PAC RPA-KNOB1 Bedienungsanleitung


Lesen Sie kostenlos die đź“– deutsche Bedienungsanleitung fĂĽr PAC RPA-KNOB1 (2 Seiten) in der Kategorie Nicht kategorisiert. Dieser Bedienungsanleitung war fĂĽr 17 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/2
Climate control knob set for
2010 - 2015 Chevrolet Camaro
© 2018 AAMP Global. All rights reserved. PAC is a Power Brand of AAMP Global.
PAC-audio.com
C
Rev: 1
Date: 110918 Page 1
RPA-KNOB1
Introduction and Features
Very Important Notes
Pre-installation setup
RPA-KNOB1 is a complete set of two climate control knobs for 2010 - 2015 Chevrolet Camaro. They are designed to match
the OE climate control knob îšżt and îšżnish, providing a factory appearance in your late-model Camaro. They can be installed
on our PAC RadioPRO Integrated Dash Kit RPK5-GM4101, or as a replacement for the original knobs on a factory radio.
Both knobs feature back-lit buttons to match the OE appearance, and selectable center inserts to match the vehicle options,
for vehicles equipped with or not equipped with heated seats.
Note 1: The center inserts are made to install once! They are not easily removable / swappable.
Please ensure you have selected the correct inserts for your installation before snapping the inserts into the
control knobs.
In the event that the center inserts need to be removed, see the troubleshooting section on page 2.
Note 2: For vehicles with heated seats: When installing the center caps, you need to îšżrst install the light pipes. They are
keyed so they will only îšżt one way. Pay close attention to the shape and orientation of the light pipes to ensure
correct lighting.
Note 3: In this manual we will refer to “Left” indicating the driver side, and “Right” indicating the passenger side.
For vehicles without heated seats: Remove the center cap called “Blank Left” and snap that into the climate control knob
labeled Left. the insert is keyed, so it will only t in one orientation. Remove the center cap called “Blank Right” and snap it
into the climate control knob labeled Right.
For vehicles equipped with heated seats: Carefully open the package labeled “Heated Seat Left”. There will be a center
cap and 2 small, clear plastic, light pipes. They are keyed, so they will only îšżt in one speciîšżc hole each.
From the front of the control knob, insert the light pipes (non-keyed side îšżrst) into the small rectangular openings.
The left light pipe (A) has a key tab on the narrow side. Insert this light pipe with the key facing down.
The right light pipe (B) has the key tab on the wide side. Insert this light pipe with the key facing to the right.
They are installed as shown below.
(A)
(B)
Close-up of light pipes installed
key tab
key tab
Installation Steps for RPA-KNOB1 into an OE Radio
Installation on a factory radio: 1) Remove the OE knobs. 2) The original brackets and screws will be resused.
3) Install the RPA-KNOB1 knobs by reversing the steps used to remove the OE knobs.
Climate control knob set for
2010 - 2015 Chevrolet Camaro
© 2018 AAMP Global. All rights reserved. PAC is a Power Brand of AAMP Global.
PAC-audio.com
C
Rev: 1
Date: 110918 Page 2
RPA-KNOB1
Installation Steps for RPA-KNOB1 into an RPK5-GM4101
1) Secure the 2 support brackets to the PAC HVAC control assembly
mounted in the RPK5-GM4101 main kit plastic.
Be sure the alignment tabs are seated properly in the circuit board.
Carefully tighten 4 phillips screws into each bracket.
2) From the front side of the kit, secure the 2 support brackets to
the circuit board. The small screws will pass through the front of the
board where indicated, and will thread into the plastic brackets.
Be sure that the alignment tabs are seated properly.
3) Ensure the rubber membranes are in place behind each knob,
before installing them.
They are keyed, so they will only îšżt correctly one way. Note the
orientation in the image, with the swiper-contact at the top.
4) Position the knobs in the proper opening so that the buttons are
straight and insert them into the opening. With VERY LITTLE force,
rotate them slightly left and right while pusing them toward the circuit
board.
Once the alignment tabs are lined up, they should click and lock into place.
Use extra caution, as the contacts could bend while rotating.
5) From the back side of the kit, secure the knobs to the circuit board
using the screws where indicated (2 screws per knob).
Troubleshooting
To remove / swap the center inserts in the knob assemblies:
1) Access the back of the control knobs.
2) Carefully remove the 2 small phillips screws, securing the light-pipe into the control knob assembly.
3) Remove the lightpipe from the control knob assembly, and set aside.
4) Looking down into the center of the knob assembly, notice the two gray tabs, one on each side.
5) Using a very small at-blade screwdriver, carefully insert the screwdriver on the outside of the gray tabs, to disengage the latch.
6) Remove the center insert, and replace it with the correct insert for your vehicle (heated seats or blank).
1
2
3
4
5


Produktspezifikationen

Marke: PAC
Kategorie: Nicht kategorisiert
Modell: RPA-KNOB1

Brauchst du Hilfe?

Wenn Sie Hilfe mit PAC RPA-KNOB1 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Nicht kategorisiert PAC

Bedienungsanleitung Nicht kategorisiert

Neueste Bedienungsanleitung fĂĽr -Kategorien-