PAC APSUB-FD21 Bedienungsanleitung


Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für PAC APSUB-FD21 (5 Seiten) in der Kategorie Nicht kategorisiert. Dieser Bedienungsanleitung war für 6 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/5
© 2020 AAMP Global. All rights reserved. PAC is a Power Brand of AAMP Global.
PAC-Audio.com
C
Page 1
Rev: V1
Date: 091120
Advanced Subwoofer Ampliîš¿er Interface
for Select Ford Vehicles
APSUB-FD21
The APSUB-FD21 provides a 2-channel non-fading pre-amp output for use with an aftermarket ampliîš¿er and
subwoofer. Using the full range, îš¿xed level head unit output, in conjunction with CAN messages, the APSUB-FD21
delivers a low pass variable 5v RMS pre-amp output with bass equalization and level control capabilities. The signal
has a 350Hz / 24dB Linkwitz-Riley low pass îš¿lter applied. A data controlled remote ampliîš¿er turn on wire is also
provided by the APSUB-FD21.
Introduction and Features
Important Notes
1. This interface is only compatible in vehicles equipped with a data bus controlled premium sound system. To verify
compatibility, look for a Sony badge on the door speakers, center speaker, or factory subwoofer, in the 2019-2020
Super Duty trucks and Mustang; look for a B&O badge.
2. The factory ampliîš¿er must remain connected, and in the vehicle after the APSUB-FD21 has been installed.
3. The remote output is rated at 2A of current. If more current is needed an external relay must be used.
4. The remote output may remain active once the key has been removed if the vehicle needs to pass chime or SYNC audio.
5. The subwoofer outputs are non-fading. The output level of the subwoofer channel can be controlled using the supplied level
control knob. If the level control knob is not connected the output level will default to 100%.
6. The minimum volume level is set to a default. If you are happy with this level in your particular application then additional
adjustment is not required. Please refer to the Setup and Conîš¿guration section on page 2 for more details.
7. Ford Focus: You cannot use the steering wheel controls to activate the minimum volume adjustment.
8. The level control knob must be connected in order to manually adjust the minimum volume settings.
9. The factory radio's speed controlled volume and surround sound mode are not supported by the APSUB-FD21 outputs.
10. No adjustments can be made manually using the programming button, or the factory SWC when the module is connected to
a PC.
To Aftermarket
Amplier
Subwoofer Outputs
Remote Turn On Output
2A Max Output
To Vehicle
Harness
To Radio
To LCD
Screen
Non-Fading
Level Control
Knob
To Vehicle
Harness
AP4-FD21-HAR
The aftermarket ampliîš¿er must have a very solid ground and the ampliîš¿er power/ground connections
should be made before connecting the RCA's or Remote Turn On to the APSUB-FD21
© 2020 AAMP Global. All rights reserved. PAC is a Power Brand of AAMP Global.
PAC-Audio.com
C
Page 2
Rev: V1
Date: 091120
Advanced Subwoofer Ampliîš¿er Interface
for Select Ford Vehicles
APSUB-FD21
Setup and Conîš¿guration
1. Turn the ignition on. LED 1 on the interface will turn on and the +12v remote output will turn on.
2. Set the amp gain(s) to the desired level. We recommend using an oscilloscope and test tones to set the amp gain(s).
Please refer to the MECP Advanced study guide (p. 360) if you are unfamiliar with this process.
3. Check volume, balance, fade and EQ settings.
4. If you would like to adjust the minimum volume, do so using one of the methods outlined below. If you are happy with the
default level, no adjustments are necessary.
Manually Setting the Minimum Volume
If the minimum volume of the radio (factory radio volume level 1) is too loud, you can manually set the level of the minimum
volume using either the programming button on the side of the interface or the factory SWC. If you would like to set the
minimum volume using the AmpPRO app, please proceed to the AmpPRO App section.
Installation
Module Layout
Interface Connector 1
Expansion Port
Programming Button
Feature Select
DIP switches
Non-Fading Level Control
Knob Connection
USB Connection
LED 1
Subwoofer Output
LED 2
1. Remove factory radio and LCD screen.
2. Disconnect the 52-pin harness from the LCD screen and the 24-pin harness from the radio.
3. Connect APSUB harnesses to vehicle harnesses.
4. Connect APSUB harnesses to LCD screen and factory radio.
5. Set any feature DIP switches that apply to your install.
a. Set DIP switch 2 on (down) to lower the RCA output voltage to 4v. Leave DIP switch 2 off (up) to keep the RCA output
voltage at 5v.
b. DIP switch 1 is not used. DIP switches 3 and 4 are used for additional troubleshooting. (See page 5 for more details).
6. Connect the APSUB harness to the module.
7. Connect the level control knob to the module and install in an accessible location.
8. connect the signal cables and remote input from the After the aftermarket ampliîš¿er power/ground connections are made,
aftermarket ampliîš¿er to the APSUB.
9. Reconnect any additional harnesses removed from the radio and reinstall the radio.
DIP
1234
ON
No Function Troubleshooting* Troubleshooting*5v / 4v Preout
1 2 3 4
Set DIP switches to the ON position to activate the corresponding features.
Set DIP switches to the OFF position for any features that are not desired.
* See troubleshooting section on page 5 for more details
© 2020 AAMP Global. All rights reserved. PAC is a Power Brand of AAMP Global.
PAC-Audio.com
C
Page 3
Rev: V1
Date: 091120
Advanced Subwoofer Ampliîš¿er Interface
for Select Ford Vehicles
APSUB-FD21
Setup and Conîš¿guration (cont.)
Setting the minimum volume using the programming button
1. Start with the level control knob turned all the way down (counter-clockwise).
2. Set the amp gains to the desired level.
3. Set the volume on the factory radio to 1.
4. Press the programming button on the side of the interface once.
5. LED 1 will turn amber and the chimes will begin sounding every îš¿ve seconds.
6. Turn the level control knob clockwise until the desired minimum volume level is reached.
7. You can now either press the programming button once or wait ten seconds to exit the settings.
Setting the minimum volume using the factory SWC (This method not available in Focus)
1. Start with the level control knob turned all the way down (counter-clockwise).
2. Set the amp gains to the desired level.
3. Set the volume on the factory radio to 1.
4. The radio will Press and hold the track up button on the factory SWC for approximately ten seconds. PLEASE NOTE:
respond to the SWC commands during this process, this is normal and has no effect on the APSUB operation.
5. LED 1 will turn amber and the chimes will begin sounding every îš¿ve seconds.
6. Turn the level control knob clockwise until the desired minimum volume level is reached.
7. You can now either press the programming button once or wait ten seconds to exit the settings.
AmpPRO App
PLEASE NOTE: These settings can be adjusted with the module installed in the vehicle, or on the bench. However, it is
recommended to make the adjustments with the module installed, and the factory radio on, so that the changes can be
heard.
Minimum Volume Level - This allows you to set the minimum volume level of the factory radio (factory radio volume level 1).
EQ Enabled - This allows you to enable / disable the bass band factory EQ from adjusting the APSUB output.
Bass Freq / Q Factor - This allows you to set the center frequency that will be adjusted when setting the bass band on the
factory EQ, as well as the Q Factor for the frequency. The Q Factor determines how many of the adjacent frequencies will be
affected when adjusting the selected frequency. The lower the Q Factor, the more frequencies will be affected. See next page
for available frequencies and Q Factors. Note: This setting only affects the output of the APSUB and does not change the way
that the factory EQ adjusts the factory speakers.
Use of the AmpPRO PC App
allows you to do the following:
• Congure User Interface Options such as:
• Minimum Volume Level
• Enable / Disable Factory EQ
• Set Bass Center Frequencies and Q Factor
• Update Product Firmware
• Read Firmware / Hardware Versions
• You can download the AmpPRO app at :
https://pac-audio.com/app-downloads/
PLEASE NOTE: Level control knob must be connected to module for either of the following methods.


Produktspezifikationen

Marke: PAC
Kategorie: Nicht kategorisiert
Modell: APSUB-FD21

Brauchst du Hilfe?

Wenn Sie Hilfe mit PAC APSUB-FD21 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Nicht kategorisiert PAC

Bedienungsanleitung Nicht kategorisiert

Neueste Bedienungsanleitung für -Kategorien-