Strymon Conduit MIDI Hub Bedienungsanleitung

Strymon Nicht kategorisiert Conduit MIDI Hub

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Strymon Conduit MIDI Hub (4 Seiten) in der Kategorie Nicht kategorisiert. Dieser Bedienungsanleitung war für 25 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/4
QUICK START GUIDE
POWER
Use an adapter with the following rating: 9VDC center negative, 50mA
minimum. Power supply is not required when connected via USB.
CONTROLS AND CONNECTIONS
GETTING STARTED
Conduit is a premium, easily configurable,
ultra-reliable MIDI interface that will work
with most 1/4" MIDI equipped effects pedals.
It also offers the best USB computer
connection available for TRS MIDI pedals.
SMART MIDI DISTRIBUTION
Each of Conduit’s four bi-directional 1/4" TRS jacks are
independently configurable to work with a variety of 1/4" MIDI
communication modes. Enjoy easy configuration with no DIP
switches, custom cables, or screwdriver required. Built-in ground
isolation ensures the quiet operation you expect from Strymon.
Link multiple Conduits to control additional 1/4" MIDI pedals.
USB INTERFACE FOR YOUR PEDALS
Send MIDI control change messages from a sequencer to
perfectly sync pedal parameter changes, automate pedal
preset changes, load and save presets, or send SysEx
messages—all from your computer.
ACTIVITY LEDs
Activity LEDs will blink when MIDI information is present at a 1/4" jack.GREEN
SET BUTTON
Used for TRS MIDI I/O Jack configuration.
The button can be pressed at any time to SET
show configuration state of 1/4" TRS jacks.
USBC
Used for computer connectivity. See the Using
Conduit with a Computer section.
DIN MIDI I/O Jacks
MIDI IN receives MIDI data from an external MIDI
controller and sends the data to all four 1/4" jacks.
All MIDI data sent back from 1/4" TRS connected
pedals is merged and sent to the . MIDI OUT
When is connected, MIDI data received at the USB
1/4" jacks from the connected pedals is no longer
merged to the MIDI OUT port, but is instead sent to
the connected computer via it’s own MIDI port.
STATUS LED for 5-pin DIN I/O
Status LED lights up to indicate Conduit is powered on and will GREEN
flash when MIDI data is passing through Conduit to the 1/4" jacks.AMBER
1/4" TRS MIDI I/O Jacks 1-4
Out of the box, Conduit’s 1/4" TRS MIDI jacks are configured to work with
Strymon pedals, with no further setup necessary. Each jack is capable
of sending and receiving MIDI data, and can be configured to work with a
variety of different 1/4" MIDI communication modes. You can find out which
configuration will work with your specific pedals by visiting strymon.net/
support/conduit.
WELCOME TO CONDUIT
5
6
Connect a power supply (not included) that provides 9V DC
center-negative power and at least 50mA of current to the 2.1mm
9VDC power input.
Set the MIDI Channel that your pedal will be communicating on.
The default MIDI Channel on Strymon pedals is Channel 1.*
When Conduit powers up, the LEDs will light up to show that
the device is powered. The color of the four 1/4" OUTPUT LEDs
will show the current I/O configuration. The factory default I/O
configuration for all four 1/4" TRS jacks is NORMAL mode ( GREEN
- Tip send). This is the configuration used by Strymon pedals.
Go to for details on changing the strymon.net/support/conduit
output configuration for non-Strymon pedals.
Set the MIDI OUT mode on the pedal. If you are only sending
MIDI data to the pedal without sending anything back out from
the pedal, set the MIDI OUT of the pedal mode to OFF.
If you would like to echo the MIDI data received from the
pedals connected to the 1/4" jacks, set the MIDI OUT mode to
THROUGH.*
Connect a 5-pin DIN MIDI cable from the port of your MIDI OUT
MIDI controller or MIDI interface into the port on Conduit.MIDI IN
Sending MIDI messages from your MIDI controller or interface
to Conduit will now distribute these messages to devices
connected to the 1/4" TRS jacks and 5 pin DIN port.MIDI OUT
All MIDI data received at the 1/4" jacks from the pedals are
merged and sent to the 5 pin DIN MIDI port.
* Go to for more details on configuring your strymon.net/support/conduit
Strymon pedals to communicate via MIDI. For third party 1/4" MIDI
capable pedals, please see the user manual for the device.
Connect one of the included 1/4" TRS cables to one of the 1/4" I/O
jacks on Conduit. Connect the other end to the 1/4" MIDI control
input on your pedal. On compatible Strymon pedals, connect to the
EXP MIDI or jack set to MIDI mode.*
TRS 1/4” CABLE
5-PIN DIN MIDI CABLE
CONNECTING YOUR 1/4" MIDI DEVICES TO CONDUIT
1
2
3
4


Produktspezifikationen

Marke: Strymon
Kategorie: Nicht kategorisiert
Modell: Conduit MIDI Hub

Brauchst du Hilfe?

Wenn Sie Hilfe mit Strymon Conduit MIDI Hub benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Nicht kategorisiert Strymon

Bedienungsanleitung Nicht kategorisiert

Neueste Bedienungsanleitung für -Kategorien-