PAC CP1-FRD1 Bedienungsanleitung


Lesen Sie kostenlos die đź“– deutsche Bedienungsanleitung fĂĽr PAC CP1-FRD1 (3 Seiten) in der Kategorie Nicht kategorisiert. Dieser Bedienungsanleitung war fĂĽr 7 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/3
© 2023 AAMP Global. All rights reserved. PAC is a Power Brand of AAMP Global.
PAC-Audio.com
C
Page 1
Rev: V1
Date: 021323
CANPRO Harness
for Select Ford Vehicles
CP1- FRD1
Output 8 Pos. 250mA
Output 7 Pos. 250mA
Output 6 Pos. 250mA
Output 5 Pos. 250mA
Output 4 Pos. 250mA
Output 3 Speed Pulse
Output2 Pos. 250mA
Output1 Pos. 250mA
Output 9 Neg. 250mA
The CP1-FRD1 is a factory matched plug & play harness for use with the CANPRO CP1-S CAN-Bus Interface Module
for select Ford Model applications using the 8pin data harness for connection at the Steering Column Control Module
(SCCM). The harness and module allow a simple and safe way to access vehicle information, status and triggers from
the CAN-Bus for a wide range of aftermarket uses such as radar detectors, camera activation, sound system upgrades,
lighting and more!
Introduction and Features
Important Notes
1. Any unused outputs should be insulated to prevent shorting.
2. The outputs of the CANPRO are low current (250mA) and require the use of a separate relay if additional current is required.
3. The vehicle should be in a resting state prior to opening connection to the 8pin data harness. See Installation note for further
information.
Wiring Connection Chart
Outputs
To Factory
Harness
Description
Description
Description
Description
Description Polarity
Polarity
Polarity
Polarity
Polarity Wire Color
Wire Color
Wire Color
Wire Color
Wire Color
Output 1 Accessory + Positive (250mA) White-Red
Output 2 Illumination + Positive (250mA) Blue
Output 3 Speed Pulse Pulse Green-Black
Output 4 Reverse + Positive (250mA) Violet-Black
Output 5 Ignition* + Positive (250mA) Yellow-Black
Output 6 Left Turn Signal + Positive (250mA) Red-Black
Output 7 Right Turn Signal + Positive (250mA) Gray-Red
Output 8 High Beam + Positive (250mA) Blue-Black
Output 9 Parking Brake - Negative (250mA) Brown-Black
Output Wires
1-9
DIP Switches
16pin
Interface
Connector
Status
LED
CANPRO CP1-S
* In Electric Vehicles, Output 5 provides a positive output when the vehicle is in a “Ready to Drive” state.
To Vehicle's
SCCM
© 2023 AAMP Global. All rights reserved. PAC is a Power Brand of AAMP Global.
PAC-Audio.com
C
Page 2
Rev: V1
Date: 021323
CANPRO Harness
for Select Ford Vehicles
CP1- FRD1
Installation
1. Set the DIP switches on the CP1-S as shown in below.
2. To access the vehicle's CAN data harness, the steering
column shroud must be removed. Remove the two screws
(7mm or 9/32") from the underside of the shroud. (FIG A)*
3. Pull downward along the bottom edge of the shroud to
release the retaining clips and pull towards the rear of the
vehicle to remove the bottom portion of the shroud. (FIG B)*
4. CAN Ensure the vehicle is Powered O󰀨 and unplug the 8pin
data harness pictured. (FIG C)*
5. Connect one end of the CP1-FRD1 harness to the matching
connector in the vehicle. Connect the remaining vehicle
connector from the CP1-FRD1 to the other end of the vehicle
harness and route the CP1-FRD1 harness along the OEM
harness toward the bottom of the dash.(FIG D)*
6. Determine a mounting location for the CANPro module in a
place where it does not interfere with the movement of any
vital vehicle equipment and secure the module.
7. Connect the 16pin CP1-FRD1 connector into the CANPro
and lengthen and route any Output wires needed. Insulate
any unused Output wires!
8. After wire connections and testing are complete, secure the
CP1-S module and reinstall the console panels.
*2021 Ford Mustang Mach-E used for photos. Other
CP1-FRD1 applications may vary slightly. For instance
the Lightning has a third screw holding the bottom
shroud in place that needs to be removed.
1 2 3 4 5 6 7 8
ON
FIG A
FIG B
NOTE! Verify the vehicle is off prior to disconnecting the 8pin vehicle harness
and do not turn on the accessory or ignition until the 8pin male and female
connectors from the CP1-FRD1 are connected.
FIG D
FIG C
© 2023 AAMP Global. All rights reserved. PAC is a Power Brand of AAMP Global.
PAC-Audio.com
C
Page 3
Rev: V1
Date: 021323
CANPRO Harness
for Select Ford Vehicles
CP1- FRD1
LED Status Information
ACTION/COLOR
ACTION/COLOR
ACTION/COLOR
ACTION/COLOR
ACTION/COLOR Description
Description
Description
Description
Description
Fast Flashing RED Update mode, for updating of the application or resource îšżles.
Slow Flashing (0.5sec) GREEN Normal Operation
Slow Flashing (0.5sec) GREEN,
plus additional 0.5sec RED
System Fault. The number of times the interface ashes RED indicates the chan-
nel (output) with a fault condition. For example, if the LED ashes GREEN, then
ashes RED twice, then back to Green, Channel 2 has a fault condition.
To check the fault, see Troubleshooting section below.
Troubleshooting
1. No LED activity: Disconnect and reconnect the CP1, does the LED ash? If not, check the 3 amp fuse in the fuse-holder that
is located 2 inches from the 16pin connector on the Yellow wire.
2. No Outputs: Verify the DIP switch setting is correct (Installation section, FIG A). If the DIP switch setting needs to be changed,
unplug the CP1, change the DIP setting and then reconnect. If the LED is ashing green, test the outputs using a multimeter.
If the multimeter is showing the proper output, add a relay to the output to increase current capability.
3. System Fault: Disconnect the faulty output (1-9), disconnect and reconnect the 16pin connector to the CP1 so that it loses
and gains back power and ground, does it stop ashing red? Check wiring to faulty output to make sure it is not shorted to
ground, or add a relay.
Technical Support
Email: support@PAC-audio.com
Phone: 727-592-5991
Chat: PAC-Audio.com


Produktspezifikationen

Marke: PAC
Kategorie: Nicht kategorisiert
Modell: CP1-FRD1

Brauchst du Hilfe?

Wenn Sie Hilfe mit PAC CP1-FRD1 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Nicht kategorisiert PAC

Bedienungsanleitung Nicht kategorisiert

Neueste Bedienungsanleitung fĂĽr -Kategorien-