Philips GC2560 Bedienungsanleitung
Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Philips GC2560 (9 Seiten) in der Kategorie Eisen. Dieser Bedienungsanleitung war für 4 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet
Seite 1/9
GC2652, GC2650, GC2640, GC2620,
GC2560, GC2530, GC2528, GC2522,
GC2520, GC2510
L J
A D F GECB
I
H
K
1
2 3 4 5
6 7 8 9
10 11 12 13
14 15 16 17
ENGLISH
Introduction
Congratulations on your purchase and welcome to
Philips! To fully benet from the support that Philips offers,
register your product at www.philips.com/welcome.
General description (Fig. 1)
A Spray nozzle
B Cap of lling opening
C Steam control
O = no steam
l = minimum steam
; = maximum steam
1 = Calc-Clean function
D Shot-of-steam button (all types except GC2510) 9
E Spray button T
F Automatic shut-off light (GC2560 only)
G Mains cord
H Anti-Calc tablet (all types except GC2522/GC2510)
I Temperature light
J Type plate
K Water tank
L Temperature dial
Important
Read this user manual carefully before you use the
appliance and save it for future reference.
Danger
Never immerse the iron in water.
Warning
Check if the voltage indicated on the appliance
corresponds to the local mains voltage before you
connect the appliance.
Do not use the appliance if the plug, the mains cord
or the appliance itself shows visible damage, or if the
appliance has been dropped or leaks.
If the mains cord is damaged, you must have it
replaced by Philips, a service centre authorised by
Philips or similarly qualied persons in order to avoid
a hazard.
Never leave the appliance unattended when it is
connected to the mains.
This appliance is not intended for use by persons
(including children) with reduced physical, sensory
or mental capabilities, or lack of experience and
knowledge, unless they have been given supervision
or instruction concerning use of the appliance by a
person responsible for their safety.
Children should be supervised to ensure that they
do not play with the appliance.
Do not let the mains cord come into contact with
the hot soleplate of the iron.
Caution
Only connect the appliance to an earthed wall
socket.
Check the mains cord regularly for possible damage.
The soleplate of the iron can become extremely hot
and may cause burns if touched.
When you have nished ironing, when you clean the
appliance, when you ll or empty the water tank and
also when you leave the iron even for a short while:
set the steam control to position O, put the iron on
its heel and remove the mains plug from the wall
socket.
Always place and use the iron on a stable, level and
horizontal surface.
Do not put perfume, vinegar, starch, descaling agents,
ironing aids or other chemicals in the water tank.
This appliance is intended for household use only.
Electromagnetic elds (EMF)
This Philips appliance complies with all standards
regarding electromagnetic elds (EMF). If handled
properly and according to the instructions in this user
manual, the appliance is safe to use based on scientic
evidence available today.
Before first use
1 Remove any sticker or protective foil from the
soleplate.
2 Let the iron heat up to maximum temperature and
pass the iron over a piece of damp cloth for several
minutes to remove any residues from the soleplate.
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
Preparing for use
Filling the water tank
Do not put perfume, vinegar, starch, descaling agents,
ironing aids, chemically descaled water or other
chemicals in the water tank.
1 Switch off the appliance and unplug it.
2 Set the steam control to position O (= no
steam) (Fig. 2).
3 Openthecapofthellingopening.
4 Tilttheironandllthewatertankuptomaximum
level under the tap (Fig. 3).
Note: Do not ll the water tank beyond the MAX indication.
Note: If the tap water in your area is very hard, we advise
you to use distilled water. Do not use chemically descaled
water.
5 Closethecapofthellingopening(‘click’).
Setting the temperature
1 Put the iron on its heel (Fig. 4).
2 To set the required ironing temperature, turn the
temperature dial to the appropriate position.
Check the laundry care label for the required ironing
temperature.
1 Synthetic fabrics (e.g. acrylic, viscose, polyamide,
polyester)
1 Silk
2 Wool
3 Cotton, linen
If you do not know what kind or kinds of fabric an article
is made of, determine the right ironing temperature by
ironing a part that is not visible when you wear or use
the article.
Silk, woollen and synthetic materials: iron the reverse side
of the fabric to prevent shiny patches. Avoid using the
spray function to prevent stains. Start ironing the articles
that require the lowest ironing temperature, such as those
made of synthetic bres.
3 Put the mains plug in an earthed wall socket.
The temperature light goes on.
4 When the temperature light goes out, wait a while
before you start ironing.
During ironing, the temperature light goes on from
time to time. This indicates that the iron is heating
up to the set temperature.
Using the appliance
Note: The iron may give off some smoke when you use it for
the rst time. This stops after a short while.
Steam ironing
1 Make sure that there is enough water in the water
tank.
2 Set the recommended ironing temperature (see
chapter‘Preparingforuse’,section‘Settingthe
temperature’).
3 Set the appropriate steam setting. Make sure
that the steam setting is suitable for the ironing
temperature selected: (Fig. 2)
ç for minimum steam (temperature settings 2 and
3).
é for maximum steam (temperature settings 3
to MAX).
Note: The iron starts to produce steam as soon as it has
reached the set temperature.
GC2640/GC2620/GC2530/GC2528/
GC2520/GC2510 only:
Water may leak from the soleplate if the set temperature
is too low (MIN to ). 2
Ironing without steam
1 Set the steam control to position (= no steam). O
2 Set the recommended ironing temperature (see
chapter‘Preparingforuse’,section‘Settingthe
temperature’).
-
-
-
-
,
,
-
-
Features
Spray function
You can use the spray function at any temperature
to moisten the article to be ironed. This helps
remove stubborn creases.
1 Make sure that there is enough water in the water
tank.
2 Press the spray button several times to moisten the
article to be ironed (Fig. 5).
Shot of steam (all types except GC2510)
A powerful shot of steam helps to remove very stubborn
creases.
The shot-of-steam function only works at temperature
settings between and MAX. 2
1 Press and release the shot-of-steam button (Fig. 6).
Vertical shot of steam (all types except
GC2510)
You can also use the shot-of-steam function when
you hold the iron in vertical position. This is useful for
removing creases from hanging clothes, curtains etc.
1 Hold the iron in vertical position and press and
release the shot-of-steam button (Fig. 7).
Never direct the steam at people.
Drip stop (GC2652/GC2650/GC2560/
GC2522 only)
This iron is equipped with a drip-stop function: the
iron automatically stops producing steam when the
temperature is too low to prevent water from dripping
out of the soleplate. When this happens you hear a click.
Automatic shut-off function (GC2560 only)
The automatic shut-off function automatically switches off
the iron if it has not been moved for a while.
Theautomaticshut-offlightashestoindicatethat
the iron has been switched off by the automatic
shut-off function. (Fig. 8)
To let the iron heat up again:
1 Pick up the iron or move it slightly.
The automatic shut-off light goes out.
If the temperature of the soleplate has dropped
below the set ironing temperature, the temperature
light goes on.
2 If the temperature light goes on after you have
moved the iron, wait for it to go out before you
start ironing.
Note: If the temperature light does not go on after you move
the iron, the soleplate still has the right temperature and the
iron is ready for use.
Cleaning and maintenance
Cleaning
1 Set the steam control to position , remove the O
plug from the wall socket and let the iron cool
down.
2 Wipeakesandanyotherdepositsoffthe
soleplate with a damp cloth and a non-abrasive
(liquid) cleaning agent.
To keep the soleplate smooth, avoid hard contact with
metal objects. Never use a scouring pad, vinegar or
other chemicals to clean the soleplate.
3 Clean the upper part of the iron with a damp cloth.
4 Regularly rinse the water tank with water. Empty
the water tank after you have rinsed it (Fig. 9).
Double-Active Calc System (all types except
GC2522/GC2510)
The Double-Active Calc System consists of an Anti-Calc
tablet inside the water tank combined with the Calc-
Clean function.
The Anti-Calc tablet prevents scale from clogging the
steam vents. The tablet is constantly active and does
not need to be replaced (Fig. 10).
The Calc-Clean function removes scale particles
from the iron.
,
,
,
-
-
4239.000.6137.4
Calc-Clean function
Use the Calc-Clean function once every two weeks. If
the water in your area is very hard (i.e. when akes come
out of the soleplate during ironing), use the Calc-Clean
function more frequently.
1 Make sure the appliance is unplugged.
2 Set the steam control to position . O
3 Fill the water tank to the maximum level.
Do not pour vinegar or other descaling agents into the
water tank.
4 Set the temperature dial to MAX (Fig. 11).
5 Put the mains plug in an earthed wall socket.
6 Unplug the iron when the temperature light goes
out.
7 Hold the iron over the sink and set the steam
control to the Calc-Clean position ( ). The steam 1
control springs up slightly.
8 Pull the steam control upwards and remove
it (Fig. 12).
9 Hold the iron over the sink and move it to and
fro (Fig. 13).
Steam and boiling water come out of the soleplate.
Impuritiesandakes(ifany)areushedout.
10 Use vinegar to remove scale, if any, from the steam
control needle (Fig. 14).
Do not bend or damage the steam control needle.
11 Put the steam control back into the iron. Insert
the point of the needle exactly in the centre of the
holeandtthesmallprojectiononthesideofthe
needle into the slot. Press down the steam control
while you turn it to position O (Fig. 15).
12 Repeat the Calc-Clean process if the iron still
contains a lot of impurities.
After the Calc-Clean process
1 Put the plug back into the wall socket and let the
iron heat up to let the soleplate dry.
2 Unplug the iron when the temperature light goes
out.
3 Move the iron gently over a piece of used cloth to
remove any water stains that may have formed on
the soleplate.
Storage
1 Set the steam control to position , remove the O
plug from the wall socket and let the iron cool
down.
2 Wind the mains cord round the cord storage
facility (Fig. 16).
3 Store the iron on its heel in a safe and dry place.
Environment
Do not throw away the appliance with the normal
household waste at the end of its life, but hand it in
at an ofcial collection point for recycling. By doing
this, you help to preserve the environment (Fig. 17).
Guarantee & service
If you need service or information or if you have a
problem, please visit the Philips website at www.philips.
com or contact the Philips Consumer Care Centre
in your country (you nd its phone number in the
worldwide guarantee leaet). If there is no Consumer
Care Centre in your country, go to your local Philips
dealer.
Troubleshooting
This chapter summarises the most common problems
you could encounter with the appliance. If you are unable
to solve the problem with the information below, contact
the Consumer Care Centre in your country.
Problem Cause Solution
The iron is
plugged in, but
the soleplate
is cold.
There is a
connection
problem.
Check the mains
cord, the plug and the
wall socket.
,
-
Problem Cause Solution
The
temperature
dial is set to
MIN.
Set the temperature
dial to the required
position.
The iron does
not produce
any steam.
There is not
enough water
in the water
tank.
Fill the water
tank (see chapter
‘Preparing for use’,
section ‘Filling the
water tank’).
The steam
control is set
to position
O.
Set the steam
position to or ç é
(see chapter ‘Using
the appliance’, section
‘Steam ironing’).
The soleplate
is not hot
enough and/
or the drip-
stop function
has been
activated
(GC2652/
GC2650/
GC2560/
GC2522
only).
Set an ironing
temperature that is
suitable for steam
ironing ( to 2
MAX). Put the iron
on its heel and wait
until the temperature
light goes out before
you start ironing.
The shot-
of- steam
function does
not work (all
types except
GC2510).
You have
used the
shot-of-steam
function too
often within
a very short
period.
Continue ironing in
horizontal position
and wait a while
before you use the
shot-of-steam
function again.
The iron
is not hot
enough.
Set an ironing
temperature that is
suitable for steam
ironing ( to 2
MAX). Put the iron
on its heel and wait
until the temperature
light goes out before
you start ironing.
Flakes and
impurities
come out of
the soleplate
during ironing.
Hard water
forms akes
inside the
soleplate.
Use the Calc-Clean
function one or
more times (see
chapter ‘Cleaning and
maintenance’, section
‘Calc-Clean function’).
The light on
the handle
ashes
(GC2560
only).
The
automatic
shut-off
function
has been
activated
(see chapter
‘Features’,
section
‘Automatic
shut-off’).
Pick the iron up
or move it slightly
to deactivate the
automatic shut-
off function. The
automatic shut-off
light goes out.
There
are water
droplets on
the fabric.
You have not
closed the
cap of the
lling opening
properly.
Press the cap until
you hear a click.
There
are water
droplets on
the fabric
(GC2640/
C2620/
GC2530/
GC2528/
GC2520/
GC2510
only).
The set
temperature
is too low for
steam ironing.
Set an ironing
temperature that is
suitable for steam
ironing ( to 2
MAX). Put the iron
on its heel and wait
until the temperature
light goes out before
you start ironing.
Problem Cause Solution
Water drips
from the
soleplate
after the iron
has cooled
down or has
been stored
(GC2640/
C2620/
GC2530/
GC2528/
GC2520/
GC2510
only).
You have put
the iron in
horizontal
position while
there was still
water in the
water tank.
Empty the water tank
and set the steam
control to position O
after use. Store the
iron on its heel.
4239.000.6137.4
Produktspezifikationen
| Marke: | Philips |
| Kategorie: | Eisen |
| Modell: | GC2560 |
Brauchst du Hilfe?
Wenn Sie Hilfe mit Philips GC2560 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten
Bedienungsanleitung Eisen Philips
9 Oktober 2024
2 Oktober 2024
29 September 2024
23 September 2024
15 September 2024
11 September 2024
7 September 2024
6 September 2024
6 September 2024
6 September 2024
Bedienungsanleitung Eisen
- Eisen Sinbo
- Eisen AFK
- Eisen Clatronic
- Eisen Domo
- Eisen Emerio
- Eisen G3 Ferrari
- Eisen Coline
- Eisen Tristar
- Eisen Sanyo
- Eisen Nedis
- Eisen SilverCrest
- Eisen Sunbeam
- Eisen Panasonic
- Eisen Clas Ohlson
- Eisen Quigg
- Eisen Adler
- Eisen Beper
- Eisen Bestron
- Eisen Camry
- Eisen Princess
- Eisen Trisa
- Eisen Bosch
- Eisen AEG
- Eisen Aigostar
- Eisen Ambiano
- Eisen Siemens
- Eisen Concept
- Eisen Electrolux
- Eisen Fagor
- Eisen Gorenje
- Eisen Jata
- Eisen Klarstein
- Eisen Lervia
- Eisen Miele
- Eisen Severin
- Eisen Unold
- Eisen Bomann
- Eisen Essentiel B
- Eisen H.Koenig
- Eisen Korona
- Eisen Melissa
- Eisen OK
- Eisen Russell Hobbs
- Eisen Taurus
- Eisen Tefal
- Eisen Vox
- Eisen Day
- Eisen ECG
- Eisen König
- Eisen Mesko
- Eisen Telefunken
- Eisen Black And Decker
- Eisen Arzum
- Eisen BEKO
- Eisen Blaupunkt
- Eisen Brabantia
- Eisen Braun
- Eisen Eldom
- Eisen Eta
- Eisen Grundig
- Eisen Heinner
- Eisen Hotpoint
- Eisen Inventum
- Eisen Krups
- Eisen Moulinex
- Eisen Primo
- Eisen Solac
- Eisen Tomado
- Eisen Wilfa
- Eisen AEG-Electrolux
- Eisen Alpina
- Eisen Exquisit
- Eisen Haier
- Eisen Hoover
- Eisen Privileg
- Eisen Frigidaire
- Eisen Svan
- Eisen King
- Eisen Philco
- Eisen Hitachi
- Eisen Hyundai
- Eisen Orava
- Eisen Orion
- Eisen Tesla
- Eisen Livoo
- Eisen Polti
- Eisen Easy Home
- Eisen Elica
- Eisen ProfiCare
- Eisen Elta
- Eisen Beem
- Eisen Jura
- Eisen Kooper
- Eisen Lümme
- Eisen Morphy Richards
- Eisen Rowenta
- Eisen Sencor
- Eisen DeLonghi
- Eisen Turmix
- Eisen Singer
- Eisen Maxwell
- Eisen Ariete
- Eisen Kalorik
- Eisen Optimum
- Eisen Rotel
- Eisen Scarlett
- Eisen Ufesa
- Eisen Calor
- Eisen Cecotec
- Eisen Zephir
- Eisen Punktal
- Eisen Termozeta
- Eisen LELIT
- Eisen Laurastar
- Eisen Matsui
- Eisen Cleanmaxx
- Eisen Domena
- Eisen Shark
- Eisen Maxxmee
- Eisen Nova
- Eisen Elba
- Eisen MPM
- Eisen Thomas
- Eisen Imetec
- Eisen Logik
- Eisen Team
- Eisen Andis
- Eisen JML
- Eisen Watshome
- Eisen Proline
- Eisen Westinghouse
- Eisen Lagrange
- Eisen Maxim
- Eisen Johnson
- Eisen Waves
- Eisen Vivax
- Eisen OBH Nordica
- Eisen Profilo
- Eisen Zelmer
- Eisen Breville
- Eisen Innoliving
- Eisen Jocca
- Eisen Vitek
- Eisen Mellerware
- Eisen Proctor Silex
- Eisen Ursus Trotter
- Eisen Swan
- Eisen Drew & Cole
- Eisen Hamilton Beach
- Eisen Orbegozo
- Eisen Izzy
- Eisen Saturn
- Eisen Defy
- Eisen Duronic
- Eisen Elgento
- Eisen Farberware
- Eisen Jocel
- Eisen Kambrook
- Eisen Oster
- Eisen Steamfast
- Eisen Sunny
- Eisen Grunkel
- Eisen Tower
- Eisen Vanguard
- Eisen Vaporella
- Eisen Kunft
- Eisen Becken
- Eisen Nevir
- Eisen Girmi
- Eisen Conair
- Eisen Lenoxx
- Eisen Flama
- Eisen Malmbergs
- Eisen Di4
- Eisen Khind
- Eisen Koblenz
- Eisen LERAN
- Eisen Currys Essentials
- Eisen Gallet
- Eisen Lafe
- Eisen Inno-Hit
- Eisen DPM
- Eisen Robinhood
- Eisen Create
- Eisen Brentwood
- Eisen BEP
- Eisen Britania
- Eisen CHI
- Eisen Michelini
- Eisen Imarflex
Neueste Bedienungsanleitung für -Kategorien-
16 Oktober 2024
16 Oktober 2024
16 Oktober 2024
16 Oktober 2024
16 Oktober 2024
14 Oktober 2024
13 Oktober 2024
13 Oktober 2024
12 Oktober 2024
12 Oktober 2024