Pearl Sports H-2050 Bedienungsanleitung


Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Pearl Sports H-2050 (8 Seiten) in der Kategorie Nicht kategorisiert. Dieser Bedienungsanleitung war für 19 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/8
Convertible
Spiked / Rubber Tipped Feet
VariSet
Footboard Angle
Adjustment
Interchangeable
Cam
Pedal Frame
Hi-Hat Clutch
Rubber Cymbal Seat
Hi-Hat Cup
Spring Tension Adjustment Dial
Die-Cast Joint
StopLock
Wing Bolt
Toe Stopper
TractionPlate w/Traction Grips
Support Casting
Base
Upper Tube
Upper Pull Rod
Congratulations on your purchase!
To get optimum performance of your H-2050 Hi-Hat Stand,
please read this Instruction Manual before playing.
H-2050
PEARL HI-HAT STAND
Instruction Manual
Key Bolt (for PowerShifter)
90°
2-B
2-C
2-A
CAUTION
Do not use the stand tilted. It would loose stability and would cause
the stand to fall over.
CAUTION
Depending on the position of the legs, the stand could become
unstable and fall over. Make sure that the stand itself is stable
before performance.
Fig.2-A, 2-B, 2-C
Strut End Clamp
Key Bolt
Key Bolt
Base Assembly
Hold the Pedal Frame with one hand. Loosen the Key Bolt
on the Support Casting and disengage the Tab (Fig.1-A).
Remove the Pedal Frame from the Docking Station as
shown (Fig.1-B), and tighten the Key Bolt to prevent noise
while performance.
Loosen the Key Bolts on both sides of the bottom of the
Support Casting, and open up the Clamp (Fig.2-A). Insert
the Strut Ends at the end of the Pedal Frame into the
Clamps at the angle shown (Fig.2-B). Make sure that the
Strut Ends are inserted all way in, and then rotate the Pedal
Frame downward as shown (Fig.2-C).Tighten the Key Bolts
on the Clamps to secure the Strut Ends.
Set the Base Section vertically.
Heel of the Footboard
Fig. 3
Fig. 4
Stand the base up and
holding it with one hand,
loosen the Wing Bolt and
open the legs. Make
sure that the legs are
forming a stable tripod,
and tighten the Wing Bolt
to retain setting (Fig.3).
Make sure both the Support Casting and the Heel part of
the Footboard are touching the playing surface, and that
the stand is set vertically (Fig. 4).
Wing Bolt
Fig. 5
The legs can be swiveled to
fit your setting. Loosen the
Wing Bolt and the Key Bolt
as shown in (Fig.5). Swivel
the legs to the desired
position and tighten the
Wing Bolt and Key Bolt to
retain the setting.
Wing Bolt
Key Bolt
Fig.1-A, 1-B
Docking Station
Support Casting
Key Bolt
Tab
Pedal Frame
1-B
1-A
A
BC
A : Strong feel
B : Normal feel
C : Light feel
Pull Cam
Key Bolt
Cam Wheel
Key Bolt Drive
Connector
Key Bolt
Heel Plate
VariSet Footboard Angle Adjustment
The Footboard angle can be adjusted in two ways. By
loosening the Key Bolt on the Pull Cam, you can change the
Footboard angle infinitely (Fig.8). You can also change the
angle by loosening the Key Bolt on the Cam Wheel, and
sliding the Drive Connector to one of the three positions
(Fig.9). Make sure to tighten the Key Bolts after
adjustments.
PowerShifter Adjustment
The PowerShifter function allows the feel of the pedal to be
changed from Strong, Normal, and Light.
To change the feel, loosen the Key Bolt on the Heel Plate
and move the Footboard to the A, B, or C position. Tighten
the Key Bolt to secure the Footboard (Fig.10).
Spring Tension Adjustment
The spring tension can be adjusted
quickly and precisely by turning the
Spring Tension Dial. This innovative
system features extended tension
range and click-stops for slip-proof
performance under the most
demanding playing conditions
(Fig.11).
Hi-Hat Cup Tilt Adjustment
Turn the Knurled Knob to tilt the
bottom cymbal to help prevent "air
lock" between the cymbals (Fig.7).
Fig.7
Fig.9
Fig.10
Fig.11
Fig.8
Knurled Knob
StrongLight
Fig.6-B
Fig.6-C
Fig.6-A
Top Hi-Hat
Cymbal
Bottom Nut
Rubber
Washers
Upper Tube
Upper Pull Rod
Stop Lock
Top Hi-Hat Cymbal
Lower Hi-Hat Cymbal
Hi-Hat Clutch
Die-Cast Joint
Wing Nut
Hi-Hat Cup
Bottom Nut
Connector
Upper
Pull Rod
Upper Section Assembly
Thread the Upper Pull Rod into the Connector inside the
Die Cast Joint as shown in (Fig.6-A) and tighten securely.
Insert the Upper Tube into the Die Cast Joint and set the
height to your preference then tighten the Wing Nut. Set the
Stop Lock by loosening the Key Bolt and sliding the Stop
Lock against the Die Cast Joint, then retighten the Key Bolt.
Thread the Lower Hi-Hat Cymbal through the Upper Pull
Rod and place it on the Hi-Hat Cup. Assemble the Top
Hi-Hat Cymbal and the Hi-Hat Clutch as shown in (Fig.6-B).
Tighten the Key Bolt on the Bottom Nut (Fig.6-C) to prevent
it from loosening during performance. Mount the Clutch
with the Top Hi-Hat Cymbal attached to the Upper Pull Rod.
Adjust the distance between the top and bottom cymbals to
your preference then secure the Clutch by tightening the
Wing Nut.
Tip
If the Footboard angle is set too high or too low, the action of the
Release Button (for the Interchangeable Cam system) can be
impaired. Should this happen, slightly readjust the angle of the Pull
Cam until the Release Button moves freely.
Wing Nut


Produktspezifikationen

Marke: Pearl Sports
Kategorie: Nicht kategorisiert
Modell: H-2050

Brauchst du Hilfe?

Wenn Sie Hilfe mit Pearl Sports H-2050 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Nicht kategorisiert Pearl Sports

Bedienungsanleitung Nicht kategorisiert

Neueste Bedienungsanleitung für -Kategorien-