Yakima HoldUp Bedienungsanleitung


Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Yakima HoldUp (21 Seiten) in der Kategorie Fahrradträger. Dieser Bedienungsanleitung war für 20 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/21
1034426J-1/21
SAFETY CLIP (1X)
WRENCH (1X)
REAR WHEEL TRAY
ASSEMBLY (1X)
FRONT WHEEL TRAY
ASSEMBLY (1X)
HITCH BOLT (1X)
1 1/4" BASE (1X)
(1 1/4" HOLDUP ONLY)
2" BASE (1X)
(2" HOLDUP ONLY)
LOCK WASHER (1X)
KEY (2X)
HEX WRENCH (1X)
HITCHLOCK (1X)
For Your
Safety
Warranty
Registration
on-line
YAKIMA.com
 Install This product on 2" OR 1¼" hitch
receivers ONLY.
 Do not use with hitch-extenders or with
1 ¼” hitch adapters.
 Do not install on trailers, campers, or RVs.
 Do not install if spare tire causes
interference with bikes, or folded carrier.
 Not for use on bikes with front fenders.
In addition, some undersized receivers may
not accept this product. If you do not know the
capabilities of your hitch receiver, consult an
automotive professional.
IMPORTANT WARNING
IT IS CRITICAL THAT ALL YAKIMA RACKS AND ACCESSORIES BE PROPERLY AND SECURELY ATTACHED TO YOUR VEHICLE. IMPROPER
ATTACHMENT COULD RESULT IN AN AUTOMOBILE ACCIDENT, AND COULD CAUSE SERIOUS BODILY INJURY OR DEATH TO YOU OR
TO OTHERS. YOU ARE RESPONSIBLE FOR SECURING THE RACKS AND ACCESSORIES TO YOUR CAR, CHECKING THE ATTACHMENTS
PRIOR TO USE, AND PERIODICALLY INSPECTING THE PRODUCTS FOR ADJUSTMENT, WEAR, AND DAMAGE. THEREFORE, YOU
MUST READ AND UNDERSTAND ALL OF THE INSTRUCTIONS AND CAUTIONS SUPPLIED WITH YOUR YAKIMA PRODUCT PRIOR TO INSTALLATION
OR USE. IF YOU DO NOT UNDERSTAND ALL OF THE INSTRUCTIONS AND CAUTIONS, OR IF YOU HAVE NO MECHANICAL EXPERIENCE AND ARE NOT
THOROUGHLY FAMILIAR WITH THE INSTALLATION PROCEDURES, YOU SHOULD HAVE THE PRODUCT INSTALLED BY A PROFESSIONAL INSTALLER.
1034426J-2/21
INSERT BASE INTO
HITCH RECEIVER.
The holes in
the base must
align to the
holes in the
hitch receiver.
FASTEN HITCH BOLT.
 Insert hitch bolt and lock washer, from RIGHT TO LEFT.
 Tighten with wrench.
REMOVE FASTENERS.
The fasteners are installed in the trays
for shipping purposes. Remove them to
prepare for assembly.
SECURE HITCH
BOLT WITH
SAFETY CLIP
AND INSTALL
HITCHLOCK.
ROTATE BASE TO
UP POSITION.
 Squeeze knob to release lock.
 Pull spring pin to release base.
 Lift frame.
 Release spring pin. Pin should
snap into place and lock.
1 1/4" - 75 ft-lbs.
2" - 100 ft-lbs.
1034426J-3/21
ATTACH FIRST TRAY TO BASE.
LOWER TRAY:
IMPORTANT: Wheel strap
is to your right, and pivot
arm is to your left.
wheel strap
pivot arm
ATTACH SECOND TRAY TO BASE.
pivot arm
wheel strap
 Align holes in tray to be centered in slots on base.
 Insert bolt, washer, and lock-washer, in order shown.
 Finger tighten all four bolts.
 Tighten with supplied wrench.
 Align holes in tray to be centered in slots on base.
 Install bolt, lock-washer, and washer, in order shown.
 Finger tighten all four bolts.
 Tighten with supplied wrench.
UPPER TRAY:
IMPORTANT: Wheel
strap is to your left, and
pivot arm is to your right.
17 ft-lbs.
17 ft-lbs.


Produktspezifikationen

Marke: Yakima
Kategorie: Fahrradträger
Modell: HoldUp

Brauchst du Hilfe?

Wenn Sie Hilfe mit Yakima HoldUp benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Fahrradträger Yakima

Bedienungsanleitung Fahrradträger

Neueste Bedienungsanleitung für -Kategorien-