SAB Heli Division Head HPS3 - H0490-K Goblin 570 Bedienungsanleitung

SAB Heli Division Modellbau Head HPS3 - H0490-K Goblin 570

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für SAB Heli Division Head HPS3 - H0490-K Goblin 570 (2 Seiten) in der Kategorie Modellbau. Dieser Bedienungsanleitung war für 9 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF

Seite 1/2

Spindle

(H0471-S)

Main Blade Grip Assembly ....x2

Note

Large ID Inside

Button Head Cap

Screw M6x10mm

(HC122-S)

Oring

(HC353-S)

Washer

12x1mm

(HC193-S)

Washer

11x

13.8x0.5mm

(H0226-S)

Thrust Bearing

14x4mm

(HC437-S)

Center Hub Assembly

Radius Arm

(H0474-S)

Socket Shouder

M4x24mm

(HC111-S)

Flanged Bearing

7x3mm

(HC402-S)

Flanged Bearing

2.5x

6x2.5mm

(HC400-S)

Spacer

(H0134-S)

Main Blade Grip

Assembly

Bearing

14x4mm

(HC417-S)

Approx. 62.5mm

Radius Arm

Assembly ... x 2

Uniball M3

(H0063-S)

Swashplate

Assemly

(H0475-S)

Uniball

(H0065-S)

Linkage Rod A Assembly . . . .x3

Linkage Rod A

Assembly

(After a few flights, please check the preload

you can add HC228 if the preload has changed.)

(Initial length for the rods from the

swashplate to the Blade Grip.)

(to adjust the tracking,

turn this linkage.)

H0489M_Rev01

Socket Head Cap

Screw M3x12mm

(HC062-S)

Pin 4 mm

(H0472-S)

Socket Head Cap

Screw M2.5x5mm

(HC017-S)

Uniball M3

(H0065-S)

Socket Head Cap

Screw M3x8mm

(HC050-S)

[H0225-S]

Socket Head Cap

Screw M2.5x8mm

(HC022-S)

Spacer Arm

(H0416-S)

Flanged Bearing

2.5x

6x2.5mm

(HC400-S)

Radius Arm

Assembly

Swashplate Assemly

Uniball Radius Arm

(H0415-S)

Socket Head Cap

Screw M2.5x8mm

(HC022-S)

Socket Head Cap

Screw M3x12mm

(HC062-S)

Radius Arm

Assembly

Spacer

(HC176-S)

M3x20mm

[HC082-S]

M3x12mm

[HC062-S]

Nut M3

[HC206-S]

[HC176-S]

Please read this user manual carefully, it contains instructions for the correct assembly of the KIT.

Please refer to the website www.goblin-helicopter.com for updates and other important information. Thanks You.

Metrix Head

Nylon Nut M4

(HC212-S)

Blade

Washes

(H0265-S)

eg: Microlube GL261

Flanged Bearing

7x3mm

(HC402-S)

Center Hub

(H0473-S)

Damper

(H0425-S)

Uniball M3

(H0065-S)

Note:

Please add thread

locker to the M6x10 screws

Approx

52.5mm

Plastic Ball Link

(H0066-S)

Plastic Ball Link

(H0066-S)

Linkage Rod M2.5x33mm

(H0237-S)

Bearing

14x4mm

(HC417-S)

Main Blade Grip

(H0202-S)

[HC228-S]

Page 1

HPS3 ROTOR HEAD

[

H0489-K Goblin 500, H0490-K Goblin 570

]

Swashplate

[H0475-S]

- 1 x Swashplate Assembly.

- 1 x Bearings 30x

37x4mm.

- 6 x Uniballs M3x4

5 H3.

- 1 x Uniball M3x4

5 H18.

- 7 x Socket Head Cap Screws M2x5mm.

- 3 x Swasher

5x0.5mm

Radius Arm

[H0474-S]

- 1 x Center Hub.

- 1 x Socket Head Cap Screws

M3x12mm.

- 1 x Socket Head Cap Screw

Shouldered M3x20mm.

- 1 x Metric Hex Nylon Nut M3.

Center Hub

[H0473-S]

- 2 x Radius Arms.

- 2 x Spacer Arm

- 1 x Spacer Hex.

- 1 x Uniball Radius Arms.

- 2 x Socket Head Cap Screws M3x12mm.

- 2 x Socket Head Cap Screws M2.5x8mm.

- 2 x Flanged Bearings

2.5x

6x2.5mm.

- 4 x Flanged Bearings

7x3mm.

Linkage

[H0237-S]

- 2 x Linkages M2.5x33mm.

- 4 x Plastic Ball Links.

Damper Derlin

[H0425-S]

- 2 x H0425.

- 2 x Orings.

- 4 x Steel Shims Ø8xØ14x0,2mm.

Recommendations

- These parts should be used only with models SAB Goblin

- Please follow all the instructions shown in the Goblin main manual. In this manual please read Chapther 2, Important notes

- Use Loctite on all threads.

- Put a small amount of grease inside the hub and the O-Ring.

- Check for axial play of the spindle at least after the first 10 flights and add shims if necessary.

- Firmly tighten the blades before flight.

About HPS

HPS stands for "High Precision System". This head has been

developed in order to increase the usable rotor RPM range without

having to change the rigidity of the dampening system.

The new head is developed specially to limit the teetering effect of

the spindle by means of dampening achieved by a special

technopolymer material.

The maximum teetering amount can be adjusted based on the

amount of play shown in figure "A" of the drawing. The O-ring is

necessary to create a radial and axial preload.

The preload can be kept relatively low, thanks to the mechanical

locking properties of the technopolymer dampeners.

With this solution, finding the correct preload is less complex.

This solution is safer because there is a physical "stop" of the

teetering effect with the technopolymer dampers, also with low

axial preload.

The change of preload will serve exclusively to customize the

response of the model.

Furthermore, the spindle can only move vertically thanks to the

elongated hole shown in section "B" of the drawing.

This solution allows an optimal control of the geometry even when

large amounts of torque are introduced into the system.

The head is very accurate and reliable.

Spare Parts

- 2 x Main Blade Grip.

- 2 x

Thrust Bearing

14x4mm.

- 4 x

Bearing

14x4mm.

- 2 x Washer

11x

13.8x0.5mm.

Blade Grip

[H0202-S]

- 2 x Blade Grip Arm.

- 2 x Socket Head Cap

Screw M3x8mm.

- 2 x Uniball M3.

Blade Grip Arm

[H0203-S]

Spindle Shaft

[H0471-S]

- 2 x Spindle Shaft.

- 2 x Pin 4mm.

- 4 x Socket Head Cap M2x5mm.

- 2 x Socket Head Cap

M6x10mm.

- 2 x Washer Ø8xØ10.2x0.5mm.

ABOUT HPS3

For safety reasons we suggest to not exceed.

2500 rpm Goblin 500

2400 rpm Goblin 570

In the KIT, you will find a bigger tail blades. This size is optimazed for

to counteract the additional torque in troduced by 3rd rotor blade.

TIPS:

Left Side

Right Side

* To remove the dampeners, you

can use a flathead screwdriver

through the hole as shown.

* Clock-wise, counter clock-wise thread

* By turning the linkages you can adjust

tracking.

SPARE PARTS

RECOMMENDATIONS

These parts should be used only with models SAB Goblin.

· Goblin 500 (recommended blades SAB 3BL465, max 500 mm)

· Goblin 570 (recommended blades SAB 3BL540, max 550 mm)

- 3 blades rotor head requires a much lower cyclic gain on

flybarless systems.

We recommend that you set your gain at least 30% lower than the gain

you normally use on your 2 blade rotor head helicopters.

You can start increasing the gain after you complete your first flight.

Running too high of a gain can induce a violent oscillation that can

potentially cause damage to your helicopter in flight.

- Please follow all the instructions shown in the Goblin main manual.

In this manual please read Chapter 2, Important notes

- Use Loctite on all threads.

- Put a small amount of grease inside the hub and the O-Ring.

- Check the spindle for axial play at least after the first few flights and add

shims as necessary, slight axial preload is optimal.The blade grips must

move freely, but they should not move just under their own weight.

- Firmly tighten the blades before flight.

Detail B

Goblin 500 = Tail Blade BW5095

Goblin 570 = Tail Blade BW5104

Page 2

HPS3 ROTOR HEAD

[

H0489-K Goblin 500, H0490-K Goblin 570

]

Produktspezifikationen

Marke:	SAB Heli Division
Kategorie:	Modellbau
Modell:	Head HPS3 - H0490-K Goblin 570

Brauchst du Hilfe?

Wenn Sie Hilfe mit SAB Heli Division Head HPS3 - H0490-K Goblin 570 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten

Ihren Namen*

Deine E-Mail*

Schreiben Sie hier Ihre Frage