Ozito PTP-425 Bedienungsanleitung

Ozito pomp PTP-425

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Ozito PTP-425 (8 Seiten) in der Kategorie pomp. Dieser Bedienungsanleitung war für 20 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/8
1
INSTRUCTION MANUAL
PTP-425
STANDARD EQUIPMENT
IN ORDER TO MAKE A CLAIM UNDER THIS
WARRANTY YOU MUST RETURN THE PRODUCT
TO YOUR NEAREST BUNNINGS WAREHOUSE WITH
YOUR BUNNINGS REGISTER RECEIPT. PRIOR TO
RETURNING YOUR PRODUCT FOR WARRANTY
PLEASE TELEPHONE OUR CUSTOMER SERVICE
HELPLINE:
Australia 1800 069 486
New Zealand 0508 069 486
1 YEAR WARRANTY
Your product is guaranteed for a period of 12 months from the
original date of purchase and is intended for DIY (Do It Yourself)
use only. If a product is defective it will be repaired in accordance
with the terms of this warranty. Warranty excludes consumable
parts, for example: o-rings, bearing, seals, gaskets and adaptors.
WARNING
The following actions will result in the warranty being void.
• If the tool has been operated on a supply voltage other
than that specied on the tool.
• If the tool shows signs of damage or defects caused
by or resulting from abuse, accidents or alterations.
• Failure to perform maintenance as set out within the
instruction manual.
• If the tool is disassembled or tampered with in any way.
• Professional, industrial or high frequency use.
WARRANTY
TO ENSURE A SPEEDY RESPONSE PLEASE
HAVE THE MODEL NUMBER AND DATE OF
PURCHASE AVAILABLE. A CUSTOMER SERVICE
REPRESENTATIVE WILL TAKE YOUR CALL
AND ANSWER ANY QUESTIONS YOU MAY
HAVE RELATING TO THE WARRANTY POLICY
OR PROCEDURE.
OZITO Australia/New Zealand (Head Ofce) 25 Fox Drive, Dandenong South, Victoria, Australia 3175
The benets provided under this warranty are in addition
to other rights and remedies which are available to you at law.
Our goods come with guarantees that cannot be excluded
at law. You are entitled to a replacement or refund for a major
failure and for compensation for any other reasonably foreseeable
loss or damage. You are also entitled to have the goods repaired
or replaced if the goods fail to be of acceptable quality and the
failure does not amount to a major failure.
Generally you will be responsible for all costs associated with
a claim under this warranty, however, where you have suffered
any additional direct loss as a result of a defective product you
may be able to claim such expenses by contacting our customer
service helpline above.
PETROL
TRANSFER
PUMP
79cc 4 STROKE
SPECIFICATIONS
Engine: 4 Stroke, air cooled
Engine Output: 1.30kW (1.7HP)
Fuel Type: Unleaded petrol
Fuel Tank Capacity: 1.6 litres
Displacement: 79cc
Max. Flow Rate: 4,000l/h
Max. Head: 9m
Max. Lift: 7m
Inlet/Outlet: 25mm (1”)
Weight: 14.3kg
Filter & Funnel
Fasteners & Adaptors
ozito.com.au
Tools
Petrol Transfer Pump
1220
ONLINE MANUAL
Scan this QR Code with your
mobile device to take you to
the online manual.
1. CONNECTING THE INLET
WARNING!: ENSURE THE ENGINE IS SHUT OFF AND
THE ON/OFF SWITCH IS IN THE OFF POSITION BEFORE
PERFORMING ANY OF THE FOLLOWING ASSEMBLY.
Connecting the Suction Inlet
1. Placethelter
assembly into the
intake end of a
suction hose (not
supplied) and
secure with a hose
clamp tightly.
2. Insert a hose
adaptor and a
O-ring into one
of the collars and
fasten to the outlet
side of the suction
hose using a hose
clamp.
3. Screw the hose adaptor
assembly tightly onto the
pumps inlet in a clockwise
direction to secure in place.
Note: Teontape(notsupplied)
is recommended on threads to
ensure a water tight seal and
prevent any leakage. DO NOT
use adhesives in replace of
Teontape.
The inlet allows for a 25.4mm (1”) supply line to be connected
and is capable of a maximum suction height (lift) of 7m.
WARNING!: AVOID POSITIONING THE INLET PIPE
HIGHER THAN THE PUMP, AS THIS WOULD DELAY THE
ESCAPE OF AIR BUBBLES FROM THE INLET PIPE.
WARNING!: THE INPUT HOSE OR PIPE SHOULD BE
LOW ENOUGH IN THE WATER TO ENSURE THAT IF THE
WATER LEVEL FALLS, THE PUMP WILL NOT RUN DRY.
ENSURE THAT THIS IS CHECKED WHEN IN OPERATION.
15. Spark Plug Wrench
16. Filter
17. Spanner
18. Screwdriver
19. Funnel
20. Hose Clamp (x3)
21. Collar (x2)
22. O-ring (x2)
23. Hose Adaptor (x2)
7. Priming Cap
8. On/Off Switch
9. Carry Handle
10. Discharge Outlet
11. Suction Inlet
12. Fuel Lever
13. Drain Screw
14. Oil Fill / Dipstick
KNOW YOUR PRODUCT SETUP & PREPARATION
PETROL TRANSFER PUMP
ACCESSORIES
1
12
4
2
13
8
3
7
15
9
14
16 17 18 19 20 21 22 23
10
6
11
1. Fuel Cap
2. Choke Lever
3. Air Filter Cover
4. Fuel Tank
5. Throttle Lever
6. Recoil Starter
IMPORTANT: TO USE THE PUMP IN PERMANENT
INSTALLATIONS WITH RIGID PIPES, ALWAYS INSTALL A
FILTER SUITABLE FOR YOUR APPLICATION TO PROTECT THE
PUMP FROM SAND, DIRT ETC.
5
3.
INSTALLATION
Connecting the Discharge Outlet
1. Insert a hose
adaptor and an
O-ring into one of
the collars.
2. Screw the hose adaptor and
collar tightly onto the pump
outlet in a clockwise direction
to secure in place.
Note: Teontape(notsupplied)
is recommended on threads to
ensure a water tight seal and
prevent any leakage. DO NOT
use adhesives in replace of
Teontape.
The outlet allows for a 25.4mm (1”) pipe to be connected and is
capable of a maximum head of 9m.
2. CONNECTING THE OUTLET
IMPORTANT: TO USE THE PUMP IN PERMANENT
INSTALLATIONS WITH RIGID PIPES, INSTALL A NON-RETURN
VALVE TO AVOID THE FLUID BEING RE-CIRCULATED ONCE
THE PUMP HAS STOPPED.
WARNING!: ALL CONNECTIONS MUST BE AIR TIGHT,
FAILURE TO DO SO MAY RESULT IN AN AIR LEAK
WHICH CAN PREVENT THE PUMP FROM PRIMING. 1. Ensure the pump is mounted to a rigid base or ground.
9m
7m
MAXIMUM DELIVERY HEIGHT
WATER LEVEL
WARNING!: ALWAYS CARRY OR LIFT THE PUMP BY THE
CARRY HANDLE TO AVOID DAMAGING THE UNIT.
WARNING!: THIS PRODUCT IS INTENDED FOR PUMPING
WATER IN A HOME DOMESTIC APPLICATION. DO NOT
USE IT FOR CORROSIVE, ABRASIVE, EXPLOSIVE OR
DANGEROUS LIQUIDS.
2. Ensure the distance from the surface of the water to the
pump inlet does not exceed 7m.
3. Ensure the distance from the pump to the highest point that
you wish to deliver the water does not exceed 9 metres.
Before starting, perform a few simple checks:
WARNING!: ENSURE THE OUTLET FOR THIS
PUMP, INCLUDING ANY HOSES OR PIPES ARE NOT
RESTRICTED OR OBSTRUCTED IN ANY WAY. TAPS,
VALVES AND ANY TYPE OF TRIGGER NOZZLE MUST
NEVER BE USED WITH THIS PUMP. FAILURE TO
FOLLOW THESE INSTRUCTIONS MAY RESULT IN PUMP
FAILURE OR SERIOUS INJURY.


Produktspezifikationen

Marke: Ozito
Kategorie: pomp
Modell: PTP-425

Brauchst du Hilfe?

Wenn Sie Hilfe mit Ozito PTP-425 benĂśtigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung pomp Ozito

Bedienungsanleitung pomp

Neueste Bedienungsanleitung fĂźr -Kategorien-