Sony MZ-E510 Bedienungsanleitung

Sony Nicht kategorisiert MZ-E510

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Sony MZ-E510 (2 Seiten) in der Kategorie Nicht kategorisiert. Dieser Bedienungsanleitung war für 3 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF
Seite 1/2
B
The elapsed time
Track name
Group name
Disc name
Sound mode
SP/LP mode
Getting started
Charge the supplied rechargeable battery before using it for the first time.
Insert the rechargeable battery.
b
e
E
b
Charge the rechargeable battery.
b
The battery condition is indicated by the “3-color info-LED” on the player:
Red Orange t t LED off (approx. 2.5 hours later)
The player can be used when the LED has turned off.
Note
If you start playback or do another operation during charging, the charging will stop.
Using the dry battery
2
1
b
4
3
Insert a LR6 (size AA) alkaline dry battery.
To operate the player for the longest possible time, use the dry battery together
with a fully charged rechargeable battery.
Make connections and unlock the controls.
HOLD
HOLD
Using the clip for the remote control
It may be hard for you to read the indications in the display if the remote control is
attached upside down with the clip in its current position. In this case, attach the clip
in the opposite direction as shown below.
1 2Remove the clip. Attach the clip in the opposite direction.
1
2
Operating Instructions
Portable MiniDisc Player
MZ-E510
© 2002 Sony Corporation Printed in Japan
3-250-259- (1)12
WARNING
To prevent fire or shock hazard, do not expose the
unit to rain or moisture.
Do not install the appliance in a confined space, such as a bookcase or built-in cabinet.
To prevent fire, do not cover the ventilation of the apparatus with newspapers, table- cloths,
curtains, etc. And don’t place lighted candles on the apparatus.
To prevent fire or shock hazard, do not place objects filled with liquids, such as vases, on the
apparatus.
Certain countries may regulate disposal of the battery used to power this product. Please
consult with your local authority.
Caution
The use of optical instruments with this product will increase eye hazard.
CAUTION — INVISIBLE LASER RADIATION WHEN OPEN
DO NOT STARE INTO BEAM OR VIEW DIRECTLY WITH OPTICAL INSTRUMENTS
Information
IN NO EVENT SHALL SELLER BE LIABLE FOR ANY DIRECT, INCIDENTAL OR
CONSEQUENTIAL DAMAGES OF ANY NATURE, OR LOSSES OR EXPENSES RESULTING
FROM ANY DEFECTIVE PRODUCT OR THE USE OF ANY PRODUCT.
The validity of the CE marking is restricted to only those countries where it is legally enforced,
mainly in the countries EEA (European Economic Area).
Attach the dry battery case to the
player.
3
Insert the battery minus end first.
BVarious ways of
playback
Remote control
Volume control
HOLD
DISPLAY
SOUND
x
+, –
P MODE/
Jog lever ( /ENT • ). • u >
Player (at the bottom)
. >,
u
GROUP
VOLUME +, –
x
Selecting the play mode
You can select from the various play modes
using the P MODE/ button on the remote
control.
1Press P MODE/ repeatedly.
Each time you press the button, the
play mode changes as follows:
Play mode indication
Display*
(none)
(normal play)
1
(single-track play)
(bookmark play)
SHUF
(shuffle play)
PGM
(program play)
* Group play mode ( ) appears whenever you
play a disc with group settings. For more
details, see “Using the group function.”
Playing a track repeatedly
(Repeat Play)
You can use the repeat function for normal
play, single-track play, shuffle play, and
program play mode.
1During playback in the selected play
mode, press and hold P MODE/ for
2 seconds or more.
“ ” appears in the display.
Repeat play indication
To cancel repeat play
Press and hold P MODE/ for 2 seconds or
more.
z
By pressing the P MODE/ button during
repeat play, you can change the play mode to be
used with repeat play.
To
Pause
Cue to the current track
or the previous track
Cue to the next track
Go backwards or
forward while playing
Searching for a specific
position while viewing
a elapsed time
(Time search)
Searching for a specific
track while viewing
track numbers
(Index search)
Cue to the beginning of
every 10th track
(only during playback of
the disc with no group
settings1))
Remove the MD
1) For more details, see “Using the group function.”
2) Once you open the lid, the point to start play will change to the beginning of the first track.
About the “3-color info-LED”
The LED indicates the current operating mode, charging status, and battery condition. For
details about the charging status, see “Getting started.” For details about the battery condition,
see “When to replace or recharge the battery” on the back page.
LED color
Red
Green
Orange
Do this (Beeps in the headphones/earphones)
Press the jog lever ( ) on the remote control (continuous shortu
beeps). (Press u on the player.)
Press the jog lever ( on the player) again to resume play.u
Slide the jog lever towards on the remote control.
(three short beeps). (Press on the player.).
Slide the jog lever towards on the remote control (two short>
beeps). (Press on the player.)>
Slide and hold the jog lever towards or on the remote. >
control. (Press and hold on the player.). or >
While the player is paused, slide and hold the jog lever towards
. > or on the remote control.
While the player is stopped, slide and hold the jog lever towards
. > or on the remote control.
Press + or – button.
Press x, and then slide OPEN.2)
“Charging” flashes when charging starts.
1
2
to a wall
outlet
Playing an MD
Insert an MD.
1
2
3
Play an MD.
( • /ENT• ). u >
. >,
u
VOLUME +, –
+, –
x
x
VOL+
VOL–
1Press the jog lever (u u) on the remote control. (Press on the player.)
A short beep sounds in the headphones/earphones. The LED lights up.
2Turn the volume control towards VOL + or – on the remote control to adjust
the volume. (Press VOLUME + or – on the player. )
The volume indicator appears in the display, allowing you to check the
volume level.
To stop play, press x.
A long beep sounds in the headphones/earphones.
Playback starts from the point you last stopped playing. To start playback from the
beginning of the disc, press and hold the jog lever ( ) for 2 seconds or more on theu
remote control (Press and hold for 2 seconds or more on the player).u
1
2
Insert an MD with the label side facing up, pushing the
MD to the direction of the arrow in the illustration.
1 2 3 Slide OPEN to open the lid. Insert an MD. Close the lid.
“3-color info-LED”
“3-color info-LED”
Listening to selected tracks
only (Bookmark Play)
You can bookmark tracks on a disc and play
them only. The sequence of bookmarked
tracks cannot be changed.
To bookmark the tracks
1While playing the track you want to
bookmark, press and hold the jog lever
for 2 seconds or more.
Flashing slowly
The first track for bookmark play is set.
2Repeat step 1 to bookmark other tracks.
You can bookmark with up to 15 tracks.
To play the bookmarked tracks
1During playback, press P MODE/
repeatedly until “ TrPLAY?” appears
in the display.
2Press the jog lever.
The bookmarked tracks start playing,
starting with the smallest track number.
To erase a bookmark
While playing the track for which you want
to erase the bookmark, press and hold the jog
lever for 2 seconds or more.
Note
If you open the lid, all bookmarks are
canceled.
Listening to tracks in a desired
sequence (Program Play)
1During playback, press P MODE/
repeatedly until “PGM” appears in the
display.
2Slide the jog lever repeatedly to select
a track, and then press the jog lever to
enter that track.
track number programmed number
3Repeat step 2 to program more tracks.
You can program up to 15 tracks.
4After programming the tracks, press
and hold the jog lever for 2 seconds or
more.
The program is stored and playback
starts from the first track.
z
The program play settings will remain in
memory even after playback finishes or is
stopped.
Note
All program settings are lost when the lid is
opened.
Repeat play for the selected
group play mode (Group
Repeat Play)
1During playback in the selected group
play mode, press and hold
P MODE/ for 2 seconds or more.
Playback repeats in the respective
group mode.
Display
SHUF
PGM
Playing groups in a desired
sequence
(Group Program
Play)
Do the procedure explained in “Listening to
tracks in a desired sequence (Program Play)”
to play back groups in a desired sequence.
You can program up to 10 groups. The
sequence of tracks within the groups cannot
be changed.
Registering groups using an
MD recorder
An MD recorder with the group function
Refer to the operating instructions of the MD
recorder.
An MD recorder that does not support the
group function
The procedure below allows you to assign
tracks to a group using the disc name-editing
function.
Specifying groups
1Change the disc name to the following
by using the MD recorder:
0;[Disc name] // [First track of group 1 ]-
[Last track of group 1] ; [Name of group 1 ] //
A
B B
[Name of group 2] // ......
B
B
C
[First track of group 2] - [Last track of group 2 ] ;
C
ADisc name
BTrack number
CGroup name
// Separator between groups
– Hyphen placed between the first
track and the last track
; Separator between track number and
Group name
(Ex.) Set the following groups for the disc
named “Collections ”:
Group name for tracks 1-7:
My Favorites“2003winter”
Group name for tracks 8-17:
Jun&Tac“sunshine head”
Group name for tracks 18-24:
THE NIGHT BUTTERFLYS
Group name for tracks 25-32:
Dream World/Kiss Me!
Text string entered
0;Collections//
1–7;My Favorites“2003winter”//
8–17;Jun&Tac“sunshine head”//
18–24;THE NIGHT BUTTERFLYS//
25–32;Dream World/Kiss Me!//
z
• The characters “;”, “/”, and “–” can be used in
a group name.
• You can register the same group name more
than twice on the same MD.
• You can specify a group without entering a
group name (C) for it.
Notes
• Up to 99 groups can be registered on a single
MD. The actual number, however, will be less
than 99 if you have entered more characters
than are allowed per disc.
• Depending on the specifications of your MD
recorder, the group function may not work.
Adjusting the sound
(6-Band Equalizer)
You can select from 6 kinds of sound
qualities.
1During playback, press SOUND
repeatedly to select “SOUND.”
2Press and hold SOUND for 2 seconds
or more.
3Slide the jog lever repeatedly to select
the SOUND mode.
Each time you slide the jog lever, A
and B change as follows:
A B
HEAVY SOUND H
POPS SOUND P
JAZZ SOUND J
UNIQUE SOUND U
CUSTOM1 SOUND 1
CUSTOM2 SOUND 2
4Press the jog lever to enter the selected
SOUND mode.
To cancel the procedure
Press and hold the DISPLAY button or the x
button for 2 seconds or more.
To cancel the setting
Slide the jog lever repeatedly in step 1 above
until the indication at disappears.B
To modify and store the sound
You can customize the sound settings in
“CUSTOM1” and “CUSTOM2.”
1Do steps 1 to 3 above, and then slide the
jog lever until “CUSTOM1” or
“CUSTOM2” appears.
2Press the jog lever.
3Slide the jog lever repeatedly to select the
frequency.
Frequency (100 Hz)
From the left, you can select 100 Hz,
250 Hz, 630 Hz, 1.6 kHz, 4 kHz, or 10 kHz.
4Turn the volume control repeatedly to
adjust the level.
Level (+10 dB)
You can select from among seven
levels.
–10 dB, –6 dB, –3 dB, 0 dB, +3 dB,
+6 dB, +10 dB
5Repeat steps 3 and 4 to adjust the level
for each frequency.
6Press the jog lever to enter the selection.
BOther operations
Viewing the track name
and playing time in the
display on the remote
control
You can check the track or disc name, track
number, the elapsed playing time of the
current track, the number of the tracks
recorded on the MD, the group name, and the
total number of tracks in a group.
A B
1Press DISPLAY on the remote control.
Each time you press DISPLAY, the
display changes as the follows:
A
Track number
Track number
The number of total
tracks in the group
The number of
total tracks
Track number
Track number
Notes
• Depending on whether group play or normal
play is selected, the operating conditions, and
the disc settings, you may not be able to select
certain indications or the indications may
appear different.
• During playback, the SP/LP mode appears
momentarily, and is then replaced by the
elapsed time of the current track.
Suppressing the skips of
the sound (G-PROTECTION)
The G-PROTECTION function was
developed to provide a higher level of shock
resistance than that of existing players in
order to allow the player to be used while
jogging.
Note
The playback sound may skip if:
• the player receives stronger continuous shock.
• a dirty or scratched MiniDisc is played.
to DC IN 3V
Play mode
All the tracks are played
once.
A single track is played
once.
Bookmarked tracks play
back in order of their
track number.
All the tracks are played
in random order.
The tracks are played in
the order that you
specified.
Play mode
All tracks in the groups
play back once (starting
with the first track in
group 1).
Shuffle play starts with
the group that is
currently playing, and
continues with the
succeeding groups.
The groups are played in
the order that you
specified.
Insert the battery minus end first.
The battery charging stand
(at the bottom)
The “3-color info-LED” lights up in
red when charging starts.
AC power
adaptor
Jog lever
Play mode
Repeat play of tracks
within a group
Repeat shuffle play of
tracks within a group
Repeat play for group
program
Group 1 Group 2 Group 3
Using the group function
The group function is provided to allow
playback of discs with group settings. The
group function is convenient for playback of
MDs on which several albums or CD singles
have been recorded in MDLP (LP2/LP4 )
mode.
What is a disc with group settings?
The player can play back tracks in units of
groups; that is tracks that have been recorded
on a disc as part of separate groups, as shown
below.
The “3-color info-LED” lights up in green
when a disc with group settings is being
played.
Before group settings are made
(normal play)
1 2 4 5 6 7 8 1213 14 153
mTrack 1 to 5 are assigned to group 1.
Track 8 to 12 are assigned to group 2.
Track 13 to 15 are assigned to group 3.
Track 6 and 7 are not assigned to a
group.
After setting the group (group play)
12345 6 7 12345 123
Tracks that were not assigned to a group are
treated as being part of “Group - -.”
Note
The player does not support the recording of
group settings. Use an MD recorder to set the
group. For details, see “Registering groups using
an MD recorder.”
Playing a track in group play
In group play, all groups are played in order,
starting with group 1, followed by the
unassigned tracks (“Group - -”). Playback
stops after all the tracks have been played.
1During playback, press P MODE/
repeatedly until “ ” appears in the
display.
Cueing to the start of a group
(Group Skip)
On the remote control
1During playback, press + or –.
Pressing the – button cues to the first
track in the current group. Pressing the
button again cues to the first track of the
previous group. During group cueing,
the “3-color info-LED” on the player
flashes in orange.
On the player
1During playback, press GROUP.
The “3-color info-LED” on the player
lights up in orange.
2Press .. or >
Selecting the play mode for
group play (Group Play Mode)
The shuffle play and program play function
can be used during group play mode.
1Press P MODE/ repeatedly.
After normal playback, the following
play modes are displayed:
Display
(Normal Group
Play)
SHUF
(In-Group Shuffle)
PGM
(Group Program)
Disc
Disc
NH-10WM
“WALKMAN” is a registered trademark of Sony Corporation to
represent Headphone Stereo products. is a
trademark of Sony Corporation.
Operating status
Playing a disc with no group settings
Playing a disc with group settings
Cueing to another group (Group Skip)
To i jack
Connect firmly.
Clip
Player (at the bottom)
BOther operations (continued)
Remote control
Volume control
HOLD
DISPLAY
SOUND
x
+, –
P MODE/
Jog lever (. u >• /ENT• )
Player (at the bottom)
HOLD
VOLUME +, –
“3-color info-LED”
Starting playback quickly
(Quick Mode)
After pressing the playback button or cueing
to a track, you can start playback quickly.
This procedure can be done by the remote
control.
1Press and hold DISPLAY for 2 seconds
or more.
2Slide the jog lever repeatedly until
“PowerMode” appears in the display,
and then press the jog lever.
3Slide the jog lever repeatedly until
“QUICK” appears in the display, and
then press the jog lever to enter the
selection.
“QUICK” appears in the display.
To cancel the procedure
Press and hold the DISPLAY button or the x
button for 2 seconds or more.
To cancel the setting
Select “NORMAL” in step 3 above.
Notes
•
When the power mode is set to “QUICK,” the
power remains on within the player even when
nothing appears in the display. This leads to a
shorter battery life. For this reason, it is
recommended that you charge the battery
daily.
• If no player operation (including opening or
closing of the lid) occurs for 17 hours, the
power in the player automatically turns off.
For this reason, the next time you start
playback or do another operation, the player
will not respond quickly. The unit, however,
will return to quick mode afterwards.
Locking the controls (HOLD)
1Slide HOLD on the remote control in
the > direction, and slide HOLD on
the player in the direction.l
Sliding HOLD on the remote control
disables the controls on the remote
control. Sliding HOLD on the player
disables the controls on the player.
To unlock the controls
Slide HOLD to the opposite directions of the
arrows.
Preserving battery power
(Power Save Mode)
This function allows you to maximize the
operating life of the battery. Power
consumption is reduced by turning off the
“3-color info-LED” at all times, or by turning
off the display when no operation has been
made for a while.
This procedure can be done by the remote
control.
1Press and hold DISPLAY for 2 seconds
or more.
2Slide the jog lever repeatedly until
“PowerMode” appears in the display,
and then press the jog lever.
3Slide the jog lever repeatedly until
“PowerSave” appears in the display,
and then press the jog lever to enter
the selection.
The “3-color info-LED” turns off.
To cancel the procedure
Press and hold the DISPLAY button or the x
button for 2 seconds or more.
To turn on the “3-color info-LED”
Select “NORMAL” in step 3 above.
Protecting your hearing
(AVLS)
AVLS (Automatic Volume Limiter System)
function keeps down the maximum volume
to protect your ears.
1During playback, press and hold
DISPLAY for 2 seconds or more.
2Slide the jog lever repeatedly until
“AVLS” appears in the display, and
then press the jog lever.
3Slide the jog lever repeatedly until
“AVLS ON” appears in the display,
and then press the jog lever to enter
the selection.
“AVLS ON” appears in the display.
To set the AVLS function on the
player
During playback, slide HOLD in the direction
of , and then while pressing VOLUME –,l
slide HOLD in the opposite direction.
To cancel the AVLS function
On the remote control, select “AVLS OFF” in
step 3 above and press the jog lever.
On the player, during playback, slide HOLD
in the direction of , and then whilel
pressing VOLUME +, slide HOLD in the
opposite direction.
Turning off the beep
sound
You can set the beep so that it is not emitted
when the player and the remote control are
operated.
This procedure can be done by the remote
control.
1Press and hold DISPLAY for 2 seconds
or more.
2Slide the jog lever repeatedly until
“BEEP” appears in the display, and
then press the jog lever.
3Slide the jog lever repeatedly until
“BEEP OFF” appears in the display,
and then press the jog lever to enter
the selection.
To cancel the procedure
Press and hold the DISPLAY button or the x
button for 2 seconds or more.
To cancel the setting
Select “BEEP ON” in step 3 above.
Turning on/off the
backlight in the display on
the remote control
You can set the backlight in the display on the
remote control.
This procedure can be done by the remote
control.
1Press and hold DISPLAY for 2 seconds
or more.
2Slide the jog lever repeatedly until
“BACKLIGHT” appears in the display,
and then press the jog lever.
3Slide the jog lever repeatedly to select
one of the following settings:
Display
AUTO
ON
OFF
4Press the jog lever to enter the setting.
BPower sources
When to replace or
recharge the battery
You can check the battery condition through
the battery indicator on the remote control
and the “3-color info-LED” on the player
while using the player.
Indicator on the remote control
Battery power decreasing
v
Weak battery
v
The battery has gone out.
“LOW BATT” flashes in the
display, and the power goes off.
Indicator of the “3-color info-LED” on the
player
The LED lights up. There is sufficient
battery power.
v
The LED flashes slowly. Battery power
decreasing
v
The LED flashes quickly. The battery is low.
The LED will soon
turn off and the
supply of power will
stop.
Notes
• The battery indicator may show the battery to
be fully charged even when it is not. Charging
the battery shorter than the prescribed time
will result in a shorter operating time on the
player.
• A stronger or weaker battery charge may be
indicated when you fast forward or fast reverse
an MD, or when you use the player at a very
cold place.
Battery life1)
(Unit: Approx. hours) (JEITA 2))
Batteries
Ni-MH
rechargeable
battery
NH-10WM3)
LR6 (SG)
Sony Alkaline
dry battery4)
LR6 (SG)4) and
NH-10WM3)
1) Measured with the power save function on (see
“Preserving battery power”).
2) Measured in accordance with the JEITA (Japan
Electronics and Information Technology
Industries Association) standard (using a Sony
MDW-series Mini-disc).
3) With a fully charged battery
4) When using a Sony LR6 (SG) “STAMINA”
alkaline dry battery (produced in Japan).
Note
The battery life may be shorter than that
specified, depending on the temperature of the
location, the operating conditions, and the type
of battery being used.
Using house current
You can operate the player without a
rechargeable battery or a dry battery. To do
this, connect the battery charging stand to an
AC outlet through the AC power adaptor,
and then place the player on the stand.
BAdditional information
Precautions
On safety
• Make sure to keep the player in the supplied
carrying pouch. If the terminals on the player,
battery-charging stand, or battery case are
accidentally brought into contact with a
metallic object, they may short-circuit and
begin to heat up.
• Keep the terminals on the player or on the
battery case away from metallic objects or
surfaces. Such contact may short-circuit the
terminals and cause dangerous heat
generation. When carrying the player with
you, always keep the battery case attached to
the player in the supplied carrying pouch.
• When you carry the supplied rechargeable
battery, be sure to put it in the supplied
rechargeable battery carrying case. Carrying
the rechargeable battery without the case may
cause a short-circuit with metallic objects such
as coins, key rings, or necklaces. As a result,
heat may be generated.
• Do not put any foreign objects in the DC IN
3V jack.
• Do not carry or store the dry battery or battery
case in the same place with metallic objects
such as coins, key rings, or necklaces. This
may cause a short-circuit and the generation
of heat.
• Incorrect battery usage may cause the battery
fluid to leak or battery to burst. To prevent
such accidents, observe the following
precautions:
— Install battery with the + and – poles
aligned correctly.
— Do not charge dry battery.
• If a battery leak should develop, carefully and
thoroughly wipe away the battery fluid in the
battery compartment before inserting a new
battery.
• If you will not use the player for a long time,
be sure to disconnect the power supply (AC
power adaptor, dry battery, rechargeable
battery, or battery charging stand). When
disconnecting the AC power adaptor from the
electrical outlet, grasp the adaptor plug itself;
never pull the cord.
On the AC power adaptor (for the
supplied battery charging stand)
• For use in your house: Use the supplied AC
power adaptor. Do not use any other AC
power adaptor since it may cause the player to
malfunction.
Polarity of the plug
• Connect the AC power adaptor to an easily
accessible AC outlet. Should you notice an
abnormality in the AC power adaptor,
disconnect it from the AC outlet immediately.
On charging
• The supplied battery charging stand can be
used only with the MZ-E510. It cannot be
used to charge any other models.
• Do not use the supplied battery charging
stand to charge any other battery besides the
one designated for it.
• Charge the rechargeable battery at a
temperature of +5°C (+41°F) to +40°C
(+104°F). The charging time will vary
according to the surrounding temperature.
• The battery charging stand and the battery
may become hot during the charging
procedure; this, however poses no danger.
• Because of the battery’s characteristics, the
capacity of the battery may be smaller than
normal when it is used for the first time or
after a long period of disuse. In this case,
charge and discharge the battery several
times. The normal battery life will be
restored.
• If the capacity of the rechargeable battery
drops to half the normal amount, replace it
with a new one.
• As soon as the charging is complete, remove
the player from the battery charging stand
and disconnect the battery charging stand
from the electrical outlet. Leaving it
connected may result in reduced battery
performance.
On handling
• Do not drop or bump the player. This may
cause the player to malfunction.
• Do not pull on the remote control or
headphones/earphones cords.
• Do not place the player in the following
places:
— An extremely hot place (over +60°C
(+140°F))
— A place exposed to direct sunlight or near a
heater
— In a car with the windows rolled up
(especially in the summer)
— In a damp place such as a bathroom
— Near a source of electromagnetic fields
such as a magnet, speaker, or TV
— In a dusty place
On heat build-up
Heat may build up in the player when it is
charging or operated for a long time. This,
however, is not a malfunction.
On mechanical noise
The player emits mechanical noise while
operating, which is caused by the power-
saving system of the player. This is not a
malfunction.
On installation
• Never use the player where it will be
subjected to extremes of light, temperature,
moisture or vibration.
• Never wrap the player in anything when it is
being used with the AC power adaptor. Heat
build-up in the player may cause malfunction
or injury.
On the remote control
The supplied remote control is designed for
use with the MZ-E510 only. Note also that
the player cannot be controlled by remote
controls for other models.
On the MiniDisc cartridge
• Do not touch the internal disc directly.
Forcing the shutter open may damage the
internal disc.
• When transporting a minidisc, keep it in its
case.
• Do not place the cartridge where it will be
subjected to light, temperature, moisture or
dust.
• Do not affix the label outside of the specified
area on the MD. Make sure the label is placed
within the recessed space on the disc.
On the headphones/earphones
Road safety
• Do not use headphones/earphones while
driving, cycling, or operating any motorized
vehicle. This may lead to a traffic accident
and is illegal in many areas. It can also be
potentially dangerous to play your player at
high volumes while walking, especially at
pedestrian crossings. You should exercise
extreme caution or discontinue using the
player in potentially hazardous situations.
• If you experience an allergic reaction to the
supplied headphones/earphones, stop using
them at once and consult a doctor or a Sony
service center.
Preventing hearing damage
Avoid using headphones/earphones at high
volumes. Hearing experts advise against
continuous, loud and extended play. If you
experience a ringing in your ears, reduce the
volume or discontinue use.
Caring for others
Keep the volume at a moderate level. This
will allow you to hear outside sounds and to
be considerate of the people around you.
On the battery case
The supplied battery case is designed for use
with the MZ-E510 only.
On cleaning
• After wiping the player casing with a soft
cloth slightly moistened with water, wipe it
again with a dry cloth. Do not use any type of
abrasive pad, scouring powder or solvent
such as alcohol or benzene as this may mar
the finish on the casing.
• Wipe the disc cartridge with a dry cloth to
remove dirt.
• Dust on the lens may prevent the unit from
operating properly. Be sure to close the disc
compartment lid after inserting or ejecting an
MD.
• To maintain good sound quality, use a soft
cloth to clean the plugs of the headphones/
earphones and remote control. A dirty plug
may cause noise or intermittent breaks in the
sound during playback.
• Clean the terminals periodically with a cotton
swab or a soft cloth as illustrated.
Rechargeable battery compartment
Dry battery case
Rechargeable battery (supplied)/
Dry battery (not supplied)
Battery charging stand
If you have any questions or problems
concerning your player, please consult your
nearest Sony dealer. (If a trouble occurred
when the disc was in the player, we
recommend that the disc be left in the player
when you consult your Sony dealer so that
the cause of trouble may be better
understood.)
SP
Stereo
LP2 LP4
(normal)
Stereo Stereo
26 32 42
57 72 91
85 107 130
Troubleshooting
The rechargeable battery does not start
charging.
•The terminals of the battery charging
stand are dirty.
b
Wipe the terminals with a dry cloth.
•The rechargeable battery is not inserted
in the player.
b
Insert the rechargeable battery into
the player.
•
The surrounding temperature is too high
or too low (“CannotCHG” appears in the
display when the surrounding
temperature is too high, or “SLOW
CHG” when temperature is too low).
b
Charge the battery at a temperature
of +5°C (+41°F) to +40°C (+104°F).
The “3-color info-LED” does not light up
even when the player is placed on the
battery charging stand.
•The rechargeable battery is not inserted
in the player.
b
Insert the rechargeable battery into
the player.
• The LED may not light on immediately
after you placed the player on the
battery charging stand.
b
The LED will light up after about 3
minutes and charging will begin.
The player does not work or works
poorly.
•The rechargeable battery or dry battery
has been installed incorrectly.
b
Install the battery with correct
polarity.
•You tried to play with no disc in the
player (“NO DISC” appears on the
remote control).
b
Insert an MD.
•The hold function is activated and the
controls are locked. (If you press any of
the operation buttons on the player,
“HOLD” appears on the remote
control.)
b
Slide HOLD in the opposite
direction of the arrow to release the
hold function.
•You pressed on a button on the player
while making a setting on the remote
control. (“MENU” appears on the
remote control when a button on the
player is pressed.)
b
End the setting procedure using the
remote control.
•Moisture has condensed inside the
player.
b
Take the MD out and wait for
several hours until the moisture has
evaporated.
•The rechargeable battery or dry battery
is weak (“LOW BATT” appears on the
remote control).
b
Insert a new dry battery or recharge
the battery.
•An MD with nothing recording on it is
inserted (“BLANKDISC” appears on
the remote control).
b
Insert a recorded MD.
•The player cannot read the disc. (it’s
scratched or dirty) (“READ ERR” or
“TOC ERR”appears on the remote
control.)
b
Reinsert or replace the disc.
•While operating, the player received a
mechanical shock, too much static,
abnormal power voltage caused by
lightning etc.
b
Restart the player as follows:
1Disconnect the power source.
2Let the player sit for about
30 seconds.
3Reconnect the power source.
There is no sound output from the
headphones/earphones.
•The headphones/earphones plug is not
firmly inserted.
b
Insert the headphones/earphones
plug firmly to the remote control.
b
Insert the headphones/earphones
plug firmly into the i jack.
•AVLS is on.
b
Cancel the AVLS function. For more
details, see “Protecting your
hearing.”
The MD does not play normally.
•The player is set to the repeat mode.
b
Press and hold the P MODE/
button on the remote control until
“ ” disappears, then start playing.
The MD does not play from the first
track.
•The disc stopped playing before
reaching the last track.
b
Open the lid or when the player
stops, press and hold the jog lever
for 2 seconds or more to start
playing from the first track.
The playback sound skips.
•The player is placed where it receives
continuous vibration.
b
Place the player at a stable place.
•A very short track may cause sound to
skip.
The sound has a lot of static.
•Strong magnetism from a television or
other device causing interference.
b
Move the player away from the
source of strong magnetism.
Noise is momentarily heard.
•The sound was recorded in LP4 stereo
mode.
b
Because of the nature of the
compression method used in LP4
mode, noise may be output on very
rare occasions during playback of
sound recorded in this mode.
During playback, the “3-color info-LED”
or display on the remote control does
not turn on.
•Power save mode is activated.
b
In power save mode, the display on
the remote control turns on
whenever the remote control is
operated, but not when the controls
on the player are operated. (The
exception is when the GROUP
button on the player is pushed.)
The group function does not function.
•A disc that has no group settings is
inserted.
b
Insert a disc with group settings.
Bookmark play on the player is not
possible. (“NoEntry” appears in the
display on the remote control.)
•You tried to select bookmark play
without setting bookmarks.
b
Set bookmarks.
Specifications
Audio playing system
MiniDisc digital audio system
Laser diode properties
Material: GaAlAs
Wavelength: λ = 790 nm
Emission duration: continuous
Laser output: less than 44.6 µW*
* This output is the value measured at a distance
of 200 mm from the objective lens surface on
the optical pick-up block with 7 mm aperture.
Revolutions
Approx. 300 rpm to 2,700 rpm
Error correction
ACIRC (Advanced Cross Interleave Reed
Solomon Code)
Sampling frequency
44.1 kHz
Coding
ATRAC (Adaptive TRansform Acoustic Coding)
ATRAC3: LP2/LP4
Modulation system
EFM (Eight to Fourteen Modulation)
Number of channels
2 stereo channels
1 monaural channel
Frequency response
20 to 20,000 Hz ± 3 dB
Outputs
Headphones/earphones: stereo mini-jack,
output level
1 mW + 1 mW load impedance 16 Ω
( )European model
5 mW + 5 mW load impedance 16 Ω
( )Other models
Power requirements
Nickel metal hydride rechargeable battery
One NH-10WM (supplied): 1.2 V,
900 mAh (MIN)
One LR6 (size AA) battery (not supplied)
External power jack (for the battery charging
stand): Power rating 3V DC
Battery operation time
See “When to replace or recharge the battery”
Dimensions
Approx. 73.4 15.3 mm (w/h/d) (3× 80.6 ×
×
3 1/4 × 5/8 in.)
(not including projecting parts and controls)
Mass
Approx. 67 g (2.4 oz) (the player only)
Supplied accessories
Headphones/earphones with a remote control
(1)
Battery charging stand (1)
AC power adaptor (for the supplied battery
charging stand) (1)
Rechargeable battery (1)
Rechargeable battery carrying case (1)
Dry battery case (1)
Carrying pouch (1)
US and foreign patents licensed from Dolby
Laboratories.
Design and specifications are subject to change
without notice.
Optional accessories
AC power adaptor
AC-E30L (for use in Japan), AC-E30HG (for use
outside Japan)
NH-10WM Nickel metal hydride rechargeable
battery
MDR series stereo headphones/earphones*
SRS series Active Speakers
* Whether you should plug the headphones/
earphones directly to the jack on the maini
unit or to a remote control, use only
headphones/earphones with stereo mini
plugs. Headphones/earphones with a
microplug cannot be used.
Your dealer may not handle some of the above
listed accessories. Please ask the dealer for
detailed information about the accessories in
your country.
Parts and controls
The Player
2
3
1
4
5
8
7
9
q;
qa
qs
qd
6
1VOLUME +*, – buttons
2Battery compartment
3
u
*
button
4HOLD (Locking the control) switch
5Terminals for dry battery case (at the
bottom)
6Terminals for charging stand (at the
bottom)
7GROUP button
8Hand strap hole
Use the hole to attach your strap.
9i (headphones/earphones) jack
q; “3-color info-LED”
qa OPEN switch
qs .,
>
button
qd x
button
* VOLUME + and
u
have a tactile dot.
The display window of the remote
control
1 2 3 4 5 6
7 8
1Disc indication
2Track number display
3Character information display
4Group play indication
5Play mode indication
66-band equalizer indications
7Battery level indication
8Bookmark indication
The battery charging stand
B
A
1Terminals for charging
2DC IN 3V jack (at the bottom)
The headphones/earphones with a
remote control
8
9
qa
qs
7
A
B
C
D
5
F
q;
1Headphones/earphones
2Stereo mini plug
3Control VOL +, –
Turn to adjust the volume.
4x (stop) button
5Jog lever (.•
u
/ENT•
>
) button
6 (Group) +, – button
7Clip
8HOLD switch
9Display window
q; DISPLAY button
qa P MODE / (play mode/repeat) button
qs SOUND button
Setting
The backlight lights when you
operate the player or the
remote control, and
automatically turns off when
no operation is made for a
while (factory setting).
The backlight lights while the
player is operating.
The backlight stays off.
Terminal
Terminal
Terminal
Terminal

Produktspezifikationen

Marke: Sony
Kategorie: Nicht kategorisiert
Modell: MZ-E510

Brauchst du Hilfe?

Wenn Sie Hilfe mit Sony MZ-E510 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten


Bedienungsanleitung Nicht kategorisiert Sony

Sony

Sony CKA-NWU10 Bedienungsanleitung

7 Oktober 2024
Sony

Sony BP-GL95 Bedienungsanleitung

2 Oktober 2024
Sony

Sony BP-GL65 Bedienungsanleitung

2 Oktober 2024
Sony

Sony BP-L80S Bedienungsanleitung

2 Oktober 2024
Sony

Sony MUC-M12BL2 Bedienungsanleitung

2 Oktober 2024
Sony

Sony CKS-M10 Bedienungsanleitung

30 September 2024
Sony

Sony Clié PEGA-SA500 Bedienungsanleitung

21 September 2024
Sony

Sony CKS-NWE010 Bedienungsanleitung

20 September 2024
Sony

Sony MSAC-MMDS Bedienungsanleitung

11 September 2024
Sony

Sony VCT-FS7 Bedienungsanleitung

11 September 2024

Bedienungsanleitung Nicht kategorisiert

Neueste Bedienungsanleitung für -Kategorien-

DAS Audio

DAS Audio AX-112-5 Bedienungsanleitung

16 Oktober 2024
Ferplast

Ferplast Ergocomfort Freetime Bedienungsanleitung

16 Oktober 2024
AEG

AEG MECK52 Bedienungsanleitung

16 Oktober 2024
Makita

Makita UR012G Bedienungsanleitung

16 Oktober 2024
Stihl

Stihl HT 70 Bedienungsanleitung

16 Oktober 2024
Ernesto

Ernesto H14270 Bedienungsanleitung

16 Oktober 2024
IFM

IFM AC901S Bedienungsanleitung

16 Oktober 2024
Nedis

Nedis RFPOM120FBK Bedienungsanleitung

16 Oktober 2024
AEG

AEG E9KLCS01 Bedienungsanleitung

16 Oktober 2024
ART

ART ProChannel II Bedienungsanleitung

16 Oktober 2024