel strap
•Alignholesintraytobecenteredinslotsonbase.
•Installbolt,lock-washer,andwasher,inordershown.
•Fingertightenallfourbolts.
•Tightenwithsuppliedwrench.
pivot arm
17 ft-lbs.
ATTAch secONd TRAY TO BAse.
UPPER TRAY:
IMPORTANT:
Wheel strap is
to your left, and
pivot arm is to
your right.
pivot arm
wheel strap
17 ft-lbs.
•Alignholesintraytobecenteredinslotsonbase.
•Installbolt,lock-washer,andwasher,inordershown.
•Fingertightenallfourbolts.
•Tightenwithsuppliedwrench.


Produktspezifikationen

Marke: Yakima
Kategorie: Fahrradträger
Modell: HoldUp +2

Brauchst du Hilfe?

Wenn Sie Hilfe mit Yakima HoldUp +2 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Fahrradträger Yakima

Bedienungsanleitung Fahrradträger

Neueste Bedienungsanleitung für -Kategorien-