Sanyo LNS-M02 Bedienungsanleitung


Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Sanyo LNS-M02 (6 Seiten) in der Kategorie Projektorzubehör. Dieser Bedienungsanleitung war für 11 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/6
LCD PROJECTOR LENS
MODEL NO. LNS-S04/LNS-M02
LENS REPLACEMENT
AND INSTALLATION PROCEDURES
NOTES ON REPLACEMENT AND INSTALLATION
The procedures and the needed pars for lens installation depend on the type of
cabinet. Before installing or replacing the lens, make sure the type of cabinet and be
sure to refer to the Installations corresponding with your projector.
When installing or replacing the lens, make sure the Lens Model No. matches with
your projector. Refer to the catalog, or contact your sales dealer for the proper Lens
Model No.
TYPE OF THE CABINET AND INSTALLATION PROCEDURES
Refer to the Installation procedure corresponding to your projector and install the lens
correctly. (See the chart below.)
1AA6P1P5925-- (IFTT)
For use the other models (other than above cabinet), contact your sales dealer.
Printed in Japan
Some parts are not used for installation or replacement. Keep these parts for later use.
Note : Figures in this manual may be differ from the actual product.
After installing or replacing the lens, be sure to check the following for safety.
1. Check the lens is securely fixed.
2. Check no part is missing, or no mounting part is loose.
BE SURE TO CHECK FOR SAFETY
-1-
LIST OF CONTENTS
Following parts are included in the packing.
LENS 1 pc.
LENS CAP Front and rear (Each 1 pc.)
SCREW DRIVER 1 pc.
INSTALLATION MANUAL 1 pc.
Lens installation and replacement should be performed by the qualified
service personnel.
It should be followed by this procedure precisely.
Before attempt to replace the lens, confirm the model number (both the
LCD projector and the lens) and use the proper lens.
The lens cover is on the lens for protection. Be sure to remove the lens
cover before installation.
When installing or removing the lens, be careful not to stain, scratch or
damage the lens.
When shipping the projector with the lens, remove the lens before shipping
the projector.
If you have any questions, contact the dealers.
Notes on Lens Installation and Replacement
-2-
Turn the Lens Mount Cover counter-clockwise
and take it off by pulling forward. (See Fig. 1)
Fig. 1
Lens Mount Cover
A
Fig. 2
B
A
B
Remove 2 Screws and loosen 2 Screws . A B
Slide the Top Cover forward to take off.
(See Fig. 2)
Top Cover
Turn off the projector, press the Main On/Off
Switch to Off and unplug the AC power cord
from the AC outlet.
Remove the Cover Plate by lifting upwards.
(See Fig. 3)
Fig. 3
Cover Plate
This projector can use three (3) different types
of Light-Block Plates, use the Light-Block Plate
that corresponds to the appropriate optional
lens.
NOTE:
The Light-Block Plate FK2A is separated to the
upper and lower plates.
Lower Plate
Upper Plate
DOWN
UP
Insert the lower Light-Block Plate.
(See Fig. 4.)
Fig. 4
LENS REPLACEMENT AND INSTALLATION PROCEDURE
1
2
3
4
5
6
NOTE:
Make sure the shape of the Light-Block Plate
is correct.
Make sure the mark (UP/DOWN and FRONT/
BACK) on Light-Block Plates are correct and
set them properly.
Use the following Light-Block Plate.
Light-Block Plate
Type FK2A
(610 337 0064)


Produktspezifikationen

Marke: Sanyo
Kategorie: Projektorzubehör
Modell: LNS-M02

Brauchst du Hilfe?

Wenn Sie Hilfe mit Sanyo LNS-M02 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Projektorzubehör Sanyo

Bedienungsanleitung Projektorzubehör

Neueste Bedienungsanleitung für -Kategorien-