PAC SWI-JACK Bedienungsanleitung


Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für PAC SWI-JACK (8 Seiten) in der Kategorie Nicht kategorisiert. Dieser Bedienungsanleitung war für 13 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/8
1
06-08-09
SWI-JACK
Universal Steering Wheel Control Interface
Before You Start
A. Is this product compatible with the vehicle?
• See application guide (separate sheet) for listing of vehicles and connection information. If not, please visit
http://www.pac-audio.com/swixprogramming/swixprogramming.asp for the most current list of compatible
vehicles.
B. Prepare for the installation.
• If possible, install the SWI-JACK while you are installing the new head unit. Keep in mind you may need to plug in
the factory stereo to locate certain wires; therefore do not complete the head unit installation until the SWI-JACK is
working properly.
• Plan a general installation location for both the SWI-JACK plug and the control body. Keep in mind that the sup-
plied wire harness is , and the 1/8" plug harness is . two feet long three feet long
• Use a multimeter or approved measuring device for checking vehicle circuits.
Pacific Accessory Corporation
SEEK
PRESET AM F M
VOLUME
PLAY MU TE
Power
Jack for the SWI-JACK
Steering wheel
audio control wire
To Kenwood or
OEM wired
remote control input
Installation Instructions
For Alpine, JVC, Clarion, Kenwood,
Valor, OEM & Blaupunkt OEM
Steering Remote Ready Radios
For Alpine, Clarion JVC, or Valor radios, connect the SWI-JACK 1/8" plug into the radio's Steering Wheel input
jack on back of radio or wire harness. For Kenwood, or OEM radios, connect the blue/yel wire to the Remote Input wire
(blue/yel for Kenwood, gray for OEM) of radio.
Blaupunkt radios with optional wireless remote inputs are supported by the SWI-JACK, however we do not
supply any connectors or support for Blaupunkt. It is up to the consumer or installer to supply this connector. Use
vehicle Connector Chart and use VW connector as reference. Connect the SWI-JACK's blue/yel wire to pin #11 of VW
connector. The connector you obtain may come with two of three pieces, however the connector (usually green) should
show pin #11 on it.
2
SWI-JACK
Wiring Connections
Step 1.
Connect the BLACK
wire to ground (-).
Verication: Wire
or location registers
a constant (-) when
probed.
Step 2.
Connect the RED wire
to switched +12V.
Verication: Wire reg-
isters +12V when the
ignition key is turned
to the ACC or ON posi-
tions.
Step 3.
Connect the appropriate interface wire (WHITE, YELLOW, ORANGE or
GREEN).
• Refer to the . Locate the vehicle and Identication and Connection Chart
note the SWC wire color in the “Interface Wire Color” column.
• Note the vehicle wire color and location information in the “Identication”
column.
Note: You will only connect ONE of these wires. The other 3 wires will not
be used. Cut and insulate the unused wires.
• Connect the wire as indicated in the chart.
• If your vehicle is not listed on the , Identification and Connection Chart
Visit www.pac-audio.com/swixprogramming/swixprogramming.asp
Note: Only 3 wires from the SWI-JACK will be used during installation. GM vehicles programmed for version #4, will
use 4 wires.
Step 4a.
Connect the BLUE
serial data wire.
Connect this wire
ONLY on GM
passenger vehicles (no
trucks or SUVs) with
airbags AND steering
wheel heater controls.
For all other vehicles,
cut and insulate the
BLUE wire.
Step 4b.
If instructed by the
Vehicle Application
Guide, cut the
BROWN wire loop and
insulate both halves.
Step 4c.
If instructed by the
Vehicle Application
Guide, cut the VIOLET
wire loop and insulate
both halves, or place a
resistor in-line of wires.
Note: is for vehicles made by Step 4a
General Motors that are programmed
for version #4 only. If no connections is
necessary, proceed to Step 4b.
Step 4
If necessary, perform the following operations as indicated by the notes in .Identication and Connection Chart
SWI-JACK SWI-JACK
SWI-JACK
SWI-JACK
SWI-JACK
SWI-JACK
3
06-08-09
Step 5.
Refer to The Vehicle Application Guide INTERFACE Version Number. Note the next to the selected vehicle. Fill in the information
below for quick reference. The Radio Select Switch must be set BEFORE programming the INTERFACE version number. Set the
switch as follows: Alpine = 1, JVC = 2, Kenwood = 3, Clarion = 4 Valor = 5 OEM = 6 and Blaupunkt = 7
Version Number: ____________
SWI-JACK
SWI-JACK
Programming the SWI-JACK to Work With the Vehicle
Step 6.
Press and hold programming/
mode button on SWI-JACK. Turn
the vehicle ignition to the ON
position.
The LED on the
SWI-JACK will light.
Step 7.
Release the programming/
mode button.
The LED will turn off,
indicating memory is
cleared.
Step 9.
Press and release the program-
ming/mode button the same
number of times as the desired
version number.
The LED will ash
each time the button is
pressed and released.
After 3 seconds, the
LED will ash the same
amount of times of set
version number.
Step 10.
Turn vehicle ignition
to OFF position.
Vehicle programming
sequence is complete.
SWI-JACK
OFF
ACC
IGN
STRT
OFF
ACC
IGN
STRT
SWI-JACK
SWI-JACK
SWI-JACK
(Write Version Number here)


Produktspezifikationen

Marke: PAC
Kategorie: Nicht kategorisiert
Modell: SWI-JACK

Brauchst du Hilfe?

Wenn Sie Hilfe mit PAC SWI-JACK benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Nicht kategorisiert PAC

Bedienungsanleitung Nicht kategorisiert

Neueste Bedienungsanleitung für -Kategorien-