PAC HDK001X Bedienungsanleitung


Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für PAC HDK001X (4 Seiten) in der Kategorie Nicht kategorisiert. Dieser Bedienungsanleitung war für 13 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/4
Page 1
HDK001X
Aftermarket Stereo Dash Kit for
Select Harley-Davidson Motorcycles
Pacic Accessory Corporation
® | 866-931-8021 | support@pac-audio.com
©2016 Pacic Accessory Corporation
www.pac-audio.com Rev. 012016
P ifi A C ti
PAC is an AAMP brand
Parts List
The HDK001X includes everything you will need for proper mounting of an aftermarket radio into
the dash of your motorcycle. This kit contains the following parts:
1. Dash Kit
• (x2) Face plates (one is equipped with a splash guard)
• (x2) Mounting Brackets (one left and one right)
• (x4) Stainless steel bolts (short)
• (x4) Stainless steel nuts
• (x2) Spacers (used for Road Glide models only)
• (x4) Stainless steel bolts (long - for use with spacers)
2. Rubber Gasket Ring
3.Wiringharness(pre-wiredwithpower,speaker&SWI-HDspecicconnector)
4.SWI-HD(pre-programmedwithcustomHarleyrmware-noinitialprogrammingnecessary)
Required Tools
The following is a list of tools (not included) you will need to complete this installation.
• T-25 Torx driver
• T-27 Torx driver
• 3/16” or 5mm Hex Socket
• 1/4” or 6mm long shaft Hex Socket
• 7/16” Socket/ratchet combo or box wrench (Road Glide models only)
Fairing Disassembly
0
20
30
70
80
40
50
60
10
0
10
30
20
50
40
110
120
60 70
80
90
100
MPH
H
A
R
L
E
Y
-
D
A
V
I
D
S
O
N
C
E
R
T
I
F
I
E
D
RPM
x100
H
A
R
L
E
Y
-
D
A
V
I
D
S
O
N
1
2
3
4 5
76
Removal of the outer fairing and windshield:
1. Drape front fender area with protective material/
pad to prevent scratching or damaging the paint.
2. From the front of the motorcycle, loosen the three
T27 TORX screws located (Numbered 1, 2 & 3 on
illustration) below the windshield.
3. Raise and remove the windshield from the inner
and outer fairings.
4. Remove the two T27 TORX screws located on
outer sides of the speakers (Numbered 4 & 5 on
illustration).
5. Turn the handlebar to the right and remove the
T-27 TORX screw (Number 6) by reaching below
the left side of the fairing cap.
6. Turn the handlebar to the left and remove the T-27
TORX screw (Number 7) by reaching in below the
right side of the fairing cap.
CAUTION: When working on FLHX models, be sure
to hold the outer fairing in place when removing the
last screw. Without the auxiliary lamps to hold it
in place, the outer fairing will drop and can cause
damage to the fairing or fender.
7. From the front of the motorcycle, remove the three
screws below the windshield. (Previously loosened
in step 2)
8. Tilting the outer fairing forward, remove head lamp
connector at the back of the head lamp assembly.
9. Lift the outer fairing off the motorcycle.
2006-2013 FLHX Street Glide & 1996-2013 FLHT Electra Glide Models
FLTR (Road Glide) instructions on next page
Page 2
HDK001X
Aftermarket Stereo Dash Kit for
Select Harley-Davidson Motorcycles
Pacic Accessory Corporation
® | 866-931-8021 | support@pac-audio.com
©2016 Pacic Accessory Corporation
www.pac-audio.com Rev. 012016
P ifi A C ti
PAC is an AAMP brand
Fairing Disassembly: (cont.)
1998-up FLTR Road Glide Models
Remove the outer fairing and windshield as follows:
NOTE: Windshield may be left in place during outer fairing removal.
1. Drape front fender area with protective material/pad to prevent
scratching or damaging the paint.
2. Remove the two T-25 Torx screws located at the outer edge of the
fairing next to the left and right speakers (Numbers 3 & 4 of Image
A).
3. Loosen the two T-25 Torx screws located at the top left and right
corners of the fairing next to the fuel and volt gauges, respectively
(Numbers 1 & 2 of Image A).
4. Remove the two T-25 Torx screws just below left and right side
glove compartments (Numbers 5 & 6 of Image A).
5. On inboard side of right fairing support, remove the two rear acorn
nuts (Image B) from the studs of front turn signals (left and right).
Pull front turn signal lamp assembly from the motorcycle and allow
it to hang from the front of engine guard.
6. Remove the top left and right screws next to the fuel and volt
gauges previously loosened in step #3.
7. Raise outer fairing slightly and then rest on protective fender pad.
8. Squeeze two external tabs to disconnect headlamp jumper har-
ness connector.
9. To avoid possible wire damage, disconnect front turn signal lamp
connectors and place in safe area.
0
20
30
70
80
40 50
60
10
RPM x100
0
10
30
20
50
40
110
120
60 70
80
90
100
MPH
H
A
R
L
E
Y
-
D
A
V
I
D
S
O
N
M
O
T
O
R
C
O
M
P
A
N
Y
CERTIFIED
HA R L EY-DAVIDSON
H
A
R
L
E
Y
-
D
A
V
I
D
S
O
N
M
O
T
O
R
C
O
M
P
A
N
Y
5
3
12
4
6
Image A
Image B
Remove the radio from the dash cavity as follows:
1. Disconnect and remove the CB module (Number 4 of image C, if
equipped) from the factory radio. To do this disconnect the CB
antenna and the 12-pin connector from the CB module. Once the
connectors have been detached, remove the screw to separate
the CB module from the radio.
2. Disconnect the radio connectors behind the radio (See Image C).
NOTE: Not all motorcycles are equipped with connector #2.
3. Using a long shank ball end socket, remove four 6mm hex bolts
(two on right, two on left) to release radio or storage (FLHT) from
left and right radio support brackets. Use oblong holes on brackets
to access screws. (See Image D to the right for reference).
4. Pull radio or storage box (FLHT) forward (towards front) to remove
from opening in the inner fairing.
24
31
Image C
Image D
Radio Removal
Page 3
HDK001X
Aftermarket Stereo Dash Kit for
Select Harley-Davidson Motorcycles
Pacic Accessory Corporation
® | 866-931-8021 | support@pac-audio.com
©2016 Pacic Accessory Corporation
www.pac-audio.com Rev. 012016
P ifi A C ti
PAC is an AAMP brand
Kit Assembly
1. Decide which main frame (faceplate) to use for installa-
tion (with or without the splash guard).
2. Install the side brackets to rear of main frame.
3. Insert the stainless steel nuts (provided) to the side brackets.
They are sized to t snug in the hex openings. NOTE:
Some force may be required to seat them all the way in
the openings.
4. Insert an ISO mountable single DIN radio between the
left and right ISO mount brackets and loosely attach to
sides of the radio using the screws provided with radio
when possible, or use the screws supplied with kit.
5. Using the main frame of the HDK001X as a guide, slide
radio forward or backward to desired depth/look and then
tighten screws to the radio. If the main frame with splash
guard is used for installation, ensure the hinged door
opens and shuts properly before tightening of the screws
to the radio.
6. Slide the included rubber gasket onto the front edge of
the main frame being used.
7. Insert the kit and radio combo into the factory radio open-
ing from the back side of the inner fairing.
8. If the kit does not t snug between the radio mounting
brackets then the optional spacers (included) may need
to be used.
9. Secure the kit and radio combo using the supplied hard-
ware (use the short screws, or longer screws if spacers
were used).
Harness & Module Overview
HD-SWI-HAR
SWI-HD
Wire Color Function
Yellow Constant +12v
Red Accessory
Black Ground
White Left Front Speaker +
White/Black Left Front Speaker -
Grey Right Front Speaker +
Grey/Black Right Front Speaker -
Vehicle Connector
SWI-HD Module
Wire Color Function
Blue/Yellow Kenwood, Newer JVC or OEM
3.5mm Jack Advent, Alpine, Boyo, Clarion, Dual, Fusion, JVC, Lightning Audio, Pioneer, Sony,
Valor and Visteon


Produktspezifikationen

Marke: PAC
Kategorie: Nicht kategorisiert
Modell: HDK001X

Brauchst du Hilfe?

Wenn Sie Hilfe mit PAC HDK001X benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Nicht kategorisiert PAC

Bedienungsanleitung Nicht kategorisiert

Neueste Bedienungsanleitung für -Kategorien-