Tripp Lite PDUMH15NET2LX Bedienungsanleitung

Tripp Lite Anbaustein PDUMH15NET2LX

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Tripp Lite PDUMH15NET2LX (24 Seiten) in der Kategorie Anbaustein. Dieser Bedienungsanleitung war für 32 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF

Seite 1/24

Owner’s Manual

PDUMH15NET2LX/PDUMH20NET2LX

Switched Rack PDU

120V, 50/60 Hz AC Input and Output

(AG-0091, AG-0092)

Important Safety Instructions 2

Installation 3

Features 5

Configuration and Operation 7

Technical Support 7

Warranty and Product Registration 8

Español 9

Français 17

PROTECT YOUR INVESTMENT!

and ultimate peace of mind.

You could also win an

ISOBAR6ULTRA surge protector—

a $100 value!

www.tripplite.com/warranty

1111 W. 35th Street, Chicago, IL 60609 USA • www.tripplite.com/support

17-02-374-9336CB.indb 1 6/2/2017 2:14:57 PM

Important Safety Instructions

SAVE THESE INSTRUCTIONS

This manual contains instructions and warnings that should be

followed during the installation, operation, and storage of this

product. Failure to heed these instructions and warnings may

affect the product warranty.

• The PDU provides the convenience of multiple outlets, but DOES NOT provide surge

or line noise protection for connected equipment.

• The PDU is designed for indoor use only, in a controlled environment, away from

excess moisture, temperature extremes, conductive contaminants, dust or direct

sunlight.

• Keep indoor ambient temperature between 32°F and 122°F (0°C and 50°C).

• The PDU must be installed by a qualified technician only.

• Do not attempt to mount the PDU to an insecure or unstable surface.

• Install in accordance with National Electrical Code standards. Be sure to use the

proper overcurrent protection for the installation, in accordance with the plug/

equipment rating.

• Connect the PDU to an outlet that is in accordance with your local building codes

and that is adequately protected against excess currents, short circuits and earth

faults.

• The electrical outlets supplying power to the equipment should be installed near the

equipment and easily accessible.

• Do not connect the PDU to an ungrounded outlet or to extension cords or adapters

that eliminate the connection to ground.

• Be sure to provide a local disconnect device on any models that are permanently

installed without a plug that is easily accessible.

• Never attempt to install electrical equipment during a thunderstorm.

• Individual equipment connected to the PDU should not draw more current than the

individual PDU’s outlet’s rating.

• The total load connected to the PDU must not exceed the maximum load rating for

the PDU.

• Do not attempt to modify the PDU, input plugs or power cables.

• Do not drill into or attempt to open any part of the PDU housing. There are no user-

serviceable parts inside.

• Do not attempt to use the PDU if any part of it becomes damaged.

• Use of this equipment in life support applications where failure of this equipment

can reasonably be expected to cause the failure of the life support equipment or to

significantly affect its safety or effectiveness is not recommended.

17-02-374-9336CB.indb 2 6/2/2017 2:14:57 PM

1-1

1-2

1-3

1-4

Installation

Mounting the PDU

The PDU supports four primary mounting configurations: 1U Rack, 0U Rack (Vertical),

Wall and Under-Counter.

Note: Regardless of configuration, the user must determine the fitness of hardware and procedures before

mounting. The PDU and included hardware are designed for common rack and rack enclosure types and may

not be appropriate for all applications. Exact mounting configurations may vary. Screws for attaching the

mounting brackets and cord retention shelf to the PDU are included. Use only the screws supplied by the

manufacturer or their exact equivalent (#6-32, 3/16" flat head).

1-1 1U Rack Mounting: Use 4 screws

A to attach each of the 2

mounting brackets B to the PDU

as shown. Mount the PDU in the

rack by inserting 4 user-supplied

screws C through the mounting

brackets B and into the mounting

holes of the rack rails.

1-2 0U Rack Mounting: Use 4 screws

A to attach each of the 2

mounting brackets B to the PDU

as shown. Mount the PDU

vertically by inserting 2 or more

user-supplied screws C through

the mounting brackets B and into

mounting points in the rack or

rack enclosure.

1-3 Wall Mounting: Use 4 screws A

to attach each of the 2 mounting

brackets B to the PDU as shown.

Mount the PDU to the wall by

inserting 2 or more user-supplied

screws C through the mounting

brackets B and into secure

mounting points.

1-4 Under-Counter Mounting: Use 4

screws A to attach each of the 2

mounting brackets B to the PDU

as shown. Mount the PDU under

the counter by inserting 2 or more

user-supplied screws C through

the mounting brackets B and into

secure mounting points.

17-02-374-9336CB.indb 3 6/2/2017 2:15:00 PM

Produktspezifikationen

Marke:	Tripp Lite
Kategorie:	Anbaustein
Modell:	PDUMH15NET2LX
Breite:	444.5 mm
Tiefe:	108 mm
Gewicht:	2360 g
Produktfarbe:	Schwarz
Höhe:	44.4 mm
Stecker:	NEMA 5–15P
AC Eingangsfrequenz:	50 - 60 Hz
Relative Luftfeuchtigkeit in Betrieb:	5 - 95 %
Verpackungsbreite:	300 mm
Verpackungstiefe:	519.9 mm
Verpackungshöhe:	54.1 mm
Paketgewicht:	3140 g
Montage:	Horizontal
Unterstützte Netzwerkprotokolle:	IPv4, IPv6, HTTP, HTTPS, SMTP, SNMPv1, SNMPv2, SNMPv3, telnet, SSH, FTP, DHCP, NTP
Zertifizierung:	UL 60950-1 (USA). CAN/CSA-C22.2 NO. 60950-1 (Canada), Class A Part 15 (Emissions), NOM\n(Mexico), TAA Compliant
Display:	LCD
Ursprungsland:	Taiwan
Typ:	Einphasig
Kabellänge:	3.66 m
Betriebsanleitung:	Ja
Gehäusematerial:	Metall
LED-Anzeigen:	Ja
Temperaturbereich bei Lagerung:	-15 - 50 °C
Ein-/Ausschalter:	Ja
Anzahl Produkte pro Versandkarton:	1 Stück(e)
Abmessungen (BxTxH):	444 x 108 x 44.4 mm
Nachhaltigkeitszertifikate:	RoHS
Verpackungsabmessungen (BxTxH):	300 x 520 x 54 mm
Max. Leistung:	1520 W
Höhe bei Betrieb:	0 - 3000 m
Temperatur Betriebsumgebung:	5 - 122 °F
Anzahl der AC-Ausgänge:	8 AC-Ausgänge
AC-Steckertypen:	NEMA 5–15R
Stromstärke (maximal):	15 A
Nominale Eingang Spannung:	100-127 V
Nominale Ausgang Spannung:	100-127 V
Rack-Kapazität:	1U
PDU-Typen:	Geändert
Ausgabekontrolle:	Lock-out, Recycle, Turn off, Turn on