PAC APH-TY03 Bedienungsanleitung


Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für PAC APH-TY03 (1 Seiten) in der Kategorie Nicht kategorisiert. Dieser Bedienungsanleitung war für 3 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/1
Speaker Connection Harness for Select
For Select Toyota Vehicles with Factory Ampliîš¿ers
Equipped with a 20-Pin Connector
APH-TY03
C
Page 1
Copyright © 2019. All rights reserved. PAC is a Power Brand of AAMP Global.
PAC-audio.com
Rev: V1
Date: 010419
APH-TY03-HAR
1
11
12
20
121
2011
Whit Blacke /
Yellow
White
Yellow
Gray / BlackGray
Purple k / Blac
Gree Blackn /
Purple
Green
Black
Black
Orange k / Blac
Blue / Black
Orange
Blue
Brow Blackn /
Re Blackd /
Brown
Red
Whit Blacke /
Yellow
White
Yellow
Gray / kBlac Gray
Purple k/ Blac
Gree Blackn /
Purple
Green
Black
Black
Orange k/ Blac
Blue / kBlac
Orange
Blue
Re Blackd /
Brow Blackn /
Red
Brown
Introduction and Features
The APH-TY03 simpliîš¿es speaker wire connections when adding aftermarket ampliîš¿ers. Aftermarket ampliîš¿ers can
be easily added with no need to cut or modify a vehicle’s original wiring. Each pair of wires has been labeled with the
corresponding speaker name.
Wiring Overview
Installation Notes
1. It is always best to use a tone generator (PAC part number: TL-PTG2) to verify that the tables in this manual, and the labels
on the wires, match the wiring in your speciîš¿c vehicle.
2. The Gray 20-pin connector from the APH-TY03 must be connected to the factory ampliîš¿er when using a PAC AmpPRO
Interface.
3. Not all applicable vehicles will come equipped with a corresponding speaker for all of the wires populated in our harness. It is
important to understand which speakers are equipped in your vehicle.
4. If you are leaving any of the factory speakers connected to the factory ampliîš¿er, simply connect the speaker wires (color for
color) between the male and female connectors, for the speakers that will be powered by the factory ampliîš¿er. For example:
If you want the rear speakers to be powered by the factory ampliîš¿er, simply connect the Green, Green / Black, Purple and
Purple / Black wires from the male connector to the Green, Green / Black, Purple and Purple / Black wires from the female
connector.
5. For vehicles that lose audio output when there is no load on the speaker outputs of the factory ampliîš¿er, PAC load resistors
will be required (PAC Part Number LR335 or LR475).
1. Locate the vehicle’s factory amplier and disconnect the 20-pin connector.
2. Connect the APH-TY03 harness to the connector that was disconnected in the previous step.
3. Connect the male connector from the APH-TY03 to the ampliîš¿er.
4. Connect the longer loose wires from the APH-TY03, to your aftermarket ampliîš¿er or passive crossovers, according to the
tables in this manual.
5. Insulate unused wires in the 20-pin connector that plugs into the factory ampliîš¿er side of the APH-TY03.
Installation Steps
Connect to aftermarket
ampliîš¿er or passive
crossover
Insulate any unused wires
1 Yellow
12 Yellow
2
White / Black Speaker 1 -
13
White Speaker 1 +
3
Gray / Black Speaker 2 -
14
Gray Speaker 2 +
4
Green / Black Speaker 3 -
15
Green Speaker 3 +
5
Purple / Black Speaker 4 -
16
Purple Speaker 4 +
6
Black
7
Black
8
Blue/Black Speaker 5 -
17
Blue Speaker 5 +
9
Orange/Black Speaker 6 -
18
Orange Speaker 6 +
10
Red / Black Speaker 7 -
19
Red Speaker 7 +
11
Brown / Black Speaker 8 -
20
Brown Speaker 8 +
Speaker 8
Pass through (Ground)
Speaker 1
Speaker 2
Speaker 3
Speaker 4
Speaker 5
Speaker 6
Speaker 7
Pin Number Wire Color Wires Description Label
Pass through (Constant 12v)


Produktspezifikationen

Marke: PAC
Kategorie: Nicht kategorisiert
Modell: APH-TY03

Brauchst du Hilfe?

Wenn Sie Hilfe mit PAC APH-TY03 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Nicht kategorisiert PAC

Bedienungsanleitung Nicht kategorisiert

Neueste Bedienungsanleitung für -Kategorien-