PAC APH-TY04 Bedienungsanleitung


Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für PAC APH-TY04 (2 Seiten) in der Kategorie Nicht kategorisiert. Dieser Bedienungsanleitung war für 10 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/2
Speaker Connection Harness for Select
Toyota and Lexus Vehicles with Factory Ampliîš¿ers
Equipped with a 10-Pin and 12-Pin Connector
APH-TY04
C
Page 1
Copyright © 2019. All rights reserved. PAC is a Power Brand of AAMP Global.
PAC-audio.com
Rev: V1
Date: 010419
Introduction and Features
The APH-TY04 simpliîš¿es speaker wire connections when adding aftermarket ampliîš¿ers. Aftermarket ampliîš¿ers can
be easily added with no need to cut or modify a vehicle’s original wiring. Each pair of wires has been labeled with the
corresponding speaker name.
Wiring Overview
Installation Notes
1. It is always best to use a tone generator (PAC part number: TL-PTG2) to verify that the tables in this manual, and the labels
on the wires, match the wiring in your speciîš¿c vehicle. This is important as there are instances where different trim levels of
the factory system may have the speaker outputs in different locations.
2. Any factory ampliîš¿er connectors other than the 10-pin and 12-pin connectors used by the APH-TY04, must remain
connected to the factory ampliîš¿er when using a PAC AmpPRO Interface. The PAC AmpPRO Interface will not operate
properly without them connected.
3. Not all applicable vehicles will come equipped with a corresponding speaker for all of the wires populated in our harness. It
is important to understand which speakers are equipped in your vehicle.
4. If you are leaving any of the factory speakers connected to the factory ampliîš¿er, simply connect the speaker wires (color for
color) between the male and female connectors, for the speakers that will be powered by the factory ampliîš¿er. For example:
If you want the rear speakers to be powered by the factory ampliîš¿er, simply connect the Green, Green / Black, Purple and
Purple / Black wires from the male connector to the Green, Green / Black, Purple and Purple / Black wires from the female
connector.
5. For vehicles that lose audio output when there is no load on the speaker outputs of the factory ampliîš¿er, PAC load resistors
will be required (PAC Part Number LR335 or LR475).
1. Locate the vehicle’s factory amplier and disconnect the 10-pin and 12-pin connectors.
2. Connect the APH-TY04 harnesses to the connectors that were disconnected in the previous step.
3. Connect the male connectors from the APH-TY04 to the ampliîš¿er.
4. Connect the longer loose wires from the APH-TY04, to your aftermarket ampliîš¿er outputs or passive crossovers, according
to the tables in this manual.
5. Insulate unused wires in the 10-pin and 12-pin connectors that plug into the factory ampliîš¿er side of the APH-TY04.
Installation Steps
Insulate any unused wires
Blue / BlackBlue
Red
Gree Redn /
Yellow / Red
1
610
7
Re Blackd /
Brown
Gree Whiten /
Yello Bluew /
Brow Blackn /
APH-TY04-HAR 10P A
6
1
10
7
Yello Bluew /
Yello
w / Red
Gree Redn /
Red
Blue
Gree Whiten /
Brow Blackn /
Re Blackd /
Blue / k Blac
Brown
APH-TY04-HAR 10P
B
1
Blue / Black Subwoofer 2 -
7
Blue Subwoofer 2 +
2
Red / Black Subwoofer 1 -
8
Red Subwoofer 1 +
3
Brown / Black Speaker 3 -
4
Brown Speaker 3 +
5
Green / White Speaker 1 -
9
Green / Red Speaker 1 +
6
Yellow / Blue Speaker 2 -
10
Yellow / Red Speaker 2 +
Speaker 2
Subwoofer 2
Subwoofer 1
Speaker 3
Speaker 1
Pin Number Wire Color Wires Description Label
APH-TY04 10-Pin Connector
Connect to aftermarket ampliîš¿er
output or passive crossover.
Speaker Connection Harness for Select
Toyota and Lexus Vehicles with Factory Ampliîš¿ers
Equipped with a 10-Pin and 12-Pin Connector
APH-TY04
C
Page 2
Copyright © 2019. All rights reserved. PAC is a Power Brand of AAMP Global.
PAC-audio.com
Rev: V1
Date: 010419
Whit Rede /
Gray / Red
White
Green
Purple
White / Blue
Gra Bluey /
Whit Blacke /
Gree Blackn /
Gray / Black
Gray
Purple / Black
1
7
8
12
APH-TY04-HAR 12P A
White e/ Blu
Gra Bluey /
Whit Blacke /
Gree Blackn /
1
7
8
12
Gray / k Blac
Gray
Purple k/ Blac
Whit Rede /
Gray / Red
White
Green
Purple
APH-TY04-HAR 12P
B
Wiring Overview (cont.)
APH-TY04 12-Pin Connector
Insulate any unused wires
1
White / Blue Speaker 4 -
8
White / Red Speaker 4 +
2
Gray / Blue Speaker 5 -
9
Gray / Red Speaker 5 +
3
White / Black Front Left -
10
White Front Left +
4
Gray / Black Front Right -
5
Gray Front Right +
6
Green / Black Rear Left -
11
Green Rear Left +
7
Purple / Black Rear Right -
12
Purple Rear Right +
Front Left Speaker
Front Right Speaker
Rear Left Speaker
Rear Right Speaker
Pin Number Wire Color Wires Description Label
Speaker 4
Speaker 5
Connect to aftermarket ampliîš¿er
output or passive crossover.


Produktspezifikationen

Marke: PAC
Kategorie: Nicht kategorisiert
Modell: APH-TY04

Brauchst du Hilfe?

Wenn Sie Hilfe mit PAC APH-TY04 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Nicht kategorisiert PAC

Bedienungsanleitung Nicht kategorisiert

Neueste Bedienungsanleitung für -Kategorien-