PAC RP4-NI11 Bedienungsanleitung


Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für PAC RP4-NI11 (9 Seiten) in der Kategorie Nicht kategorisiert. Dieser Bedienungsanleitung war für 4 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/9
RP4-NI11
Finding an Accesory 12v+
in 2014+ Nissan Rogue With a Navigation radio
Paciîš¿c Accessory Corporation
® | Santa Ana, California 92705 | Ph. 866-931-8021 | support@pac-audio.com
©2013 Pacic Accessory Corporation
www.pac-audio.com
Rev. 011116
C
Page 1
Tech Bulletin
Important Notes
Illustration / Schematic
When installing the RP4-NI11 into a 2014+ Nissan Rogue it may be necessary to make a hardwired connection for accessory
power. This is necessary due to these vehicles having a different location for the 12v accessory wire. Please follow the procedure
outlined below to make the proper connection.
1. This tech bulletin only needs to be followed if installing the RP4-NI11 into the 2014+ Nissan Rogue without an accessory wire in the main
20-pin harness.
2. It is important that all connections be soldered to ensure they are secure. Using T-Taps or crimp connectors will result in faulty connections
which could cause erratic/unreliable operation.
Installation Steps
1. Connect the main 20-pin and 24-pin harnesses as outlined in the instruction manual included with the interface.
2. Locate the light green accessory wire in the 24-pin Nissan factory harness (Fig. 1). This wire will need to be jumped to the red wire located in
pin 16 of the 20-pin RP4 harness (Fig 2).
RP4-NI11
Connector
Fig. 1
24-Pin Vehicle
Connector
Fig. 2
All connectors are viewed from wire side
Factory ACC Wire RP4 ACC Wire
© 2018 AAMP Global. All rights reserved. PAC is a Power Brand of AAMP Global.
PAC-audio.com
C
Page 1
Rev. 061118
Nissan Murano with Navigation
RP4-NI11 Hardwire
Technical Bulletin
Overview:
In order for the RP4-NI11 to operate in the 2015 and up Nissan Murano applications that are equipped with
navigation, several wires from the RP4-NI11 must be hardwired into the 40 pin harness at the radio. RP4-NI11
Revision 4 or higher of îš¿rmware is required.
Installation:
1. Follow the instructions from the
RP4-NI11 installation manual for the
wire connections from the RP4-NI11
into the aftermarket radio harness.
Only the primary 24 pin connector
and the black 16 pin RP4-NI11
connectors will be used (see Fig.1).
2. Cut the Pink (CAN +) and
Pink / Black (CAN -) wires between
the RP4-NI11 connector and where
the wires split to go to the 3 unused
connectors (see Fig. 1).
3. Connect the Pink wire (from step
2) to the Light Blue wire (CAN +) in
pin 41 of the 40 pin radio connector
(see Fig. 2).
4. Connect the Pink / Black wire (from
step 2) to the Light Green wire
(CAN -) in pin 21 of the 40 pin radio
connector (see Fig. 2).
5. Only necessary when using a
reverse camera: Locate the Green
(Reverse +) wire in the Black 16
pin RP4-NI11 connector that goes
to a junction near the (unused) 24
pin connector, with one side going
to the aftermarket radio wiring, one
side going to the (unused) 24 pin
connector, and one side going to the
(unused) 32 pin connector. Cut the
Green wire between the junction and
Cut for Non-Bose systems
Cut Pink and
Pink / Black
Cut Green
X
X
X
These Connectors
Not Used
This Connector
Is Used
Fig. 1
the (unused) 32 pin connector (see Fig. 1).
6. Connect the Green wire (from step 3) to the Green wire (Reverse +) in pin 45 of the 40 pin radio connector (see
Fig. 2).
Fig. 2
Connector Viewed From Wire Side
CAN - (Light Green) Rev + (Green)Pin 21 Pin 45
CAN + (Light Blue)Pin 41
Testing and Veriîš¿cation:
1. Turn on the ignition and press audio steering wheel control buttons to verify the LED on the RP4 NI11 ashes
to indicate that it recognizes the button commands. If the LED does not ash, verify the CAN + and CAN -
connections to the Pink and Pink / Black wires on the RP4-NI11, and verify the RP4-NI11 is using îš¿rmware
Revision 4 or higher.
2. Test the Green reverse output connector by verifying the wire is providing a 12 volt output when the ignition is on
and the vehicle is in reverse.
RP4-NI11
Radio Replacement & Steering Wheel Control Interface
for Nissan Vehicles
Paciîš¿c Accessory Corporation
® | Ph. 866-931-8021 | support@pac-audio.com
©2016 Pacic Accessory Corporation
www.pac-audio.com
Rev. 011116
C
Introduction & Features
Important Notes
Wiring Connection Chart
Illustration / Schematic
1. The radio select rotary switch on the side of the interface must be adjusted to the proper radio setting before plugging the
interface into the vehicle (see next page for setting chart).
2. The interface comes pre-programmed for all of the vehicles factory SWC functions and does not require programming unless
you wish to re-assign the SWC functions or utilize short press long press dual command functionality. The SWC can always
be restored to default settings by pressing and releasing the program button on the side of the interface once and waiting 7
seconds for the LED to ash 4 times.
3. Does not retain 360 camera system
4. In some 2014+ Nissan Rogues, it may be necessary to îš¿nd an alternate accesory 12v+ wire If the interface and aftermarket
radio are not powering up. Please see Appendix A on page 4 to îš¿nd an alternate accessory 12v+ wire.
Vehicle Connector SWC Connector
SWC Connection
See above chart for
different radio type
connections
Acc On/
Programming
LED
Programming
Button
Wiring SWC Connection
Yellow Battery +12v
Black Ground
Red Accessory 12v+
Purple / White Vehicle Speed
Output
Blue / White Amp Turn On Input
Orange / White Illumination Output
(+)
Green *Reverse Output (+)
White Front L + input
White / Black Front L - input
Grey Front R + input
Grey / Black Front R - input
Green Rear L + input
Green / Black Rear L - input
Purple Rear R + input
Purple / Black Rear R - input
Yellow RCA *Reverse Camera
Output
Blu/Yel Kenwwod, Newer
JVC
3.5mm Jack Alpine, JVC,
Clarion, Fusion,
Pioneer, Sony,
Boyo, Dual,
Lightning Audio,
Visteon or Advent
The RP4-NI11 interface allows the replacement of a factory radio in select Nissan vehicles with MSCAN databus radios.
Using this interface will retain factory features such as steering wheel controls (SWC), reverse camera and the factory
ampliîš¿er when the original radio is removed. Use of this interface also allows you to program two radio functions to each
SWC button by using short press long press dual command functionality. The RP4-NI11 also provides outputs such as
vehicle speed sensor (VSS), illumination and *reverse trigger.
* Only available in vehicles
equipped with a factory reverse
camera.
Cut f or Non-Bose systems
Aftermarket Radio Connections
See above chart for wire color
description.


Produktspezifikationen

Marke: PAC
Kategorie: Nicht kategorisiert
Modell: RP4-NI11

Brauchst du Hilfe?

Wenn Sie Hilfe mit PAC RP4-NI11 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Nicht kategorisiert PAC

Bedienungsanleitung Nicht kategorisiert

Neueste Bedienungsanleitung für -Kategorien-