PAC RP4-FD11 Bedienungsanleitung


Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für PAC RP4-FD11 (5 Seiten) in der Kategorie Nicht kategorisiert. Dieser Bedienungsanleitung war für 2 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/5
RP4-FD11
Radio Replacement & Steering Wheel Control Interface
for Ford/Lincoln/Mercury Vehicles
Pacic Accessory Corporation
® | Santa Ana, California 92705 | Ph. 866-931-8021 | support@pac-audio.com
©2011 Pacic Accessory Corporation
www.pac-audio.com
Rev. 112811
C
Introduction & Features
Important Notes
Wiring Connection Chart
The RP4-FD11 interface allows the replacement of a factory radio in select Ford/Lincoln/Mercury vehicles with MSCAN
databus radios. Using this interface will retain factory features such as steering wheel controls (SWC), rear seat
entertainment (RSE), Rear Seat Controls (RSC) and the THX or Sony amplier when the original radio is removed. The
RP4-FD11 also provides data bus driven outputs such as retained accessory power (RAP), vehicle speed sensor (VSS),
illumination, reverse trigger and parking brake.
1.The radio select rotary switch on the side of the interface must be adjusted to the proper radio setting
before plugging the interface into the vehicle (see below for setting chart).
2. The interface comes pre-programmed for all of the vehicles factory SWC functions and does not require programming unless
you wish to re-assign the SWC functions to different buttons. The SWC can always be restored to default settings by pressing
and releasing the program button on the side of the interface once and waiting 7 seconds for the LED to ash 4 times.
3. RSC & LCD buttons that are identical to the SWC will mimic the SWC one for one. All other buttons cannot be programmed.
4. The LED will ash whenever a SWC button is pressed.
5. The RSC must be in AM mode for Track +/- to function. RSC must be set to AUX mode to pass audio to aftermarket radio.
6. Vehicles equipped with a factory amplied system must disconnect SYNC if they wish to use the voice button. Not disconnecting
SYNC will result in the rear speakers muting every time the voice button is pressed.
7. Feeding too strong of an audio signal into the headrest monitors will cause the audio output to shut down. If this happens you
must turn the tv off and on and lower the audio signal.
Red / White P.B. Output (-)
Purple / White VSS Output
Blue / White Amp Turn On Input
Red Acc. Output (1 amp)
Orange / White Illum. Output (+)
Green Reverse Output (+)
Interface Connector
Yellow Battery +12v
Black Ground
Blue Antenna On Input
White Front L + input
White / Black Front L - input
Grey Front R + input
Grey / Black Front R - input
Green Rear L + input
Green / Black Rear L - input
Purple Rear R + input
Purple / Black Rear R - input
Vehicle Connector SWC Connector
Blu/Yel Kenwwod, Newer
JVC, OEM or
Blaupunkt
3.5mm Jack Alpine, JVC,
Clarion, Pioneer,
Sony, Valor, Boyo,
Dual, Visteon or
Advent
Page 1
RP4-FD11
Radio Replacement & Steering Wheel Control Interface
for Ford/Lincoln/Mercury Vehicles
Pacic Accessory Corporation
® | Santa Ana, California 92705 | Ph. 866-931-8021 | support@pac-audio.com
©2011 Pacic Accessory Corporation
www.pac-audio.com
Rev. 112811
C
Installation Steps
1. The radio select rotary switch on the side of the interface must be adjusted to the proper radio setting before plugging the interface
into the vehicle.
2. Make all connections as described in the connection chart on page 1.
3. If the vehicle is equipped with RSE plug the RCA cables labeled “RSE” into the aftermarket radios AUX input. The RSE RCA cables are
necessary to allow the headunit to play the RSE media audio through the cabin.
4. If the vehicle is equipped with a factory subwoofer plug the RCA cables connected to the 8 pin plug into the Subwoofer or Non-Fading output
of the aftermarket radio.
5. Connect the SWC wire according to the chart on page 1 (aftermarket radio MUST support a wired remote input).
6. If you wish to reassign functions to the SWC follow the programming instructions in the next section.
Illustration / Schematic
SET RADIO SELECT SWITCH
Alpine
Advent,
BOYO, Dual,
Visteon, Sony
Blaupunkt OEMClarion JVC Kenwood Pioneer Valor
1 7 8 4 2 3 6 7 5
1
2
3
4
5
6
7
8
9
0
IMPORTANT! If you wish to use the Voice, OK or Phone button in vehicles equipped with analog SWC you MUST wire them into
the RP4-FD11. The wires you need can be found by removing the steering wheel column and accessing the connector shown in
Fig. 1. Once you have located the plug you must cut the wires located in pins 4 & 6 as shown in Fig. 2 (Wire colors may vary by
vehicle). Finally you must connect the steering wheel side of pins 4 & 6 to the RP4-FD11 interface connector as shown in Fig. 3.
Connector
Pin 4
Pin 6
Cut Wires
SWC Connection
See above chart for
different radio type
connections
SWC Connection
AUX
AUX
RSE
RSE
SUB
SUB
Pacific Accessory Corporation
Interface Connector
See above chart for wire color descriptions.
Vehicle Connector
See above chart for wire color description.
Wiring
Fig. 1 Fig. 2
8
16 9
1
Connect steering wheel side of
pin 4 to the grn/wht wire in
pin 4 of the RP Interface plug
Connect steering wheel side of
pin 6 to the black wire in
pin 11 of the RP Interface plug
Fig. 3
Page 2
RP4-FD11
Radio Replacement & Steering Wheel Control Interface
for Ford/Lincoln/Mercury Vehicles
Pacic Accessory Corporation
® | Santa Ana, California 92705 | Ph. 866-931-8021 | support@pac-audio.com
©2011 Pacic Accessory Corporation
www.pac-audio.com
Rev. 112811
C
Optional Steering Wheel Control Programming
IMPORTANT! The interface comes pre-programmed for the functions listed in the chart below and does not require programming
unless you wish to re-assign the SWC functions to different buttons. The SWC can always be restored to default settings by
pressing the program button on the side of the interface once and waiting for the timeout.
A
r
If you wish to re-assign the SWC functions, the interface must be programmed in the specic order shown in the chart below If you
come across a function in the chart that your steering wheel does not have, or you do not want to program, press and release the
program button on the side of the interface to skip that function. The LED will ash off and on conrming that you have successfully
skipped that function and are ready to proceed to the next one.
Alpine JVC Kenwood Clarion
V
alo
r
OEM Sony/Pionee
r
Blaupunkt
V
olume + Volume + Volume + Volume + Volume + Volume + Volume + Volume + Volume +
V
olume - Volume - Volume - Volume - Volume - Volume - Volume - Volume - Volume -
Media Source Source Source Source Source Source Source Source
Track + Track + Track + Track + Search + Track + Track + Track + Track +
Track - Track - Track - Track - Search - Track - Track - Track - Track -
V
oice Mute Attenuation Mute Mute Mute Mute Mute Mute
Phone Receive Phone Receive Answer Send/End Cursor Up Answer Answer Call Disc Up
OK Ent/Pl
y
Selec
t
Pla
y
Band OK Play/O
K
Phone Menu OK
SET RADIO SELECT SWITCH
Alpine
Advent,
BOYO, Dual,
Visteon, Sony
Blaupunkt OEMClarion JVC Kenwood Pioneer Valor
1 7 8 4 2 3 6 7 5
1
2
3
4
5
6
7
8
9
0
Optional Programming Order
Default SWC Button Assignments
Page 3


Produktspezifikationen

Marke: PAC
Kategorie: Nicht kategorisiert
Modell: RP4-FD11

Brauchst du Hilfe?

Wenn Sie Hilfe mit PAC RP4-FD11 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Nicht kategorisiert PAC

Bedienungsanleitung Nicht kategorisiert

Neueste Bedienungsanleitung für -Kategorien-