Satel MAGENTA Bedienungsanleitung
Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Satel MAGENTA (4 Seiten) in der Kategorie Detektor. Dieser Bedienungsanleitung war für 39 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet
Seite 1/4
MAGENTA
DIGITAL GLASS-BREAK DETECTOR
magenta_en 03/18
The MAGENTA detector enables detection of plate, tempered or laminated glass breaking.
This manual applies to the detector with electronics version 1.1 (or newer).
1. Features
ï‚· Advanced two-path sound analysis.
ï‚· Adjustable detection sensitivity.
ï‚· Supply voltage supervision.
ï‚· LED indicator.
ï‚· Tamper protection against cover removal and tearing enclosure from the wall.
2. Description
Glass-break detection
The detector will report an alarm when it detects a low frequency sound (impact) followed by
a high frequency sound (glass break) in less than 4 seconds. The alarm is signaled by the
alarm output for 2 seconds.
Supply voltage supervision
The detector will report a trouble when the supply voltage drops
below 9 V (±5%) for more than 2 seconds. The trouble results in
turning on the alarm output. The alarm output remains on as
long as the trouble exists.
Electronics board
terminal block:
+12V - power input,
COM - common ground,
TMP - tamper output (NC),
NC - alarm output (NC relay).
tamper contact.
red color LED to indicate:
ï€ detection of low-frequency sound – ON for 0.5 seconds,
ï€ alarm – ON for 2 seconds,
ï€ test mode – short flash every 3 seconds,
ï€ low supply voltage – ON.
detector configuration pins:
TEST – enabling/disabling the test mode. In the test mode,
the detector reports an alarm when it detects a high
frequency sound (glass break sound). The test mode is
enabled when the jumper is set in ON position (Fig. 2).
2 MAGENTA SATEL
LED – enabling/disabling the LED indicator. The LED indicator is enabled when the
jumper is set in ON position (Fig. 3).
potentiometer for the adjustment of detection sensitivity (Fig. 4).
3. Selecting a mounting location
ï‚· The detector is designed for indoor installation.
ï‚· The detector microphone should be directed towards the protected glass, so the best
place to mount the detector is the wall opposite the protected glass.
ï‚· The distance between the detector and the protected glass must not exceed the detection
range (6 m).
ï‚· There must be no objects between the detector and the glass.
ï‚· The detection range depends on the room acoustics. The shades, curtains, furniture
upholstery, acoustic tiles, etc. absorb the sound and adversely affect the detector
operating range.
ï‚· Do not mount the detector on the same wall as the protected glass.
4. Range test
Check that the detector located in the selected installation location can detect the glass-
break. A temporary 12 V DC power supply will be needed for the test.
1. Open the detector enclosure (Fig. 7).
2. Make an opening for the wires in the enclosure base.
SATEL MAGENTA 3
3. Run wires through the prepared opening to a temporary 12 V DC power source.
4. Connect the power wires to the +12V and COM terminals.
5. Place the jumper on the TEST pins in the ON position (Fig. 2).
6. Close the detector enclosure.
7. Put the detector at the planned installation place.
8. Power up the detector.
9. Place the INDIGO TESTER close to the protected glass and use it to generate a glass-
break sound.
10. If the detector reports an alarm, proceed to the next steps. If the detector fails to report an
alarm, increase sensitivity or select another installation location and repeat the test.
11. Power down the detector.
12. Open the detector enclosure.
13. Disconnect the power wires.
14. Place the jumper on the TEST pins in the OFF position (Fig. 2).
5. Installation
Disconnect power before making any electrical connections.
1. Run wires through the opening prepared earlier.
2. Use screws to secure the enclosure base to the mounting surface (Fig. 9). Wall plugs
(screw anchors) and screws are included in the detector delivery set.
3. Connect the wires to the corresponding terminals on the electronics board.
Produktspezifikationen
Marke: | Satel |
Kategorie: | Detektor |
Modell: | MAGENTA |
Breite: | 26 mm |
Tiefe: | 112 mm |
Gewicht: | 40 g |
Produktfarbe: | Weiß |
Ãœbertragungstechnik: | Kabelgebunden |
Höhe: | 29 mm |
Energiequelle: | AC/DC |
Betriebstemperatur: | -10 - 55 °C |
Relative Luftfeuchtigkeit in Betrieb: | 0 - 93 % |
Distanzerfassung: | 6 m |
Transmissionsdistanz: | - m |
Brauchst du Hilfe?
Wenn Sie Hilfe mit Satel MAGENTA benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten
Bedienungsanleitung Detektor Satel
19 August 2024
18 August 2024
18 August 2024
18 August 2024
17 August 2024
17 August 2024
9 August 2023
Bedienungsanleitung Detektor
- Detektor Nedis
- Detektor Brennenstuhl
- Detektor Voltcraft
- Detektor Bosch
- Detektor Laserliner
- Detektor Velleman
- Detektor Powerfix
- Detektor Maginon
- Detektor Schwaiger
- Detektor Alecto
- Detektor Denver
- Detektor König
- Detektor MarQuant
- Detektor National Geographic
- Detektor Black And Decker
- Detektor Skil
- Detektor Trotec
- Detektor Dometic
- Detektor Pyle
- Detektor Pioneer
- Detektor Abus
- Detektor Elro
- Detektor Olympia
- Detektor Smartwares
- Detektor Ferguson
- Detektor Steinel
- Detektor Garmin
- Detektor Nexa
- Detektor Amprobe
- Detektor GEV
- Detektor Tripp Lite
- Detektor Honeywell
- Detektor B/R/K
- Detektor DURO
- Detektor Silverline
- Detektor IGet
- Detektor Netatmo
- Detektor Techly
- Detektor Ebode
- Detektor Xavax
- Detektor Hager
- Detektor Kyoritsu
- Detektor Safescan
- Detektor JUNG
- Detektor Testo
- Detektor Ei Electronics
- Detektor FireAngel
- Detektor Edimax
- Detektor Optex
- Detektor V-TAC
- Detektor Uniden
- Detektor Genie
- Detektor Royal Sovereign
- Detektor Siedle
- Detektor Grothe
- Detektor Cobra
- Detektor EVOLVEO
- Detektor Busch-Jaeger
- Detektor Testboy
- Detektor Multimetrix
- Detektor Extech
- Detektor Sun Joe
- Detektor Fluke
- Detektor Hikvision
- Detektor Soler & Palau
- Detektor FLIR
- Detektor Garrett
- Detektor Vemer
- Detektor Homematic IP
- Detektor Ferrex
- Detektor Gamma Scout
- Detektor Joy-it
- Detektor Mercury
- Detektor PCE Instruments
- Detektor Sanwa
- Detektor X-Sense
- Detektor X4-Tech
- Detektor Vimar
- Detektor ZKTeco
- Detektor Dahua Technology
- Detektor AcuRite
- Detektor Inovonics
- Detektor Pentatech
- Detektor HT Instruments
- Detektor FireX
- Detektor Beha-Amprobe
- Detektor Escort
- Detektor System Sensor
- Detektor Axis
- Detektor Fire-Lite
- Detektor ORNO
- Detektor BlendMount
- Detektor Zircon
- Detektor Kreator
- Detektor Cavius
- Detektor DSC
- Detektor STI
- Detektor Popp
- Detektor Schabus
- Detektor SureCall
- Detektor Minelab
- Detektor Gewiss
- Detektor Fisher
- Detektor Silent Knight
- Detektor Seco-Larm
- Detektor S.E. International
- Detektor BeeSecure
- Detektor Skyscan
- Detektor Thitronik
- Detektor AngelEye
- Detektor Guardian Avionics
- Detektor Whistler
- Detektor Flow Smoke Detector
- Detektor Benewake
- Detektor Resideo
- Detektor K40
- Detektor Rocky Mountain
- Detektor Bearware
- Detektor Winland
- Detektor Noyafa
Neueste Bedienungsanleitung für -Kategorien-
4 Oktober 2024
1 Oktober 2024
22 September 2024
14 September 2024
12 September 2024
12 September 2024
12 September 2024
6 September 2024
6 September 2024
6 September 2024