Posiflex MR-2100 Bedienungsanleitung


Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Posiflex MR-2100 (2 Seiten) in der Kategorie Nicht kategorisiert. Dieser Bedienungsanleitung war für 20 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/2
Page 1 / 2
MR-2100/2200 SERIES
MAGNETIC STRIPE READER
USER’S MANUAL
Rev. : Original
I. FEATURES
Dual directional operation.
Convenient operation dual side swipe design (MR-2200).
Built-in Magnetic Stripe Reader Triple tracks.
Built-in keyboard wedge interface or RS-232 interface or USB interface.
Built-in decoder
Heavy duty die cast case
3 tracks type MSR can read also AAMVA and CA DMV card
FCC NOTICE
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions manual,
may cause interference to radio communications. It has been tested and found to comply with limits for a Class A digital device pursuant to subpart J of Part
15 of FCC Rules, which are designed to provide reasonable protection against interference when operated in a commercial environment. Operation of this
equipment in a residential area is likely to cause interference in which case the user at his own expense will be required to take whatever measures to correct
the interference.
WARRANTY LIMITS
Warranty will terminate automatically when the equipment is opened by any person other than the authorized technicians. The user should consult
his/her dealer for the problem happened. Warranty voids if the user does not follow the instructions in application of this merchandise. The manufacturer is by
no means responsible for any damage or hazard caused by improper application.
The hardware utility program, including instructions for its use, is provided “AS IS” without warranty of any kind. Posiflex Technology, Inc. further
disclaims all implied warranties including without limitation any implied warranties of merchantability or of fitness for a particular purpose. The entire risk
arising out of the use or performance of the software and documentation remains with you.
ABOUT THIS MANUAL
This manual is written in an attempt with full strength to assist the user to utilize the stand-alone magnetic stripe reader MR2100/MR2200 series of
Posiflex POS products. This series of products provide excellent flexibility and reliability in application. This manual covers both operational and technical
aspects of these units.
The manufacturer of the MR2100/2200 series heartily apologizes to the user for reserving the right to change or to modify this manual without
notice due to the rapid and constant progress and improvement on science and technology. The user may always obtain the most up to date information
through any of our web sites: http://www.posiflex.com or http://www.posiflex.com.tw or http://www.posiflexusa.com.
Copyright Posiflex Technology, Inc. 2011
All rights are strictly reserved. No part of this documentation may be reproduced, stored in a retrieval system, or transmitted in any form or by any
means, electronic, mechanical, photocopying, or otherwise, without the prior written consent of Posiflex Technology, Inc. the publisher of this documentation
TRADE MARKS AND SERVICE MARKS
POSIFLEX is a registered trademark of Posiflex Technology, Inc. an ISO-9001 and ISO-14001 certified manufacturer.
Other brand and product names are trademarks and registered trademarks and service marks of their respective owners.
II. MODEL IDENTIFICATIONS
Models
Application MR2100 MR2100-JIS2
MR2200
Interface USB or RS232 or PS2
USB or RS232
USB or RS232 or PS2
Reader Head ISO Single Head JIS2 ISO Dual Side Head
III. SPECIFICATIONS
Reader specification
Applicable card type
ISO 7811 JIS X 6302
Card feed method
Manual
Card feed direction
Bi-direction
Read / write function
Read only
Card feed speed 5 to 55 inches/sec. 100 ~ 1200 mm/sec.
Error rate Less than 0.5% Less than 0.1%
Card data format
Data standard IATA ABA THRIFT
JIS I JIS II
Track used Track 1
Track 2
Track 3
(Track 2)
Rear side
Applicable to
models MR2100-MR2200 MR2100-JIS2
Recording method
F
2
F (FM)
Recording density
210 BPI
75 BPI 210 BPI
75 BPI 210 BPI
Recording capacity
characters / bits 79 / 7 40 / 5 107 / 5
40 / 5 72 / 7
Note: AAMVA CA DMV and standards are supported in 3 track ISO models
Dimensions: 14.5 cm (L) X 4.6 cm (W) X 3.4 cm (H)
Weight: 490 gm
LED: dual color -- green for good read or ready to read
red for invalid read
Rated voltage: 5 VDC
Rated current: 100 mA max.
P/N: 19030901010
T314
54
Page 2 / 2
IV. CABLE CONNECTION GUIDE
Cable connection for KB WEDGE models
Cable connection for RS232 interface models
Cable connection for USB interface models
V. ADJUSTABLE PARAMETERS
Some parameters in readout format of the MR2100/MR2200 series in PS/2 KB interface and USB
interface can be controlled by software downloaded from our web site: http://www.posiflex.com.
However, PS/2 and USB model are automatically saved parameters even after power off and on. It is also
possible to adjust some parameters with modification in hardware described below if not by software.
Please note that the individual track enable mentioned applies only when the track is supported in
physical reader head.
For ISO & JIS2 in USB Mode Jumper Setting
(1). P2 : Connected to USB Cable
(2). CN3 : ISP(Update MCU Firmware)
(3). CN4 / CN5 : Magnetic Stripe Reader ISO
(Use in "USB KB mode" or HID mode")
(4). CN4 / CN5 : Magnetic Stripe Reader JIS2
(Only use in "USB KB mode")
Jumper Setting:
Jumper
Position J1 J2 J3 J4
Function ALT-Num NumLock USB Class Boot protocol
Opened Enable Send Numlock Key
Code
Vendor Class for Linux
or WinCE
Boot protocol for DOS
6.22
Closed Disable N/A HID Class for Windows
Non-Boot protocol for
Windows
Default Close Close Close Close
For ISO in PS2 & RS232 Mode Jumper Setting
For RS232 Mode:
(1). P1 : Not connected.
(2). P2 : Cable Connected to MB(Com Port) &
Power: 5V.
(3). CN3 : ISP(Update MCU Firmware)
(4). CN4/CN5: Magnetic Stripe Reader/JIS2 ISO
Jumper Setting:
Jumper J1 J2 J3 J4 J5 J6 JP1 JP2
Function
Alt-Num
Lead/
End Code
PS2/
RS232
Trk1 Trk2 Trk3 Header2x2
RS232
Header2x2
PS2
Opened Enable
Enable PS2 Disable
Disable
Disable
Closed Disable
Disable RS232
Enable
Enable
Enable
Default CLOSE
CLOSE OPEN
Note: RS232 Mode must be closed J3, JP1; Opened JP2.
For PS2 Mode:
(1). P1 : Connected to PC(PS2-KB Port)
(2). P2 : Connected to Keyboard
(3). CN3: ISP (Update MCU Firmware)
(4). CN4/CN5: Magnetic Stripe Reader ISO
Jumper Setting:
Jumper J1 J2 J3 J4 J5 J6 JP1 JP2
Function
Alt-Num
Lead/
End Code
PS2/
RS232
Reserve
Reserve
PS2 Pin
Switch
Header2x2
RS232
Header2x2
PS2
Opened Enable
Enable PS2
Closed Disable
Disable RS232
Default OPEN
OPEN
OPEN CLOSE
Note: PS2 Mode must be opened J3, J6, JP1; closed JP2
MR2100/MR2200 PC
Keyboard
PC
Mini DIN 6 P Male
Mini DIN 6 P Female
KB I/P
PC USB port or USB hub
MR2
1
00
/MR2200
MR2100/MR2200
2.5/5.5 DC plug from power adaptor
D sub 9 P Female
to COM port


Produktspezifikationen

Marke: Posiflex
Kategorie: Nicht kategorisiert
Modell: MR-2100

Brauchst du Hilfe?

Wenn Sie Hilfe mit Posiflex MR-2100 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Nicht kategorisiert Posiflex

Bedienungsanleitung Nicht kategorisiert

Neueste Bedienungsanleitung für -Kategorien-