PAC RP3-GM12 Bedienungsanleitung


Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für PAC RP3-GM12 (2 Seiten) in der Kategorie Nicht kategorisiert. Dieser Bedienungsanleitung war für 15 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/2
RP3-GM12
Radio Replacement Interface for General Motors Vehicles
Pacifi c Accessory Corporation® | Santa Ana, California 92705 | Ph. 866-931-8021 | support@pac-audio.com
©2013 Pacifi c Accessory Corporation
www.pac-audio.com
Rev. 11-22-13
3
3
3
Introduction & Features
Wiring Connection Chart
Illustration / Schematic
The RP3-GM12 interface allows the replacement of a factory radio in select General Motors vehicles with Class II radios. Using
this interface will retain factory features such as Warning Chimes when the original radio is removed. The RP3-GM12 provides
data bus driven outputs such as retained accessory power (RAP), vehicle speed sensor (VSS), illumination, reverse trigger and
parking brake. The RP3-GM12 also provides a secondary output for adding an optional PAC Steering Wheel Control (SWC)
retention interface (SWI-RC, SWI-PS, SWI-JACK, SWI-ECL2 or SWI-X).
Red / White Parking Brake
Output (-)*
Purple / White Vehicle Speed
Output*
Blue / White Amp Turn On Input
Red Accessory Output
(10 amp)
Orange / White Illumination Output
(+)*
Green Reverse Output (+)*
Interface Connector
Yellow Battery +12v
Black Ground
Blue Antenna On Input
White Front L + input
White / Black Front L - input
Grey Front R + input
Grey / Black Front R - input
Green Rear L + input
Green / Black Rear L - input
Purple Rear R + input
Purple / Black Rear R - input
Vehicle Connector
*Not all radios will have these
connections. Please insulate
these wires when not used.
Chime Volume Adjustment
Aftermarket Radio
Connections
Connect to SWC
Interface. Program
for Version 2.
To optional SWC interface
To Vehicle
Connector Acc On
LED
Important Notes
1. For BOSE systems, the recommended line level input is between 2-4 volts from the aftermarket radio.
2. To prevent over driven audio when installing into a vehicle with a BOSE system and the aftermarket radio does not have low
level outputs then an LOC (part # SOEM-4 or LP3-4) is recommended to match the input voltage.
3. Use the 4 position selector switch located on the side of the interface to select the best chime output for your speci c installation.
RP3-GM12
Radio Replacement Interface for General Motors Vehicles
Pacifi c Accessory Corporation® | Santa Ana, California 92705 | Ph. 866-931-8021 | support@pac-audio.com
©2013 Pacifi c Accessory Corporation
www.pac-audio.com
Rev. 11-22-13
3
3
3
Steering Wheel Control Output Connector
Testing & Veri cation
Product Updates (Firmware)
1. The RP3 provides a SWC output connector attached
to the harness. For ease of installation, all necessary
connections for an SWI have been made for you.
2. When using this SWC output connector the SWC
interface must be programmed for version 2 .
(refer to SWC interface programming instructions for
exact programming sequence).
3. Both loops should remain in tact.
4. During steering wheel button assignment programming
the vehicle should be running and each button should
be pressed and held for at least 5 seconds. Please refer
to the SWI manual for button assignment order.
1. Turn the ignition on. The LED on the interface will turn on & the +12v accessory wire will turn on.
2. Turn on the radio & check balance & fade.
3. Verify that the factory subwoofer (if present) is playing
4. If an optional SWC retention interface was used, verify that all SWC are functioning properly.
5. Turn off vehicle & remove key. RAP will be active & keep the radio on for 10 minutes or until the drivers door is opened.
6. The LED & radio will turn off when RAP turns off or the drivers door is opened.
7. Use the 4 position selector switch located on the side of the interface to select the best chime output volume for your specifi c
installation. Setting 1 being loudest and 4 softest.
The RP3-GM12 can be updated with new fi rmware as it becomes available using the PAC-UP interface updater (sold separately).
Please visit www.pac-audio.com/fi rmware for available updates.
Aftermarket Radio
Connections
To Vehicle
Connector
Connect to SWC
Interface. Program
for Version 2.
To optional SWC interface
Chime Volume Adjustment
1
4
2
3
Installation Steps
1. It is extremely important to makes sure the ignition is off and the drivers door open before connecting the interface to the vehicle.
2 Make all connections as described in the chart on page 1. The audio level will vary depending on the new radios pre-amp output
voltage (2-4 volts is recommended).
3. Follow the instructions below if you wish to add an optional SWC retention interface.


Produktspezifikationen

Marke: PAC
Kategorie: Nicht kategorisiert
Modell: RP3-GM12

Brauchst du Hilfe?

Wenn Sie Hilfe mit PAC RP3-GM12 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Nicht kategorisiert PAC

Bedienungsanleitung Nicht kategorisiert

Neueste Bedienungsanleitung für -Kategorien-