PAC AP4-FD31 Bedienungsanleitung

PAC Nicht kategorisiert AP4-FD31

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für PAC AP4-FD31 (10 Seiten) in der Kategorie Nicht kategorisiert. Dieser Bedienungsanleitung war für 35 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF
Seite 1/10
© 2021 AAMP Global. All rights reserved. PAC is a Power Brand of AAMP Global.
PAC-audio.com
C
Page 1
Rev: 2
Date:020922
Advanced Ampliîš¿er Interface
for Select Ford Vehicles
AP4-FD31
The AP4-FD31 provides a 6-channel pre-amp output for use with aftermarket audio equipment. Using the digital
A2B audio data in conjunction with CAN data, the AP4-FD31 delivers a variable 5v RMS pre-amp output with fading,
balance, equalization, and level control capabilities. The module also retains audio from other vehicle features such
as factory navigation prompts, safety chimes, Bluetooth and voice activation. A data bus controlled remote ampliîš¿er
turn on wire is also provided by the AP4-FD31. The module also provides a variable 2-channel îš¿ber optic digital audio
output (TOSLINK).
Introduction and Features
Important Notes
1. This interface is only compatible in vehicles equipped with an A2B data bus controlled premium sound system. To verify
compatibility, look for a B&O badge on the door speakers or dash speakers.
2. The AP4 interface installs at the factory ampliîš¿er location. Included T-Harness installs behind radio to access factory
speaker wiring not available at factory ampliîš¿er.
3. The factory ampliîš¿er will be disconnected and will no longer power the vehicle speakers. An aftermarket ampliîš¿er must be
added to power the vehicle's speakers. For example, you cannot only add a subwoofer, as the factory speakers that were
connected to the factory ampliîš¿er will no longer function.
4. On most Ford models, some of the vehicle speakers will be connected to the radio module in addition to the external
ampliîš¿er. These speakers will also stop working when the factory ampliîš¿er is disconnected and will need to be powered by
an aftermarket ampliîš¿er. See Speaker Connections on Page 3 for vehicle speciîš¿c speaker information.
5. The chime volume and minimum volume levels are set to 50% by default. If this level is adequate, no additional adjustment
is required. Please refer to the Setup and Conîš¿guration section on page 9 for more details.
6. The level control knob must be connected in order to manually adjust the chime volume and minimum volume settings.
7. The remote output is rated at 2A of current. If more current is needed, an external relay must be used.
8. Channels 5 and 6 are non-fading outputs. The output level of channels 5 and 6 can be controlled using the supplied level
control knob.
9. No adjustments can be made manually using the programming button, or the factory SWC, when the module is connected
to a PC.
Module Layout
LED 1
Interface Connector 1
Expansion Port
TOSLINK Output
Programming Button
Feature Select
DIP switches
Front Output
Ch. 1(L) and 2(R)
Non-Fading Level Control
Knob Connection
USB Connection
Rear Output
Ch. 3(L) and 4(R)
SUB (Non-Fading)
Ch. 5 and 6
LED 2
DIP
1234
ON
Two Channel Mode Vehicle Select5v / 4v Preout Not Used
1 2 3 4
Set DIP switches to the ON position to activate the corresponding features.
Set DIP switches to the OFF position for any features that are not desired.
© 2021 AAMP Global. All rights reserved. PAC is a Power Brand of AAMP Global.
PAC-audio.com
C
Page 2
Rev: 2
Date:020922
Advanced Ampliîš¿er Interface
for Select Ford Vehicles
AP4-FD31
Installation
1. Access the factory ampliîš¿er (Audio Digital Sound Processing Module). Ampliîš¿er locations are listed starting on
Page 3.
2. Disconnect the 20-pin, 8-pin and A2B USB connectors from the ampliîš¿er. The ampliîš¿er can be removed or left in
the vehicle.
3. Plug the 20-pin, 8-pin and A2B USB cables into the matching connectors on the AmpPRO (AP4FD31HAR)
harness.
4. Before connecting the interface, set any feature DIP switches that apply to the install:
a. DIP switch 1 is used for two channel mode. In this mode, all outputs will be non-fading and all chimes are diverted
through channels 1 & 2 and TOSLINK.
b. Set DIP switch 2 on (down) to lower the RCA output voltage to 4v. Leave DIP switch 2 o󰀨 (up) to keep the RCA
output voltage at 5v. See troubleshooting section on Page 11 for more details.
c. DIP switch 3 is not used and should remain o󰀨 (up).
d. Set DIP switch 4 to on (down) position if installing interface in a Mach-E. For all other vehicle models, DIP switch
4 should be o󰀨 (up).
5. Connect the AmpPRO harness to the AmpPRO Interface Connector 1.
6. Connect the level control knob cable to the interface.
7. Connect the signal cables (RCA/TOSLINK) and remote input from the aftermarket ampliîš¿er.
NOTE! The aftermarket ampliîš¿er must have a very solid ground and the ampliîš¿er power/ground
connections should be made before connecting the RCA's or Remote Turn On to the AP4-FD31!
On aluminum framed vehicles, it is recommended to ground directly to the battery.
Wiring Connection Chart
Front
1/L 2/R 4/R 5 6
3/L
Remote Amp Turn On +
2A Max Output
Rear Sub
TOSLINK
20-pin
Amplifier
8-pin
Amplifier
A²B USB
Amplifier
To Vehicle Amplifier Harness
Speaker
Leads
1-10
Non-Fading
Level Control
Knob
To Aftermarket
Amplifier
AP4FD31HAR
© 2021 AAMP Global. All rights reserved. PAC is a Power Brand of AAMP Global.
PAC-audio.com
C
Page 3
Rev: 2
Date:020922
Advanced Ampliîš¿er Interface
for Select Ford Vehicles
AP4-FD31
Speaker Connections
If using the factory speaker wires to connect to the aftermarket ampliîš¿er, they will be located in two locations, at the 20-pin
plug at the Digital Sound Processing Module (Ampliîš¿er) and either a 32-pin or 24-pin plug at the Audio Control Module (Radio).
Adapter plugs are provided for all speaker wire connections.
Because the factory speaker wire pin locations, colors and plug style vary from model to model, reference the charts below
and use a tone generator for speaker locations and polarity. Please note that most vehicles will not follow the "standard"
speaker wire colors and polarity. For example the right front positive speaker lead may connect to the left rear negative
(GRN/BLK) lead on the adapter plug.
APH-FD22
24-PIN RADIO
SPEAKER HARNESS
APH-FD03
32-PIN RADIO
SPEAKER HARNESS
APHFD31HAR
20-PIN AMPLIFIER
SPEAKER HARNESS
TO RADIO TO RADIO
TO VEHICLE
HARNESS
SPEAKER
LEADS
SPEAKER
LEADS
SPEAKER
LEADS
TO VEHICLE
HARNESS
TO VEHICLE
AMPLIFIER
HARNESS
OR
For additional vehicle applications and the latest speaker wiring
information, visit the AP4-FD31 product page on PACaudio.com
20 Pin Plug at AMPLIFIER (DSP) (AP4FD31HAR)
LEADS PAC COLOR POSITION/POLARITY
Speaker 1 WHT LF KICK / +
Speaker 1 WHT/BLK LF KICK / –
Speaker 2 GRY RF KICK / +
Speaker 2 GRY/BLK RF KICK / –
Speaker 3 GRN LF DASH / +
Speaker 3 GRN/BLK LF DASH / –
Speaker 4 VIO RF DASH / +
Speaker 4 VIO/BLK RF DASH / –
Speaker 5 RED SUB2 / +
Speaker 5 RED/BLK SUB2 / –
Speaker 6 BLU SUB1 / +
Speaker 6 BLU/BLK SUB1 / –
Speaker 7 BRN
Speaker 7 BRN/BLK
32 Pin Plug at RADIO (ACM) (APH-FD03)
LEADS PAC COLOR POSITION/POLARITY
Speaker 1 WHT LR POD / +
Speaker 1 WHT/BLK LR POD / –
Speaker 2 GRY CENTER / +
Speaker 2 GRY/BLK CENTER / –
Speaker 3 GRN
Speaker 3 GRN/BLK
Speaker 4 VIO RR POD / +
Speaker 4 VIO/BLK RR POD / –
Speaker 5 ORG
Speaker 5 ORG/BLK
NOTES:
Ford Bronco (10 Speaker) 2021 | Ampliîš¿er Location: RH cargo area behind trim panel

Produktspezifikationen

Marke: PAC
Kategorie: Nicht kategorisiert
Modell: AP4-FD31

Brauchst du Hilfe?

Wenn Sie Hilfe mit PAC AP4-FD31 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten


Bedienungsanleitung Nicht kategorisiert PAC

PAC

PAC RP4-GM31 Bedienungsanleitung

6 September 2024
PAC

PAC NU-GM51 Bedienungsanleitung

6 September 2024
PAC

PAC NAV-1129 Bedienungsanleitung

6 September 2024
PAC

PAC LP7-2R Bedienungsanleitung

6 September 2024
PAC

PAC LP7-4 Bedienungsanleitung

6 September 2024
PAC

PAC GMK367B Bedienungsanleitung

6 September 2024
PAC

PAC CP1-FRD1 Bedienungsanleitung

6 September 2024
PAC

PAC C2A-CHY5 Bedienungsanleitung

6 September 2024
PAC

PAC NU-GM3 Bedienungsanleitung

6 September 2024
PAC

PAC CP1-TSL1 Bedienungsanleitung

6 September 2024

Bedienungsanleitung Nicht kategorisiert

Neueste Bedienungsanleitung für -Kategorien-

DAS Audio

DAS Audio AX-112-5 Bedienungsanleitung

16 Oktober 2024
Ferplast

Ferplast Ergocomfort Freetime Bedienungsanleitung

16 Oktober 2024
AEG

AEG MECK52 Bedienungsanleitung

16 Oktober 2024
Makita

Makita UR012G Bedienungsanleitung

16 Oktober 2024
Stihl

Stihl HT 70 Bedienungsanleitung

16 Oktober 2024
Ernesto

Ernesto H14270 Bedienungsanleitung

16 Oktober 2024
IFM

IFM AC901S Bedienungsanleitung

16 Oktober 2024
Nedis

Nedis RFPOM120FBK Bedienungsanleitung

16 Oktober 2024
AEG

AEG E9KLCS01 Bedienungsanleitung

16 Oktober 2024
ART

ART ProChannel II Bedienungsanleitung

16 Oktober 2024