PAC RPK4-HD1101 Bedienungsanleitung

PAC Nicht kategorisiert RPK4-HD1101

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für PAC RPK4-HD1101 (10 Seiten) in der Kategorie Nicht kategorisiert. Dieser Bedienungsanleitung war für 4 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/10
Complete Radio Replacement Kit with
Integrated Climate Control Retention for
2003-2007 Honda Accord
RPK4-HD1101
Page 1
© 2018 AAMP Global. All rights reserved. PAC is a Power Brand of AAMP Global.
PAC-audio.com
Rev: V8
Date: 081318
Parts List
This kit contains:
1. Dash Kit
a.1 (x1) HVAC Control Panel
b.1 (x2) Radio Mounting Brackets (One left and one right)
c.1 (x1) Pocket (For single DIN applications)
d.1 (x8) Radio Mounting Screws
2. Lower Pocket
3. Climate and Steering Wheel Control Interface Module
4. Adapter for Vehicles Equipped with the Factory Navigation Radio
5. HVAC Knob Inserts (Single Zone and Dual Zone)
6. Radio Connection Harnesses
7. 1 Sheet of HVAC Duct Sealing Material. (Used when the factory foam
has deteriorated between the ducts behind the radio.)
8. USBDMA3 - USB extension for use with the aftermarket radio
Overview
The RPK4-HD1101 is a complete radio replacement kit with integrated climate control retention for the 2003-2007 Honda Accord. This kit
utilizes a user friendly pair of HVAC control knobs for a factory look and experience. Using the supplied interchangeable inserts, this kit is
compatible with both single zone and dual zone HVAC systems. This kit is also programmable for use in both left hand drive and right hand
drive vehicles. The included radio replacement interface will retain factory steering wheel controls (SWC) and allows you to program two
radio functions to each SWC button by using short press long press dual command functionality. The interface also provides data bus driven
outputs such as vehicle speed sensor (VSS), reverse trigger and parking brake.
Table of Contents: Page:
1. Factory Radio Removal ----------------------------------------------------- 1-2
2. Sub-Dash Preparation Sealing the Air Ducts------------------------------ 3
3. Radio Replacement Installation and Wiring Instructions-------------- 3-4
4. Kit Assembly Instructions -------------------------------------------------- 5-6
5. Settings Menu (including SWC programming)------------------------- 7-10
1. This version of instructions are ONLY R.2.1.2.13 intended for use with product version or later.
2. The Pink / Black data input wire only needs to be connected in vehicles equipped with single zone climate controls. See page 6 to identify the
HVAC system in the vehicle.
3. The White / Black navigation SWC input wire only needs to be connected in vehicles equipped with the factory navigation radio, and when the
supporting “Voice” and “Back” steering wheel controls are present.
4. 7KH+9$&FRQWUROSDQHOZLOOQHHGWREHSURJUDPPHGWRWKHIDFWRU\+9$&V\VWHPLQWKHYHKLFOH8SRQSRZHULQJWKHSDQHOXSIRUWKH¿UVWWLPH
it will enter this programming mode. Please see page 6 for proper selection.
5. $SRFNHWKDVEHHQSURYLGHGWRUHSODFHWKHIDFWRU\SRFNHWEHORZWKHUDGLR7KHSRFNHWFRPHVZLWKDFXWRXWVL]HGVSHFL¿FDOO\IRUXVHZLWKWKH
included PAC USBDMA3.
Important Notes
1a.
4.
1d.
7. 1c.
3.
1b.
5.
6.
2.
The RPK4-HD1101 includes everything you need for a professional installation of an aftermarket radio in your Accord.
8.
***Please check all functions of the factory steering wheel controls and HVAC system and make sure it is all
in good working order before proceeding with this install.***
Complete Radio Replacement Kit with
Integrated Climate Control Retention for
2003-2007 Honda Accord
RPK4-HD1101
Page 2
© 2018 AAMP Global. All rights reserved. PAC is a Power Brand of AAMP Global.
PAC-audio.com
Rev: V8
Date: 081318
1.3 - If the vehicle is equipped with
manual transmission, the shift knob
( ) will need to be removed. To do A
this, lower the shift lever boot ( ) to B
release the hooks ( ) from the knob.C
Remove the shift knob by twisting it
counterclockwise.
1.4 - Using a plastic trim tool, detach
the clips ( , ) by pulling the center A B
console front panel ( ) up. If equipped, C
disconnect the seat heater switch
connectors ( ).D
1.5 - Using a plastic trim tool, pry up on
the right side of the console pocket ( )A
with a trim tool, and detach the clips,
then remove the pocket.
1.6 A - Remove the screws ( ), detach
the clips ( ) and hook ( ) by pulling the B C
center holder ( ) up, and disconnect D
the front accessory power socket
connector ( ).E
1.7 A - Remove the center pocket ( ).To
do this, remove the screws ( ).OpenB
the lid, then pull the pocket toward you
by hand to detach the clips ( ). Close C
the lid, then remove the pocket.
1.8 - Remove the 3 phillips head screws
and 2 8mm bolts holding the radio to
the dash. Pull the radio from the dash
and disconnect the connectors and the
antenna lead, then remove the radio
and set aside.
Part One: Removing the factory radio from the vehicle
1.1 - Push the hazard warning switch
button (A&DUHIXOO\LQVHUWDÀDWWLS
screwdriver into the slot below the button,
and push down on the center clip.
1.2 - A Pull the upper panel ( ) in the direction shown to
release the remaining clips, disconnect the hazard warning
switch connector ( ), and if equipped, sunlight sensor B
connector ( ) and navigation sub display connector ( ).C D
Detach the harness clips ( ), then remove the upper E
panel.
Complete Radio Replacement Kit with
Integrated Climate Control Retention for
2003-2007 Honda Accord
RPK4-HD1101
Page 3
© 2018 AAMP Global. All rights reserved. PAC is a Power Brand of AAMP Global.
PAC-audio.com
Rev: V8
Date: 081318
1. The radio select DIP switches on the front of the interface must be adjusted to the proper radio setting
before plugging the interface into the vehicle.
2. Make all connections between the aftermarket radio and the RPK4-HD1101 harness as described in the chart on the next page. This
includes the SWC 3.5mm jack or the SWC wire (aftermarket radio MUST support a wired remote input).
3. Connect the Pink / Black data wire when the vehicle is equipped with single zone HVAC controls, and data generated navigation outputs
are needed. See the next page for connection details.
4. Connect the White / Black navigation SWC wire when the vehicle is equipped with the factory navigation system, and when the supporting
“Voice” and “Back” steering wheel controls are present. See the next page for connection details.
5. Connect one side of the harness labeled “RPK-HD1101-16P” to the back of the kit. Connect the other end of the harness to the radio
replacement interface.
6. &RQQHFWWKHVLQJOH]RQH+9$&KDUQHVVRUGXDO]RQH+9$&KDUQHVVHVWRWKHUDGLRUHSODFHPHQWLQWHUIDFH)RUSURSHURSHUDWLRQFRQ¿UP
that the connectors are connected into the proper openings. Failure to verify will cause the HVAC kit to function incorrectly. Reference the
LOOXVWUDWLRQRQWKHQH[WSDJHRUWKHVWLFNHURQWKHEDFNRIWKHPRGXOHIRUFODUL¿FDWLRQ,IWKHYHKLFOHLVHTXLSSHGZLWKIDFWRU\QDYLJDWLRQWKHQ
connect the OEM upper display harness as well.
7. If you wish to reassign functions to the SWC follow the programming instructions on page 7.
3DUW7KUHH&RQ¿JXUDWLRQDQG:LULQJRI,QWHUIDFH
ON
1234
Other = Advent, BOYO, Dual, Lightning Audio, Rockford Fosgate, Visteon
Set DIP switches that match your radio to the ON position
Set all other DIP switches to the OFF position
Alpine JVC Kenwood Clarion Pioneer/Other Sony Fusion
1 2 1 & 2 3 1, 2, & 3 4 1 & 4
Part Two: Sub-Dash Preparation
1. Cut and remove the portion of the dash that is outlined below. Be sure to cut
close to the left and right square mounting holes but be sure they are left intact.
2. The Sub-dash should look like the image below when the removal is complete.
Notice that the left and right square mounting holes are still left intact.
Blocking the Air from the Air Ducts Behind the Radio
In vehicles equipped with dual zone climate controls, leaking air ducts will cause false readings to the temperature sensors in the
dash kit. This will cause the Auto climate feature to not heat or cool the cabin to the proper temperature. It is common for the ducts
behind the radio to leak due to deterioration of the seals between the main and center ducts. To help block the air from blowing on
the back of the temperature sensors we have added a piece of closed cell foam, measuring 6” x 12”.
7KHVXEGDVKRIWKHYHKLFOHZLOOQHHGWREHPRGL¿HGWR¿WWKHQHZDIWHUPDUNHWUDGLR3OHDVHVHHEHORZIRUSURSHUPRGL¿FDWLRQRI
the sub-dash. Be sure to leave the left and right lower clip mount intact as they will be re-used by the new dash kit.
UP
1. Connect the factory radio and turn the HVAC fan speed to high.
2. Verify if and where there is an air leak. The picture on the right shows the
common leak locations.
3. Using the closed cell foam provided as-is, or cut adequate pieces to block the
air from blowing on the back of the Temp sensors located just outside of the
radio opening on each side of the dash kit.
4. Verify that all of the air leaks have been sealed or redirected away from the
temperature sensors.
5. Disconnect the radio and proceed to the next step.


Produktspezifikationen

Marke: PAC
Kategorie: Nicht kategorisiert
Modell: RPK4-HD1101

Brauchst du Hilfe?

Wenn Sie Hilfe mit PAC RPK4-HD1101 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Nicht kategorisiert PAC

Bedienungsanleitung Nicht kategorisiert

Neueste Bedienungsanleitung für -Kategorien-