Ozito MWR-090 Bedienungsanleitung
Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Ozito MWR-090 (8 Seiten) in der Kategorie Schweißer. Dieser Bedienungsanleitung war für 18 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet
Seite 1/8
GASLESS
MIG WELDER
90 Amp
INSTRUCTION MANUAL
SPECIFICATIONS
Input Voltage: 240V ~ 50Hz
Welding Current: 65 - 90Amp
Welding Wire Size: 0.8-0.9mm Flux-Cored Wire
Duty Cycle: 25%@90A
Insulation Type: Earthed Appliance (Class I)
Wire Spool Weight: 0.2kg to 5kg
Weight (tool only): 16.7kg
MWR-090
WHAT’S IN THE BOX
MIG Welder
Wire Feed Roller
Mig Wire
Welding Mask
Chipping Hammer /
Wire Brush
ozito.com.au
IN ORDER TO MAKE A CLAIM UNDER THIS
WARRANTY YOU MUST RETURN THE PRODUCT
TO YOUR NEAREST BUNNINGS WAREHOUSE WITH
YOUR BUNNINGS REGISTER RECEIPT. PRIOR TO
RETURNING YOUR PRODUCT FOR WARRANTY
PLEASE TELEPHONE OUR CUSTOMER SERVICE
HELPLINE:
Australia 1800 069 486
New Zealand 0508 069 486
3 YEAR REPLACEMENT WARRANTY
Your product is guaranteed for a period of 36 months from
the original date of purchase. If a product is defective it will
be replaced in accordance with the terms of this warranty.
Warranty excludes consumable parts, for example: Welding tips,
torch nozzles, flexible inner tube, welding wire, wire feed rollers,
welding lenses, wire brushes and chipping hammer.
WARNING
The following actions will result in the warranty being void.
• If the tool has been operated on a supply voltage other
than that specified on the tool.
• If the tool shows signs of damage or defects caused
by or resulting from abuse, accidents or alterations.
• Failure to perform maintenance as set out within the
instruction manual.
• If the tool is disassembled or tampered with in any way.
• Professional, industrial or high frequency use.
WARRANTY
TO ENSURE A SPEEDY RESPONSE PLEASE
HAVE THE MODEL NUMBER AND DATE OF
PURCHASE AVAILABLE. A CUSTOMER SERVICE
REPRESENTATIVE WILL TAKE YOUR CALL
AND ANSWER ANY QUESTIONS YOU MAY
HAVE RELATING TO THE WARRANTY POLICY
OR PROCEDURE.
OZITO Australia/New Zealand (Head Office) 1-23 Letcon Drive, Bangholme, Victoria, Australia 3175.
The benefits provided under this warranty are in addition
to other rights and remedies which are available to you at law.
Our goods come with guarantees that cannot be excluded
at law. You are entitled to a replacement or refund for a major
failure and for compensation for any other reasonably foreseeable
loss or damage. You are also entitled to have the goods repaired
or replaced if the goods fail to be of acceptable quality and the
failure does not amount to a major failure.
Generally you will be responsible for all costs associated with
a claim under this warranty, however, where you have suffered
any additional direct loss as a result of a defective product you
may be able to claim such expenses by contacting our customer
service helpline above.
1014
MIN
MAX
MIN
MAX
ONLINE MANUAL
Scan this QR Code with your
mobile device to take you to
the online manual.
The MIG welder is supplied with a 0.2kg coil of 0.8mm gasless
welding wire. Welding wire up to 5kg can be tted to this
welder.
MIG WELDER
ACCESSORIES
1 Internal Cooling Fan
2 Side Cover Release Lever
3 Side Cover
4 On/Off Switch
5 Overload Protection LED
6 Voltage Control Switch
7 Carry Handle
8 MIG Torch
9 Torch Tip
10 Earth Clamp
11 Shroud
12 Wire Feed Speed & Current
Adjustment Knob
13 Power Cord
14 Welding Mask
15 Chipping Hammer / Wire
Brush
16 Wire Feed Roller 0.8-0.9mm
(Fitted)
17 Mig Wire
KNOW YOUR PRODUCT
1.
FITTING THE WELDING WIRE COIL
SETUP & PREPARATION
1 2 3 4 5 6 7
14 15 16
WARNING: ENSURE THE TOOL IS SWITCHED OFF AND
DISCONNECTED FROM THE POWER SUPPLY BEFORE
PERFORMING ANY OF THE FOLLOWING STEPS.
2 Remove the retaining nut
by rotating anti-clockwise
and remove the spring
and drive washer.
4 Align the spring and drive
washer lug with the slot in
the drive shaft and secure
with the retaining nut, but
do not over tighten.
1 Open the side cover
by lifting the side
cover release lever.
3 Slide the welding
wire coil onto the
shaft.
Note: Over tightening of the retaining nut will restrict the wire
feed rate and can cause damage to the wire feed motor or
irregular welding.
8 9 10 12 1311
17
2. WIRE DRIVE ROLLER SIZE 3. FEEDING THE WELDING WIRE
OPERATION
2 Pull the pressure screw
arm down and raise the
pressure arm.
1 With the pressure arm
raised away from the drive
roller, feed the welding
wire into the inlet guide
and between the wire
drive rollers.
4 Lift the wire drive roller off
the shaft and inspect it to
conrm the wire groove
size stamped on either
face. Always ensure the
wire drive roller size you
require is facing outward
when assembled.
3 Push the pressure arm
downward and raise the
pressure arm screw.
There are two different size rollers grooves machined into the
outer surface of the wire drive roller for a gasless MIG welder.
Flux-cored welding wire (0.8 - 0.9mm) is required to operate
this welder.
1 Release the pressure
of the pressure roller
by loosening the
adjustable pressure
screw anti-clockwise. Ensure the welding wire is free from any kinks and bends by
removing any damaged wire. When cutting the wire, ensure it
is not cut at an angle. It is recommended you lightly le the at
end of the wire prior to feeding.
3 Remove the wire
drive roller bracket by
rotating anti-clockwise
and then pulling
outwards.
2 Pass the wire through
the conduit liner,
ensuring the wire
is positioned in the
groove of the drive
roller.
4 Tighten the adjustable
pressure screw so
that the screw is
about half way down.
5 Secure the wire drive
roller by tting the
drive roller bracket
and fasten by rotation
clockwise.
Note: Do not over tighten the drive roller bracket as this could
damage the MIG welder.
CAUTION: IT IS CRITICAL THAT YOU CHOOSE THE
CORRECT WIRE DRIVE ROLLER SIZE.
WARNING: ENSURE THAT YOU DO NOT MAKE CONTACT
WITH THE EARTH CLAMP AT ANY STAGE WHEN
FEEDING THE WELDING WIRE THROUGH THE MIG
TORCH. THE ELECTRODE WIRE WILL BE AT WELDING
VOLTAGE WHILST IT IS BEING FED THROUGH THE
WELDER. KEEP THE MIG TORCH AWAY FROM YOUR
EYES AND FACE.
WARNING: THE POWER SUPPLY FOR THIS PRODUCT SHOULD
BE PROTECTED BY A RESIDUAL CURRENT DEVICE (RATED AT
30MA OR LESS). A RESIDUAL CURRENT DEVICE REDUCES THE
RISK OF ELECTRIC SHOCK.
Produktspezifikationen
| Marke: | Ozito |
| Kategorie: | Schweißer |
| Modell: | MWR-090 |
Brauchst du Hilfe?
Wenn Sie Hilfe mit Ozito MWR-090 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten
Bedienungsanleitung Schweißer Ozito
26 Juni 2024
7 Februar 2024
29 Januar 2024
6 Januar 2024
29 Oktober 2022
Bedienungsanleitung Schweißer
- Schweißer Parkside
- Schweißer Taurus
- Schweißer Topcraft
- Schweißer Hyundai
- Schweißer Stanley
- Schweißer Güde
- Schweißer Scheppach
- Schweißer Weller
- Schweißer Silverline
- Schweißer Herkules
- Schweißer ROWI
- Schweißer GYS
- Schweißer Telwin
- Schweißer SainSmart
- Schweißer Bavaria
- Schweißer Kemppi
- Schweißer Lincoln Electric
- Schweißer Mag-Torch
- Schweißer Amico Power
- Schweißer THUN
- Schweißer Hyper Welding
Neueste Bedienungsanleitung für -Kategorien-
26 Juni 2024
26 Juni 2024
26 Juni 2024
26 Juni 2024
26 Juni 2024
26 Juni 2024
26 Juni 2024
25 Juni 2024
9 Juni 2024
9 Juni 2024