PAC RP4-CH21 Bedienungsanleitung

PAC Nicht kategorisiert RP4-CH21

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für PAC RP4-CH21 (4 Seiten) in der Kategorie Nicht kategorisiert. Dieser Bedienungsanleitung war für 7 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF
Seite 1/4
Pacic Accessory Corporation
® | Santa Ana, California 92705 | Ph. 866-931-8021 | support@pac-audio.com
©2014 Pacic Accessory Corporation
www.pac-audio.com
C
RP4-CH21
Radio Replacement & Steering Wheel Control Interface
for Dodge/Jeep/Ram Vehicles
Rev. 043014
Page 1
Introduction & Features
Important Notes
The RP4-CH21 interface allows the replacement of a factory radio in select Dodge/Jeep/Ram vehicles with MS-CAN
databus radios. Using this interface will retain factory features such as steering wheel controls (SWC), HVAC controls,
Driver Information Center (DIC), vehicle settings, vehicle safety features and the factory audio amplier whenever the
original radio is removed. Use of this interface also allows you to program two radio functions to each SWC button by
using short press long press dual command functionality. The RP4-CH21 also provides data bus driven outputs such as
retained accessory power (RAP), vehicle speed sensor (VSS), illumination, reverse trigger and parking brake.
1. Please make your vehicle settings selections before removing the factory radio for optimal installation time. Once the radio has
been removed, the vehicle settings which are normally selected through the factory radio can be accessed by downloading
and installing the PAC Vehicle Settings program from . A PAC-UP is http://www.pac-audio.com/rmware/RP/index.html
required to connect with the interface. Please see page 6 for further details on the vehicle settings app.
2. Vehicles with a factory amplier: The factory amplier only accepts two channels of audio input (left and right). Fading is
not supported in these applications. The factory amplier’s fading is controlled by data communication from the factory radio.
Neither the aftermarket radio or the RP interface have the ability to control the amplier’s fader.
3. Vehicles equipped with VES: Retention of the VES system is not currently supported
4. The active guide lines for the factory reverse camera can be turned off and on in the vehicle settings app referenced above.
5. In vehicles equipped with the 8.4” uConnect system, the factory compass display on the DIC, 911 assist, WiFi hotspot and
uConnect access will be lost.
6. The radio select rotary switch on the side of the interface must be adjusted to the proper radio setting before plugging the
interface into the vehicle (see next page for setting chart).
7. The interface comes pre-programmed for all of the vehicles factory SWC functions and does not require programming unless
you wish to re-assign the SWC functions or utilize short press long press dual command functionality. The SWC can always
be restored to default settings by pressing and releasing the programming button on the side of the interface once and waiting
7 seconds for the LED to ash 4 times.
8. The LED will ash whenever a programmable SWC button is pressed.
9. uConnect is not retained when using this interface
10. RAM Promaster equipped with a single DIN radio is not compatible
11. Dodge Durango - You will lose the button from radio to ip down third row headrests. Users will have to control rear climate
controls from the controls located in the rear roof. Ventilated seats are not supported.
12. Jeep Grand Cherokee: Ventilated seats are not supported
13. Jeep Cherokee: Ventilated seats are not supported
14. All vehicle settings will be retained, however the following settings are not adjustable once the factory radio is removed:
• RAM Trucks/Grand Cherokee/Durango
• Fuel Saver Display
• Air Suspension Settings
• Forward Collision Warning with Crash Mitigation
• Cherokee (With Technology Package)
• Adaptive Cruise Control with Stop and Go
• Advanced Brake Assist
• Automatic High Beam Headlamp Control
• Blind Spot and Cross Path Detection
• Forward Collision Warning with Crash Mitigation
• LaneSense Lane Departure Warning
• Parallel and Perpendicular Park Assist
• Rain Sensitive Windshield Wipers
• Tilting Side Mirrors While in Reverse
• Power Lift Gate Chime
Pacic Accessory Corporation
® | Santa Ana, California 92705 | Ph. 866-931-8021 | support@pac-audio.com
©2014 Pacic Accessory Corporation
www.pac-audio.com
C
RP4-CH21
Radio Replacement & Steering Wheel Control Interface
for Dodge/Jeep/Ram Vehicles
Rev. 043014
Page 4
Optional Steering Wheel Control Programming (cont)
Radio Alpine JVC Kenwood Clarion Other* Pioneer Sony Fusion
1 Volume + Volume + Volume + Volume + Volume + Volume + Volume + Volume +
2 Volume - Volume - Volume - Volume - Volume - Volume - Volume - Volume -
3 Mute Mute Mute Mute Mute Mute Mute Mute
4 Preset + Source Source Source Preset + Preset + Preset + Source
5 Preset - Track + Play Search + Preset - Preset - Preset - Track +
6 Source Track - Track + Search - Source Source Source Track -
7 Track + Band/Disc + Track - Band Track + Track + Track + Audio
8 Track - Preset/Disc - Disc/FM + Send/End Track - Track - Track - Power
9 Power Select Disc/AM - Send Band Band Band
10 Enter/Play Attenuation Answer End Phone Menu
Reject Call/Source
(Bluetooth equipped
radios only)
11 Band/Program Phone Receive Voice Dial Answer Call Answer/End Call
12 Receive Phone Reject On Hook End Call
13 End Voice Dial Off Hook Voice Activation
14 Power Mute (Multimedia
units only)
*Other = Advent, Boyo, Dual, Lightning Audio, Rockford Fosgate, & Visteon
Optional Programming Order
Programming
1. Turn the key to the ignition position.
2. Press and release programming button on the side of the interface.
3. Within 7 seconds, press the button that is to be learned on the steering wheel. The LED will turn off when the button is pressed.
At this point you have two options:
A. For short press functionality: Release the button within 1.5 seconds. The LED will turn back on.
B. For long press functionality: Hold the button until the LED starts blinking. Release the button and the LED will
go back to solid.
4. If you need to program more buttons, repeat step 3 for each additional audio function on the steering wheel.
5. If you come across a function in the chart that your steering wheel does not have, or you do not want to program, press and
release the program button on the side of the interface to skip that function.
6. Once programming is completed, wait seven seconds. The LED will ash three times indicating end of programming.
7. Test the interface for proper functionality. Whenever a SWC is pressed the LED on the interface should blink. If any function
does not work, repeat the programming steps
1
2
3
4
5
6
7
8
9
0
Alpine JVC Kenwood Clarion Pioneer/Other Sony Fusion
1 2 3 4 7 8 9
Other = Advent, BOYO, Dual, Lightning Audio, Rockford Fosgate, Visteon
SET RADIO SELECT SWITCH
RP4-CH21 SWC Notes
1. In vehicles that do not have SWC for the radio but do have
SWC for the menu you can program the up/down/left/right
arrows to whatever you want. We recommend that you
have the DIC in the speedometer screen when using the
SWC for the radio (Fig.1)
2. The Mute, Answer and End buttons in the Ram Promaster
can not be programmed for long press functionality.
Fig. 1
Pacic Accessory Corporation
® | Santa Ana, California 92705 | Ph. 866-931-8021 | support@pac-audio.com
©2014 Pacic Accessory Corporation
www.pac-audio.com
C
RP4-CH21
Radio Replacement & Steering Wheel Control Interface
for Dodge/Jeep/Ram Vehicles
Rev. 043014
Page 5
Testing & Verication
1. Turn the ignition on. The LED on the interface will turn on & the +12v accessory wire will turn on.
2. Turn on the radio & check balance & fade. Note: will not fade as neither the aftermarket radio Factory amplied Systems
or the RP interface have the ability to control the amplier’s fader.
3. Verify that the factory subwoofer (if present) is playing
4. Verify that all SWC are functioning properly.
5. Turn off vehicle & remove key. RAP will be active & keep the radio on for up to 10 minutes (depending on the user
programmed vehicle setting) or until the drivers door is opened.
6. The LED & radio will turn off when RAP turns off or the drivers door is opened.
Additional Controls
When replacing the radio in the following vehicles you may lose some of the climate control features that the factory radio provides:
Grand Cherokee, Cherokee, Ram & Durango. The RP4-CH21 retains those features by integrating them into the existing factory
buttons and displaying the information on the DIC. PLEASE NOTE: The DIC must be set to Audio mode in order for the HVAC
information to be displayed.
The following buttons have been re-purposed from their original OEM function to retain key HVAC controls that are missing when
removing the factory radio:
• Mute Button - Sets Max A/C On/Off
• Enter Button - Locks out rear zone climate controls (Durango only)
• Screen Off Button - Sets fan position (Defrost/Vents/Floor)
• Back Button - Syncs temperatures for dual zone climate controls
• The lock buttons on the doors control their respective seat heaters. Press and hold lock for 2 seconds to engage seat heater.
Press lock again to change from high/low/off. The status will displayed on DIC.
• The assist button on mirror turns heated steering wheel on/off. The status will displayed on DIC.
• HVAC buttons that remain retain their original OEM functionality
Volume Knob & Tune Knob - Work one for one with the SWC
Mute Button –
Sets Max A/C. On/O
Screen O Button -
Sets fan position.
Back - Sync temps
for dual zone climate
control.
Enter - Locks out rear
zone climate control.
Setting the Clock in the Promaster (Must be done with radio off)
1. Press and hold volume down on the SWC.
2. While holding volume down, use the track up/down buttons on the SWC to adjust the time.
Setting the Date in the Promaster
1. Press and hold volume up on the SWC.
2. While holding volume up, use the track up/down buttons on the SWC to adjust the date.
3. The 12/24 hour setting will have to be adjusted using the vehicle settings app referenced on the next page.

Produktspezifikationen

Marke: PAC
Kategorie: Nicht kategorisiert
Modell: RP4-CH21

Brauchst du Hilfe?

Wenn Sie Hilfe mit PAC RP4-CH21 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten


Bedienungsanleitung Nicht kategorisiert PAC

PAC

PAC RP4-GM31 Bedienungsanleitung

6 September 2024
PAC

PAC NU-GM51 Bedienungsanleitung

6 September 2024
PAC

PAC NAV-1129 Bedienungsanleitung

6 September 2024
PAC

PAC LP7-2R Bedienungsanleitung

6 September 2024
PAC

PAC LP7-4 Bedienungsanleitung

6 September 2024
PAC

PAC GMK367B Bedienungsanleitung

6 September 2024
PAC

PAC CP1-FRD1 Bedienungsanleitung

6 September 2024
PAC

PAC C2A-CHY5 Bedienungsanleitung

6 September 2024
PAC

PAC NU-GM3 Bedienungsanleitung

6 September 2024
PAC

PAC CP1-TSL1 Bedienungsanleitung

6 September 2024

Bedienungsanleitung Nicht kategorisiert

Neueste Bedienungsanleitung für -Kategorien-

DAS Audio

DAS Audio AX-112-5 Bedienungsanleitung

16 Oktober 2024
Ferplast

Ferplast Ergocomfort Freetime Bedienungsanleitung

16 Oktober 2024
AEG

AEG MECK52 Bedienungsanleitung

16 Oktober 2024
Makita

Makita UR012G Bedienungsanleitung

16 Oktober 2024
Stihl

Stihl HT 70 Bedienungsanleitung

16 Oktober 2024
Ernesto

Ernesto H14270 Bedienungsanleitung

16 Oktober 2024
IFM

IFM AC901S Bedienungsanleitung

16 Oktober 2024
Nedis

Nedis RFPOM120FBK Bedienungsanleitung

16 Oktober 2024
AEG

AEG E9KLCS01 Bedienungsanleitung

16 Oktober 2024
ART

ART ProChannel II Bedienungsanleitung

16 Oktober 2024