Tandberg Data StorageLibrary T40+ Bedienungsanleitung

Tandberg Data Nicht kategorisiert StorageLibrary T40+

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Tandberg Data StorageLibrary T40+ (4 Seiten) in der Kategorie Nicht kategorisiert. Dieser Bedienungsanleitung war für 6 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/4
Quick Installation Steps
For more information and complete step-by-step instructions, please refer to the StorageLibrary T40+ Series
Installation and User Guide available at www.tandbergdata.com .
Warning Although the StorageLibrary T40+ may be lifted by one person when drives, â„¢
power supply, and magazines are removed, for your protection and safety, we
recommend that two people lift the StorageLibraryâ„¢ T40+. All-inclusive library
weight = 38 kg / 84 lbs (2 FH drives). Empty library weight = 23.6 kg / 52 lbs (not
including drives, magazines or power supply).
Caution Please ensure the StorageLibrary T40+ is mounted in the rack before you remove
the transport screws. The transport locking screws must be removed before the
StorageLibrary T40+ can operate normally.
When following the steps below, please refer to the corresponding numbers and letters on the illustrations.
1. Please refer to the StorageLibrary T40+ Series Pass-Thru Installation Manual for instructions of how to
install the unit. To insert the StorageLibrary T40+ onto the rack-rails, please request help of another
person.
2. Before removing the locking screws, power-on the unit. The StorageLibrary T40+ will automatically eject
the magazines if the transport locking screws are mounted. Remove all magazines, remove the four
transport locking screws, and mount the rack mount ears. Re-insert the magazines.
3. Install SCSI, SAS or Fibre Channel cables.
SCSI installation:
Power-off the unit and the host system before plugging in the SCSI cables. When using more than two
SCSI drives, please refer to the StorageLibrary T40+ Series Installation and User Guide for installation
requirements.
a. Connect a SCSI cable from the host to the
1st drive (bottom SCSI connector).
b. Connect a SCSI jumper cable from 1st drive
(top SCSI connector) to the 2nd drive
(bottom SCSI connector). If required repeat
this step for all drive within the tape library.
c. Terminate the last device on the SCSI bus
using the correct SCSI terminator.
NOTE: The maximum SCSI bus length must NOT exceed 9 meters / 30 feet. Please ensure SCSI cables
and teminators are securely fitted using thumbscrews.
SAS installation:
If your library includes tape drives with SAS
interface, connect a SAS cable to each tape
drive separately and connect other end of the
SAS cable to the host.
2
FC installation:
If your library includes tape drives with FC
interface, connect a FC cable to each tape
drive separately and connect other end of the
FC cable to the host, switch or hub.
4. Configuring the library
a. Connect your Ethernet cable to the Ethernet
port at the rear of the library. The library
Ethernet port allows the use of the Web
Client.
b. Connect the two power cords to
the power connectors at the rear of
the library. US and European power cords
are supplied with the library. Two power
cords are required for redundant power supply.
c. Power-on the library (both switches).
d. Power up the host system.
e. Verify that each host can communicate with the library’s tape drives. If you experience problems,
please refer to the troubleshooting guide in the StorageLibrary T40+ Series Installation and User
Guide.
f. Configure your library using the library’s operator panel.
NOTE: The LTO-5 automation tape drives contain an Ethernet port which will enable new features and
functionality at a later time. For more information please refer to www.tandbergdata.com .
Table: Power Requirements
Values
Input Voltage 100 – 240 VAC (1.2 – 0.5 A)
Input Frequency 50 – 60 Hz
Inrush Current (Cold Start) Less than 15 A, 115 VAC
Less than 30 A, 230 VAC
Power Consumption Average 70 W*
Power Consumption Peak* 120 W**
* Value per StorageLibrary T40+ unit with two LTO drives.
** Maximum peak length, less than 10ms.
3


Produktspezifikationen

Marke: Tandberg Data
Kategorie: Nicht kategorisiert
Modell: StorageLibrary T40+
Gewicht: 37700 g
Produkttyp: Speicher-Autoloader & Bibliothek
Betriebstemperatur: 20 - 80 °C
Relative Luftfeuchtigkeit in Betrieb: 10 - 40 %
Montage: Rack
Zertifizierung: CE, FCC, TUV/GS, ICES VCCI, BSMI, CISPR 22, C-tick, UL, C-UL, CB, GOST and EN 55022 Class A
Temperaturbereich bei Lagerung: 10 - 90 °C
Energiebedarf: 100 - 240 VAC, 50 - 60 Hz
Mittlere Betriebsdauer zwischen Ausfällen (MTBF): 250000 h
Abmessungen (BxTxH): 446.6 x 736.6 x 177.5 mm
Unterstützte Medientypen: LTO-4, LTO-3, LTO-2, LTO-1
Medientyp: Bandkartusche
Slot Typ: Mail
Kapazität ohne Komprimierung: 19200 GB
Kapazität (komprimiert): 38400 GB
Backup-Leistung mit Komprimierung: 1700 GB/h
Backup-Leistung ohne Komprimierung: 864 GB/h
Rate nicht erkannter Fehler: < 10(17)
Plattenlaufwerk: LTO-4

Brauchst du Hilfe?

Wenn Sie Hilfe mit Tandberg Data StorageLibrary T40+ benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Nicht kategorisiert Tandberg Data

Bedienungsanleitung Nicht kategorisiert

Neueste Bedienungsanleitung für -Kategorien-