Pearl Sports Decade Maple 6pc Bedienungsanleitung


Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung fĂŒr Pearl Sports Decade Maple 6pc (5 Seiten) in der Kategorie Nicht kategorisiert. Dieser Bedienungsanleitung war fĂŒr 22 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/5
Tom Holder
Crash Cymbal
Cymbal Boom Stand
Hi-Hat Stand
Snare Stand
Drum Throne
Drum Pedal
Cymbal Stand
Ride Cymbal
Hi-Hat Cymbal
Snare Drum
Tom Tom Tom Tom
Bass Drum
Floor Tom
Instruction Manual
Congratulations on your purchase! To get optimum performance from your Pearl drum set,
please read this Instruction Manual first before playing.
PEARL DRUMS
Set-Up Example
*Illustrations shown in this manual are Decade Maple drums and 930 series hardware.
* Cymbals are not included in the set.
E X L・E X X
4. Position the Bass Drum with the Tom Holder Bracket
facing upwards. Loosen the Wing Nut on the Bass
Drum Spur and rotate it to the position shown. Tighten
the Wing Nut to secure. Loosen the Wing Bolt and
extend the Spurs so that the front of the Bass Drum is
about an inch off the floor. Make sure that the Spurs on
both sides are equal in length, and tighten the Wing
Bolts. The Bass Drum Spurs have Spike Tips (for added
slip resistance) that can be exposed by turning the
Lock Nut and Rubber Tip clockwise (Fig.5).
1. Place the Shell on a clean, solid surface with the front
side (the side with the Bass Drum Spurs attached)
facing upwards. Put the Front Head with Pearl Logo on
the Shell then attach the Bass Drum Hoop with flat side
down on the Rim of the Head (Fig.1).
3. Turn the Shell over to the batter side and place the
other Head and Bass Drum Hoop on the Shell. The
batter side Bass Drum Hoop has a Hoop Protector
(Fig.4) where the Pedal is to be attached. Position the
Bass Drum Hoop so that the Hoop Protector is on the
opposite side of the Tom Holder Bracket. Attach the
Tension Rods/Hooks in the same way as the front side
(Fig.3).
Bass Drum Assembly
The Bass Drum is packed with the Shell, Bass Drum
Hoops, Heads and Parts unassembled. Please follow the
instructions below to assemble the Bass Drum.
Fig.2
Fig.5
2. Pass a Tension Rod through a Hook, and hook it on the
Bass Drum Hoop above a Lug. Finger tighten the
Tension Rod into the Lug and do the same with the rest
of the Tension Rods/Hooks on this side of the drum
(Fig.2). Using a Tuning Key, tighten the Tension Rod
until secure (Refer to the “Basic Tuning” section at the
end of this manual).
CAUTION
The Spike Tips are sharp. Be careful not to hurt yourself or
others when using them. Use the Spike Tips only on thick
carpeted surfaces to prevent damage to the flooring underneath.
Note
The Bass Drum Hoop without the Hoop Protector (Fig.4) is
used on the front side.
Fig.4
Tom Holder Bracket
Hoop Protector
Hoop Protecter
Hook
Tension Rod
Bass Drum Hoop
Head
Bass Drum Hoop
Cross-section
drawing
Bass Drum Spur
Bass Drum Hoop
Front Head (w/Logo)
Shell
Fig.1
(Front side)
Fig.3
(Batter side)
Tension Rod
Hook
Lug
Bass Drum Hoop
Rim of the Head
Spike Tip
Lock Nut
Rubber Tip
Wing Bolt
Wing Nut
Bass Drum Spur
Tom Holder Bracket
Tom Tom Setting
Insert the long ends of the Tom Holders into the Tom
Holder Bracket on the Bass Drum as shown (Fig.8) and
tighten the Wing Nuts on the Tom Holder Bracket. Next,
loosen the Key Bolts on the TH-900I Tom Holders using a
Tuning Key or loosen the Wing Nuts on the TH-70 I Tom
Holders. Adjust the angle of the Tom Holders so you can
attach the Tom Toms easily then retighten the Key
Bolts/Wing Nuts (Fig.9). Attach the Tom Toms to the other
end of the Tom Holders and tighten the Wing Nuts on the
mounts on the Tom Toms.
Floor Tom Assembly
The Floor Tom is packed with the Shell, Steel Hoops,
Heads and Floor Tom Legs unassembled. Please follow
the assembly instructions below to assemble the Floor
Tom.
2. Line up the ears of the Steel Hoop over the Lugs and
insert the Tension Rods through the ears. Finger tighten
them into all the Lugs on this side of the drum. Using a
Tuning Key, tighten the Tension Rods until secure (Refer
to the “Basic Tuning” section at the end of this manual)
(Fig. 6).
3. Turn the drum over and attach the other Head and Steel
Hoop with the remaining Tension Rods.
4. Attach the Floor Tom Legs to the Floor Tom Leg
Brackets and set the height and angle to your
preference. Tighten the Wing Bolt to secure position
(Fig.6 , 7).
1. Place the Shell on a clean, solid surface with the batter
side facing upwards as shown in Fig.6. Put the Head on
the Shell followed by the Steel Hoop.
Tension Rod
Steel Hoop
Head
Lug
Floor Tom Leg
Wing Bolt
Floor Tom Leg
Bracket
Fig.7
Fig.6
Fig.8
Fig.9
TH-900 I
Tom Holder
TH-70 I
Tom Holder
Key Bolt Wing Nut
Note
The Tom Holders are equipped with StopLocks that keep the
drums from slipping or rotating and to memorize position
settings for quick and repeatable set-ups. When the position
of the Tom Toms are set, place each StopLock into the slots
in the Tom Holder Bracket and the mounts on the Tom Toms
to retain these settings (refer to the Set-Up Example
illustration on the first page of this manual).
Note
For Decade Maple, use the Thicker Head for the batter side.
The EXPORT Floor Toms are packed with the Heads and
Hoops assembled. Please proceed to step 4.
StopLock
Key Bolt
Tom Holder Bracket


Produktspezifikationen

Marke: Pearl Sports
Kategorie: Nicht kategorisiert
Modell: Decade Maple 6pc

Brauchst du Hilfe?

Wenn Sie Hilfe mit Pearl Sports Decade Maple 6pc benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Nicht kategorisiert Pearl Sports

Bedienungsanleitung Nicht kategorisiert

Neueste Bedienungsanleitung fĂŒr -Kategorien-