Tandberg Data Overland-Tandberg RDX QuikStor Bedienungsanleitung

Tandberg Data Nicht kategorisiert Overland-Tandberg RDX QuikStor

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Tandberg Data Overland-Tandberg RDX QuikStor (4 Seiten) in der Kategorie Nicht kategorisiert. Dieser Bedienungsanleitung war für 13 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF

Seite 1/4

RDX® QuikStor™

Internal USB and Internal SATA

USB or SATA Cable

Power Adapter Cable

Mounting Screws

AccuGuard License Activation Card

Note: AccuGuard software is only included with

selected RDX products

Quick Start Guide

for USB 3.0

for SATA

Visit the support section of the Tandberg Data web site

(www.tandbergdata.com) for more information, including product

warranty and registration, knowledge base articles, user

documentation and technical support.

For More Information

WHAT‘S IN THE BOX?

The following power ratings represent typical-use performance

USB 3.0

DC Input Voltage and

Rated Input Current

SATA 5V/1.5A

Power Source

Power Ratings

NOTE: This equipment has been tested and found to comply with the limits for a Class B

digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference in a residential installation. This

equipment generates, uses and can radiate radio frequency energy and, if not installed and

used in accordance with the instructions, may cause harmful interference to radio

communications. However, there is no guarantee that interference will not occur in a

particular installation. If this equipment does cause harmful interference to radio or television

reception, which can be determined by turning the equipment off and on, the user is

encouraged to try to correct the interference by one or more of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit diﬀerent from that to which the receiver

is connected.

- Consult the dealer or an experienced radio/ TV technician for help.

FCC Compliance Notice

5V/0.9A and 12V/0.003A

for SATA

for USB 3.0

RDX Emergency Media Eject Pin

For RDX Warranty Registration and

Technical Support Activation visit:

http://registration.tandbergdata.com/

Available External RDX Drives:

8782-RDX: Tandberg RDX External USB3+ Drive, bare

8781-RDX: Tandberg RDX External USB3+ Drive, with software

(Includes AccuGuard Server for RDX deduplication backup software)

A SUBSIDIARY OF

Mount the RDX QuikStor

Install RDX Utility

Connect Data and Power Cables

Load RDX Cartridge

•

Write

Protect

Keyed

Corner

+5VDC

DATA -

DATA +

GND

Key

PIN SIGNAL PIN SIGNAL

1 VCC 2 VCC

3 USB 0- 4 USB 1-

5 USB 0+ 6 USB 1+

7 GND 8 GND

9 Key 10 USBOC

1 2

9 10

USB SATA

Server

Front

RDX QuikStor

5Install AccuGuard Server

for RDX

USB 2.0 cable connector pin-out

RDX QuikStor Features

and LED Status

Emergency

Eject Hole

Eject Button/

Power LED

Activity LED

LED State Media LED Drive LED

Color Activity

Status Description

Status

Description

OFF

STEADY GREEN READY

READY

ACTIVITY

EJECTING

STEADY AMBER FAULT

FAULT

N/A

PREVENT

BLINKING

GREEN

STEADY GREEN

Blinking Am ber

once eject button

is pres sed

Media is not ins erted properly or

is powered down due to low

power m ode and hos t inactivity.

Media is ready

Reading, writing, seeking

RDX has detected a Media fault

condition. For more inform ation,

run a diagnostic application.

RDX has detected a Drive fault

condition. For more inform ation,

run a diagnostic application.

Drive is ejecting Media

RDX is ready and working properly

Drive does not have power.

NOT

READY

POWER

DOWN

Host computer is acces s ing the

media and the us er has press ed the

Eject Button. The drive will eject the

media after the Hos t acces s

com pletes.

P/N 433822 Rev. J

START HERE



Note: The RDX Utility

installs only on Windows.

Go to www.Tandbergdata.com.

Choose “Support” from the main menu.

Click on “Drivers” and Downloads at the right hand side of the page.

Click the “Go”-Button near RDX QuikStor.

Choose “RDX_Utility.zip”.

Click on “Download RDX Utility”.

Unpack the zip-file, start “setup.exe” and follow the installation

instructions.

Power off the computer and open the server cover.

Slide the RDX QuikStor into the drive opening.

Secure the dock with the four supplied mounting screws.

© 2016 Tandberg Data. All rights reserved. RDX QuikStor and AccuGuard are Trademarks of Tandberg Data. RDX is a registered trademark of Tandberg Data S.a.r.l. All other trademarks are the property of their respective owners.

Tandberg Data AccuGuard is only included with selected

RDX products. If your product includes a licence activation

card, follow the instructions for download and installation.

Connect the data cable to motherboard or controller card and then

connect both data cable and power cable to the back of the RDX

QuikStor. The Dock connections are keyed to ensure the correct fit.

SATA interface: SATA controller driver and BIOS support for

AHCI is required, please verify and enable AHCI before you install

the operating system on your computer device.

USB interface: If you encounter connectivity problems, please

order the appropriate aaccessory cable:

Partno. 1020916: USB 3.0 cable intern 810mm (2x10Pin to Type B)