Pyle PBT30M Bedienungsanleitung

Pyle Kopfhörer PBT30M

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Pyle PBT30M (2 Seiten) in der Kategorie Kopfhörer. Dieser Bedienungsanleitung war für 3 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF
Seite 1/2
200.00 mm
270.00 mm
2
5
6
Headset pictures..........................................................................................................1
Charging the battery.....................................................................................................1
Turning on the Headset.................................................................................................1
Turning off the Headset.................................................................................................1
Headset in Pairing Mode...............................................................................................2
Establishing Bluetooth Link...........................................................................................3
Answering incoming calls..............................................................................................3
Transferring calls.........................................................................................................4
Muting the microphone.................................................................................................4
Ending calls.................................................................................................................4
To make a new call using v oice d ial................................................................................4
Redialing last dialed number.........................................................................................5
Reject a call.................................................................................................................5
Adjusting speaker volume.............................................................................................5
To wear the headset.....................................................................................................5
Low-battery indication..................................................................................................6
Battery recharging........................................................................................................6
LED Status..................................................................................................................7
Voice Over Internet Protocol (VoIP) Application..............................................................8
FCC Interference statement ........................................................................................9
Declaration of Conformity..........................................................................................11
● Charging the battery
Thank you for buying the new PBT30M Headset with Bluetooth wireless technology. Before
first time use, it is important to charge the battery for 8 hours.
● Turning on the Headset
While the Headset is powered down, press and hold S1 until blue LED turns on. A low tone
followed by a high tone will indicate that the PBT30M is powered up. Afterward, blue LED
will flash every 3 seconds.
● Turning off the Headset
While the Headset is powered up, press and hold S1 until red LED turns on. A high tone
followed by a low tone will indicate that the PBT30M is powered down.
Microphone
Speaker
On Off S1/ ( )
Volume Up (S2)
Volume Down S3 ( )
LED
DC Socket
1
Redialing las t dialed number (Mo bile pho nes wit h Handsfre e pr ofi les o nly )
To redial th e last numbe r, pre ss a nd ho ld S3 u ntil 4 to nes are h eard. I t ind ic ate s the red ial
is active.
Reject a cal l (Mobil e phone s with Hands free pr ofile s onl y )
To reject a call at t he t ime t he PB T3 0M rings, press and hold S 1 un til y ou hear 2 t one s.
Adjustin g Spe aker Volume:
When a call i s ongoing , pressing and r eleasing S 2 will increa se the speaker volume and
pressing and releasing S3 will decrease the speaker volume on the He ad set . There is a
key ton e to indic ate volume i ncr eas e or decrease. However, a wa rning tone wil l be he ard
when the vol ume l ev el re ac hes i ts maximum o r minimum.
To wear the head set
Make sure th e mic ro phone is poi nting towa rd s you r mou th.
Transferring Calls (For Nokia 3650 or equivalent models)
When you are in session, calls can be transferred from the Bluetooth phone to the HS and from
the HS to the Bluetooth phone.
To transfer a call from the Bluetooth phone to the HS: press S1 once, the call will be
transferred to the HS.
To transfer a call from HS to the Bluetooth phone, please follow the operating instructions of
your phone.
Muting the microphone
To mute the microphone during an active call press both S2 and S3 buttons simultaneously for
about a second and the microphone will be muted. A periodic beep tone will be heard when the
mute function is active.
To end the mute function: When the microphone is muted, press both S2 and S3 buttons
simultaneously. Mute function is ended and the periodic beep tone will stop.
Ending Calls
While a call is in session on the Headset pressing S1 will disconnect the call. After the call is
disconnected, the blue LED will flash normally again.
To make a new call using voice dial
Make sure the voice dialing function is set up in the mobile phone and it is within the range of
the Headset. Press S1 on the PBT30M shortly. There is a beep tone on the headset.Then use
your recorded voice commands ( eg. By saying the name of the person). The call will be
connected in a few seconds.
User Manual
PBT30M
®
Bluetooth Headset
4
3
Headset in Pairing Mode
Ma sure the PBT30M is fully charged and the charging cable is disconnected from it be fore ke
pairing starts. Wh ile the PBT30M is po wered off, press and ho ld S1 until red and blue LE Ds
flashing alternately. It indicates that the He adset is in Pa iring Mode.
Follow th e operating instructions for your Bl uetooth mobile phone to st art the pairing pr ocess.
Typically, this has to be done by going to a setup or connect me nu and then selecting the
options to discover Bluetooth devices. Bl uetooth ma y take several seconds to establish a
connection.
Your phone's display sh ould indicate that it has found the “PBT30M” headset and asks if you
want to pair it. You should confirm this. The ph one's display would pr ompt you for a passkey
or PIN. Enter a sequence of “ ”.0000
The headset LED will flash blue every 3 seconds, indicating successful pairing. Us ually the
phone will also ask whether you want to change the headset's na me. We recommend to ke ep
the default name PBT30M instead of changing it.
If pairing does no t occur as ex pected:Turn of f both the headset and the phone and wait for 10
seconds. Turn on the headset and phone again and repeat all steps from beginning. Pairing
does authorize the devices like mobile phones and headsets wi th ea ch other and only needs
to be performed once.
Establishing Bluetooth Link
After successfully pairing the PBT30M and the mobile phone, you may need to establish a Bluetooth
link between them according to the operation manual of your mobile phone. To establish the link, press
S1 shortly. Use Nokia 6130i as an example, the mobile phone will show “Do you accept PBT30M
request for connection?” Select YES to establish the link. You are ready to make and answer calls on
the Headset. For other phones, please follow the operation manual to establish the link. You are ready
to make and answer calls on the Headset.
Please note:
If the headset is powered down, turning on the headset will auto reconnect the last used device. If the
headset is disconnected but powered on, press S1 shortly to connect the link again. If there is
abnormal loss of link happened (e.g. out of range), the headset will automatically try to reconnect the
mobile phone several times.
If the mobile phone cannot locate the network signal (e.g. out of reach) , alert tone will be heard every
5 seconds in the headset.
Not every mobile phone supports no network signal alert feature.
If there is no Bluetooth connection for more than 1 hour, the headset will switch off automatically.
Answering Incoming Calls
When you wear the headset, an incoming call is present, the PBT30M headset will ring. Pressing S1
will answer the call.
Attention: Some phones put the Bluetooth connection into Standby Mode if it has not been used for
some time. When there is phone call in, only the mobile phone rings and it will take a few seconds to
transfer the call to headset. You have to wait until you hear the ring tone in headset. If you press S1 to
take the call before you hear the ring tone in headset, the headset will try to establish Bluetooth
connection. This will cause connection conflicts between mobile phone and headset.
Low-ba ttery indic at ion
The PBT3 0M LED will fla sh r ed instead of b lue when th e ba tt ery is low. There will also a
short be ep period ic ally. After thi s indi cation yo u stil l have up to 15 m in utes talk tim e. Whe n
the batt ery level is too low, the Heads et w ill autom at ic ally power off. I t ca nnot be powered o n
again un less the ch arger is connecte d or the battery is s ufficiently charged.
Battery rechargin g
To recha rge the bat te ry, put t he h eadset on pho ne holder. Dur in g recharg ing, the LED
shows a steady red li ght.
When the battery is f ul ly c harged, t he i ndicato rs o f re d light wil l be off .
The achi evable ta lk t ime and stand by time for the PBT30 M can vary with d iffe rent Blueto oth
mobile phones due to different imple mentation o f po wer down modes.
Keep the headset away from fire to avo id damage.
(1) A/C cha rging (2) Car charging
Note
Material 80g Woodfree Paper:
1
2
3
4
5
6
7
8
AB C D E
AB C E
1
2
3
4
5
6
7
8
D
PART NO .:
MCB-8127020-1A
MODEL:
8127
DRAWN:
Limingzan
DATE:
20071204
PAPER SIZE :
A3
UNIT:
MM
SCALE:
: 1 1
:DESCRIPTION
#User Manual For PYLE Logo
In Tech Electronics Ltd- .
Reminding:
- For safety reason, please don't leave the headset in car alone when charging.
- When the battery is low, the LED will not turn on until the headset is charged up, which may
take s everal minutes.
● Led Status
10
9
128
7
LED
1 x 3 sec. Blue
1 x 1 sec. Blue
Blinking red
Red LED on
Red LED off
Red/Blue Blinking
Status
Ready can be accessed by paired devices
Talking
Battery low (max. 15 Minutes left)
Under charging
Fully charged
Pairing-Mode
PBT30M
11
FCC Caution: Any changes or modifications not expressly approved by the party responsible
for compliance could void the user's authority to operate this equipment.
IMPORTANT NOTE:
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment. End users must follow the s pecific operating instructions for satisfying RF
exposure compliance.
This transmitter must not be co-located or operating in conjunction with any other antenna or
transmitter.
FCC ID:NV6-CS8127
Federal Communication Commission
Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequenc y energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one of the
following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
-Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subjec t to the following two
conditions: (1)This device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation.
USB Dongle and PBT30M Bluetooth Headset
Voice Over Internet Protocol (VoIP) Application
Install Software for Bluetooth USB Dongle from the CD-ROM provided in the USB Dongle
package. Note that the CD-ROM is not available in the PBT30M package.
Plug the USB Bluetooth Dongle (purchased separately) into the USB socket of a PC.
Download from the corresponding websites and install Skype, MSN messenger,Netmeeting,
Yahoo messenger, or ICQ application software in the PC.
Pairing: Put the PBT30M Bluetooth Headset into "pairing" mode. Start the Bluetooth software
and pair the USB Dongle with the PBT30M Headset. The Headset passkey is " ".0000
Connecting and Disconnecting: To connect the USB dongle, press the S1 key on the Headset.
To disconnect the Bluetooth link, press the S1 key again.After turn off and turn on the headset,
you just need to press S1 key to establish the audio link with USB dongle if the USB dongle
is the last used device.
Testing the Bluetooth Link: After the USB Dongle is connec t with the PBT30M Headset, the PC
audio will be automatically routed to the "Bluetooth Audio" driver. Play some music on the PC
by Windows Media Player or other mus ic applications; you should be able to hear the music
on the Headset. If you can't hear it, then go the "control Panel " ->" Sound and Audio Device
Properties"-> "Audio"-> "Sound playback" select the "Bluetooth Audio" to activate the link.
Now you can start using the VoIP application and talk to your friend through your Headset
wirelessly and freely.
Connecting PBT30M Bluetooth Headset back to your Bluetooth mobile phone. Please follow
the steps from 'Headset in Pairing Mode' to 'Establishing Bluetooth Link'.
The following company is responsible for this declaration:
Sound Around Inc.
1600 63rd Street
Brooklyn N.Y. 11204,
USA
Phone: 1-800-444-5671 718-535-1800
Fax: 718-236-2400
Bluetooth Qualified Design ID: B013218
Sound Around Inc.
En vironmenta l
fr iend ly
Note
Material 80g Woodfree Paper:
1
2
3
4
5
6
7
8
AB C D E
AB C E
1
2
3
4
5
6
7
8
D
PART NO .:
MCB-8127020-1A
MODEL:
8127
DRAWN:
Limingzan
DATE:
20071204
PAPER SIZE :
A3
UNIT:
MM
SCALE:
: 1 1
:DESCRIPTION
#User Manual For PYLE Logo
In Tech Electr onics Ltd- .

Produktspezifikationen

Marke: Pyle
Kategorie: Kopfhörer
Modell: PBT30M

Brauchst du Hilfe?

Wenn Sie Hilfe mit Pyle PBT30M benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten


Bedienungsanleitung Kopfhörer Pyle

Pyle

Pyle PHPNC65 Bedienungsanleitung

15 August 2024
Pyle

Pyle PLVWH6 Bedienungsanleitung

6 August 2024
Pyle

Pyle PHPW5 Bedienungsanleitung

5 August 2024
Pyle

Pyle PSWBT550.9 Bedienungsanleitung

5 August 2024
Pyle

Pyle PWBH18 Bedienungsanleitung

31 Juli 2024
Pyle

Pyle PGPHONE80 Bedienungsanleitung

30 Juli 2024
Pyle

Pyle PHPNC85 Bedienungsanleitung

23 Juli 2024
Pyle

Pyle UPSWP14BK Bedienungsanleitung

23 Juli 2024
Pyle

Pyle PHPW2 Bedienungsanleitung

22 Juli 2024
Pyle

Pyle PLVWH1 Bedienungsanleitung

21 Juli 2024

Bedienungsanleitung Kopfhörer

Neueste Bedienungsanleitung für -Kategorien-

AKG

AKG K920 AFC Bedienungsanleitung

16 Oktober 2024
GoGEN

GoGEN HBTM 41WR Bedienungsanleitung

16 Oktober 2024
Nedis

Nedis HPBT2102BK Bedienungsanleitung

15 Oktober 2024
AKG

AKG Y600NC Bedienungsanleitung

15 Oktober 2024
Vakoss

Vakoss MH954 Bedienungsanleitung

14 Oktober 2024
Skullcandy

Skullcandy Cassette Bedienungsanleitung

14 Oktober 2024
Audio-Technica

Audio-Technica ATH-ANC29 Bedienungsanleitung

14 Oktober 2024
Daewoo

Daewoo AVS1421 Bedienungsanleitung

14 Oktober 2024
Vakoss

Vakoss MH942 Bedienungsanleitung

14 Oktober 2024
Philips

Philips SHB7150 Bedienungsanleitung

13 Oktober 2024