WHALE Smartbail Bedienungsanleitung


Lesen Sie kostenlos die đź“– deutsche Bedienungsanleitung fĂĽr WHALE Smartbail (32 Seiten) in der Kategorie Nicht kategorisiert. Dieser Bedienungsanleitung war fĂĽr 13 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/32
Model Number BP5012 Smartbail with 1” and 1 1/ ” port option2(retail packed)
Model Number BP5010B Smartbail with 1” Ports (bulk packed)
Model Number BP5021B Smartbail with 1 1/2” Ports (bulk packed)
Installation Guidelines for:
Smartbail Manual
Bilge Pump
This booklet should be read before installation
Please ensure all relevant personnel read the points listed below before installation of the pump
and this is passed on to the end user.
The Whale Smartbail bilge pump is designed to pump standing water when installed through the
bulkhead (see fig.1 below). Output capacity depends on installation conditions and pumping rate.
WARNING: Capacity may not be sufficient to cope with a rapid influx of water.
With all applications it is important that a system of safe working practice is applied to installation,
use and maintenance.
If this pump is intended for use for any other purpose outside of the stated guidelines or with any
other liquid, it is the user's responsibility to ensure that the pump is suitable for the intended use,
and in particular, that the materials are fully compatible with the liquids to be used.
1. Ensure that there is enough room behind the bulkhead for full depth of the pump
when installed. This must include space for inlet and outlet hoses. (See Fig. 2 for
maximum dimensions).
2. Ensure that enough space is available when the pump is installed in order to
operate it with the pump handle fully open. (See fig.3 for recommended
mounting positions).
Application
Before Installation
Fig.1 Typical
Installation
Fig.2 Maximum
Dimensions
Outside Boat
Combined
head and
lift less than
3m
Skin Fitting
Bulkhead
Smartbail
Strum boxes
Top entry - SB5865
Side entry - SB4222
1. Select a suitable flat location on the bulkhead and cut out a circular hole diameter
140mm (5½").
2. Place pump through hole and push into position. Either pushing up or down depending
on mounting orientation (see fig 4a and b).
3. Ensure that the mounting wedge is fully engaged with the bulkhead.
4. Open handle and mark the position of the 4 fixing screw holes on the bulkhead
(see fig.5). – The pump installed using 4 screws.Note must be
5. Remove pump and drill 4 holes at these marked positions. See table below for
recommended screw holes and sizes:
6. Place pump in position and attach to bulkhead using 4 self tapping screws.
Mounting
Pilot Drill Hole Self-tapping Screw
Diameter 3.5 mm Diameter 5 mm
Fig.3 Recommended
Mounting Positions
Fig.4 Mounting Pump
With Wedge
Fig.6
Fig.5 View Of Mounting
Positions
(Ommiting The Handle)
Screw
Holes
Holding
Screws
Handle
Hinge
Mounting wedge
Ensure pushed fully in
this direction
Fig 4a Handle down position Fig 4b Handle position


Produktspezifikationen

Marke: WHALE
Kategorie: Nicht kategorisiert
Modell: Smartbail

Brauchst du Hilfe?

Wenn Sie Hilfe mit WHALE Smartbail benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Nicht kategorisiert WHALE

Bedienungsanleitung Nicht kategorisiert

Neueste Bedienungsanleitung fĂĽr -Kategorien-