Strymon Bluesky Bedienungsanleitung


Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Strymon Bluesky (6 Seiten) in der Kategorie Nicht kategorisiert. Dieser Bedienungsanleitung war für 18 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/6
®
Reverberator
USER MANUAL
blueSky - reverberator User Manual ®
pg 2
DECAY: Controls the decay
time of the reverberated signal.
Set low for small rooms, plates
and short springs. Set high for
huge arenas, massive plates
and enormous springs.
PRE-DELAY: Controls the delay time
before the reverberated signal appears.
This is an essential control in creating an
accurate and pleasing reverb.
TIP: for most natural results, use lower
MIX settings when using higher Pre-delay.
MIX: Controls the balance of dry
signal wet signal and from 100%
dry at minimum to 100% wet
at maximum. The occurs mix
entirely in analog.
LOW DAMP:
Controls the
amount of Low
Damping in the
reverberated signal.
Acts essentially
like a tone control
resulting in more or
less low end in the
reverb decay trail.
HIGH DAMP:
Controls the amount of
High Damping in the
reverberated signal.
Acts essentially like a
tone control resulting in
more or less high end in
the reverb decay trail.
FAVORITE FOOTSWITCH:
Press to select saved favorite sound. When FAVORITE LED is lit
the favorite setting is engaged. When each knob is turned, the
LED will indicate the saved favorite position of the knob. Push and
hold the foot switch to save a new favorite sound.
BYPASS FOOTSWITCH:
Engages and disengages effect. Bypass mode is true bypass by
default. LED on indicates that the effect is engaged. Hold TIP:
the bypass footswitch during power up to change the bypass
mode to analog bypass with (reverb persist).trails
TIP: Hold down FAVORITE and BYPASS MIX while turning the knob to achieve a +/- 3dB
Boost or Cut when the pedal is engaged (12:00 on the Mix knob is unity gain).
MIXDECAY
PRE-DELAY
norm
mod
shimmer
BYPASSFAVORITE
®
HIGH DAMPLOW DAMP
MODE TYPE
plate
room
spring
re ve rb era t or
Front Panel
MODE SWITCH:
Switches between 3 reverb modes (normal,
mod, shimmer). mode provides an Normal
unmodified version of the selected reverb type.
Mod adds gorgeous modulation to the selected
reverb type. mode adds regenerative Shimmer
octave up pitch shifting “in the tank” for a
reverb trail that rises into the clouds with
a plate. For Spring and Room shimmer, an
octave plus a fifth is regeneratively introduced.
TYPE SWITCH:
Switches between 3 different types of reverb (plate,
room, spring). Plate gives you an intensely high
quality vintage studio plate type reverb. Room
type is a versatile room ranging in size from a
bedroom to an arena. Spring provides an excellent
recreation of the best vintage spring reverbs.
TIP: Adjust LOW DAMP and HIGH DAMP controls
with the spring type reverb to vary the color and
age of your spring tank.
blueSky - reverberator User Manual ®
pg 3
RIGHT IN
LEFT IN
9VDC
+-
RIGHT OUTLEFT OUT
High impedance stereo
inputs. Use for LEFT IN
mono signal input.
Stereo outputs. Use
LEFT OUT for mono
signal output.
Standard 9V DC
center negative
power input.
200 mA power
consumption.
Rear Panel


Produktspezifikationen

Marke: Strymon
Kategorie: Nicht kategorisiert
Modell: Bluesky

Brauchst du Hilfe?

Wenn Sie Hilfe mit Strymon Bluesky benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Nicht kategorisiert Strymon

Bedienungsanleitung Nicht kategorisiert

Neueste Bedienungsanleitung für -Kategorien-