Posiflex MR-2000U Bedienungsanleitung


Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Posiflex MR-2000U (2 Seiten) in der Kategorie Nicht kategorisiert. Dieser Bedienungsanleitung war für 9 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/2
Page 1 2 /
MR-2000 Series
MAGNETIC STRIPE READER
USER’S MANUAL
Rev. : C
I. FEATURES
l Double or triple tracks as indicated in MODEL IDENTIFICATION
l Built- -in keyboard wedge interface or RS 232 interface or USB interface as indicated in
MODEL IDENTIFICATION
l Built-in decoder
l Dual directional operation
l Interface cable included
l Heavy duty die cast case
l 3 tracks type MSR can read also AAMVA and CA DMV card
FCC NOTICE
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions manual,
may cause interference to radio communications. It has been tested and found to comply with limits for a Class A digital device pursuant to subpart J of Part
15 of FCC Rules, which are designed to provide reasonable protection against interference when operated in a commercial environment. Operation of this
equipment in a residential area is likely to cause interference in which case the user at his own expense will be required to take whatever measures to correct
the interference.
WARRANTY LIMITS
Warranty will terminate automatically when the equipment is opened by any person other than the authorized technicians. The user should consult
his/her dealer for the problem happened. Warranty voids if the user does not follow the instructions in application of this merchandise. The manufacturer is by
no means responsible for any damage or hazard caused by improper application.
The hardware utility program, including instructions for its use, is provided AS IS” without warranty of any kind. Posiflex Technologies, Inc.
further disclaims all implied warranties including without limitation any implied warranties of merchantability or of fitness for a particular purpose. The entire
risk arising out of the use or performance of the software and documentation remains with you.
ABOUT THIS MANUAL
This manual is written in an attempt with full strength to assist the user to utilize the stand-alone magnetic stripe reader MR2000 series of Posiflex
POS products. This series of products provide excellent flexibility and reliability in application. This manual covers both operational and technical aspects of
these units.
The manufacturer of the MR2000 series heartily apologizes to the user for reserving the right to change or to modify this manual without notice due
to the rapid and constant progress and improvement on science and technology. The user may always obtain the most up to date information through any of
our web sites: http://www.posiflex.com or http://www.posiflex.com.tw or http://www.posiflexusa.com.
Copyright Posiflex Technologies, Inc. 2009
All rights are strictly reserved. No part of this documentation may be reproduced, stored in a retrieval system, or transmitted in any form or by any
means, electronic, mechanical, photocopying, or otherwise, without the prior written consent of Posiflex Technologies, Inc. the publisher of this
documentation
TRADE MARKS AND SERVICE MARKS
POSIFLEX is a registered trademark of Posiflex Technologies, Inc. an ISO- - turer.9001 and ISO 14001 certified manufac
Other brand and product names are trademarks and registered trademarks and service marks of their respective owners.
II. MODEL IDENTIFICATIONS
Interface
Applicable tracks PS/2 KB wedge
RS232 USB
ISO track 1 & 2 MR2000-2 MR2000R-2 MR2000U-2
ISO track 2 & 3 MR2000-2/3 MR2000R-2/3 MR2000U-2/3
ISO track 1 & 2 MR2000-3 MR2000R-3 MR2000U-3
JIS track I & II MR2000-JIS (N. A.) (N. A.)
III. SPECIFICATIONS
l Reader specification
Applicable card type
ISO 7811 JIS X 6302
Card feed method
Manual
Card feed direction
Bi-direction
Read / write function
Read only
Card feed speed 5 to 55 inches/sec. 100 ~ 1200 mm/sec.
Error rate Less than 0.5% Less than 0.1%
l Card data format
Data standard IATA ABA THRIFT
JIS I JIS II
Track used Track 1
Track 2
Track 3
(Track 2)
Rear side
Applicable to
models
MR2000-2, 2/3, 3
MR2000R-2, 2/3, 3
MR2000U-2, 2/3, 3
MR2000-JIS
MR2000U-JIS
Recording method
F2F (FM)
Recording density
210 BPI
75 BPI 210 BPI
75 BPI 210 BPI
Recording capacity
characters / bits 79 / 7 40 / 5 107 / 5
40 / 5 72 / 7
Note 1: AAMVA and CA DMV standards are supported in 3 track ISO models
Note 2: For 2 track ISO readers like MR2000- -2 or MR2000U 2/3 info about the missing track in
above table is not applicable
P/N: 19030900030
警告使用者
是甲產品,在
境 中 使 用 時 , 可 能 會 造 成 射 頻 干
擾, 這種下 使會被
求採取某些適當的對策。
T31454
Page 2 2 /
l Dimensions: 14.5 cm (L) X 4.6 cm (W) X 3.4 cm (H)
l Weight: 490 gm
l LED: dual color -- green for good read or ready to read
red for invalid read
l Rated voltage: 5 VDC
l Rated current: 100 mA max.
IV. CABLE CONNECTION GUIDE
l Cable connection for KB WEDGE models (MR2000-2/3/JIS)
l Cable connection for RS232 interface models (MR2000R-2/3)
l Cable connection for USB interface models (MR2000U-2/3/JIS)
V. ADJUSTABLE PARAMETERS
Some parameters in readout format of the MR-2000 series in PS/2 KB interface and USB interface
can be controlled by software downloaded from our web site: http://www.posiflex.com. However, saved
parameters must be retrieved after power off and on under proper arrangement for the PS/2 KB interface
model while for USB models parameters are automatically saved even after power off and on. It is also
possible to adjust some parameters with modification in hardware described below if not by software.
Please note that the individual track enable mentioned applies only when the track is supported in
physical reader head.
l For MR2000- -2, 2/3, 3 and MR2000R 2, 2/3, 3:
Changing the status of each jumper in the lower dotted area at right that is the enlarged image of
the shaded area on the
control PCB determines
parameters illustrated in
the table below. For
MR2000R-2, 2/3, 3, the
communication protocol
is default at 9600 bps,
none parity, 8 data bits, 1
stop bit.
Table 1
LEADING /
STOP
CODE ALT + NUM
TRACK 1
TRACK 2
TRACK 3
FUNCTION &
JUMPER
STATUS J1 J2 T1 T2 T3
SHORT DISABLED DISABLED
ENABLED
ENABLED
ENABLED
OPEN ENABLED ENABLED
DISABLED
DISABLED
DISABLED
DEFAULT OPEN DEPENDS
SHORT SHORT SHORT
l For MR2000U-2, 2/3, 3
Changing the jumper status on the
control PCB inside die cast case determines
parameters illustrated in the table below.
Table 2
FUNCTION JUMPER SHORT OPEN DEFAULT
LEADING / STOP CODE
J1 DISABLED ENABLED OPEN
ALT + NUM JP2, PIN 1-2
DISABLED ENABLED SHORT
INIT NUM LOCK JP2, PIN 3-4
DISABLED ENABLED SHORT
CLASS JP2, PIN 7-8
HID VENDOR SHORT
OS JP2, PIN 9-10
WINDOWS / LINUX
DOS SHORT
TRACK 1 T1 ENABLED DISABLED SHORT
TRACK 2 T2 ENABLED DISABLED SHORT
TRACK 3 T3 ENABLED DISABLED SHORT
Note 1: To use the USB interface MSR in operating system without USB support, please set USB
keyboard enabled in BIOS (CMOS) setup.
Note 2: Since this USB interface MSR works as a USB keyboard which is a normal HID (Human
Interface Devices) in USB classification, no special driver shall be required. However, it
should be set as vendor class for Linux system and special driver is required.
MR2000-2, 2/3, 3, JIS
PC
Keyboard
PC
Mini DIN 6 P Male
Mini DIN 6 P Female
KB I/P
PC USB port or USB hub
MR2000U
-
2. 2/3, 3, JIS
MR2000R-2, 2/3, 3
2.5/5.5 DC plug from power adaptor
D sub 9 P Female
to COM port
LOCATIONS OF SELECTORS
on PCB inside case
S6
S3
S1S5
S S2 4
J3
T2
T1
T3
J2
J1
P1
P2
U3
U4
U2
U1
CN2
JP3
2
JP4
JP1
CN2
U1
U3
CN1
T1
T2
T3
J1
J2
J3
JP2
2


Produktspezifikationen

Marke: Posiflex
Kategorie: Nicht kategorisiert
Modell: MR-2000U

Brauchst du Hilfe?

Wenn Sie Hilfe mit Posiflex MR-2000U benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Nicht kategorisiert Posiflex

Bedienungsanleitung Nicht kategorisiert

Neueste Bedienungsanleitung für -Kategorien-