Oricom WAKE'N' SHAKE WNS10 Bedienungsanleitung

Oricom Nicht kategorisiert WAKE'N' SHAKE WNS10

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Oricom WAKE'N' SHAKE WNS10 (1 Seiten) in der Kategorie Nicht kategorisiert. Dieser Bedienungsanleitung war für 7 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF

Seite 1/1

1 32 4

TO SELECT THE ALARM MODE

At normal time display mode, press one at a time to activate the alarm(s), AL SET / SELECT

the corresponding alarm indicator(s) on the right side of the time display will be on:

only sound

alarm is

activated

only shaker

alarm is

activated

only strobe

light

alarm is

activated

both sound and

vibration alarm are

activated

both strobe light

and

sound alarm

are

activated

Press AL SET / SELECT once more to turn off all the alarms, all alarm

indicators disappear.

TO STOP AND RESET THE ALARM TO COME ON THE NEXT DAY

When alarm is sounding, the corresponding alarm indicator ﬂashes. Press AL SET /

SELECT once to stop the alarm and reset it to come on the following day. After that, the

corresponding alarm indicator stays on the display.

TO USE SNOOZE

When the alarm is sounding, press once, the alarm will be stopped temporarily

and the corresponding alarm indicator will keep ﬂashing. Alarm will come on again after

the set snooze duration is over.

TO USE BACKLIGHT

Press once to activate the backlight 5 seconds.

TO USE FLASHLIGHT

Press and hold to activate the ﬂashlight. Press and hold to de-activate

the ﬂashlight.

TO USE COUNTDOWN TIMER (HOUR-MINUTE TIMER)

1. At normal time display, press once, display change to timer mode, SET / TIMER

and ▲ will appear with “0:00” ﬂash.

2. Press ▼ to adjust countdown timer in hours, press to adjust countdown time in minutes.▲

3. Press START / STOP once to start countdown in minutes, then “:” and “ ” ﬂash.▼

4. During counting down, press START / STOP to pause counting down and the whole

display ﬂashes. Press and hold START / STOP to stop or reset the counting down timer.

5. Press START / STOP again for continuous counting down. “:” and “ ” ﬂash again.▼

6. When the timer reaches “ ” (00 seconds), the clock vibrates / sounds / ﬂashes with 0:00

LED and it starts to count up to show the overrun time. Press START / STOP once to

stop the timer alarm.

7. Press START / STOP again, the display shows last count down set time and ﬂashes.

Repeat Step 2-5 to set and use countdown timer.

Remark: When timer is active and counting down or up, press the can SET / TIMER

return to the time display. The timer icon will ﬂash on the normal time display.

Press SET /

TIMER

once to

enter timer

mode.

Press or ▲

▼ to set

countdown

time

Press

START /

STOP once

to count

down

Press

START /

STOP to

pause

count down

When countdown timer reaches

0:00 (0 seconds), the clock

vibrates/ sounds/ ﬂashes and

starts to count up to show the

elapsed time. Press START /

STOP once to stop the timer alarm.

TO USE COUNT-UP TIMER (MAX. 23HR 59MIN.)

1. At normal time display, press once, display changes to timer mode and SET / TIMER

ﬂashes. Press and hold START / STOP to reset timer value to “0:00”.

2. Press START / STOP once to start count up timer. “:” and “ ” ﬂash.▲

3. During counting, press START / STOP once to pause counting up and whole display

ﬂashes. Press and hold START / STOP to stop or reset the counting up timer.

4. Press START / STOP once again to continue counting up.

When timer value is reset to (Press and hold 0:00 START / STOP), press

START / STOP once to start count-up.

Remark: When timer is active and counting down or up, press the button. SET / TIMER

It will return to the time display. The timer icon will ﬂash on the normal time display.

TEST MODE

Press and hold / button, strobe light ﬂashing, shaker vibrating and buzzer sounding ▲TEST

for 5 seconds and then stops.

BATTERY INSTALLATION

Your clock requires 1 x AAA and 2 x AA alkaline batteries (included) to operate.

1. Place your unit face down on a ﬂat surface.

2. Press the latch and remove the battery cover at the back of your unit.

3. Insert 1 x AAA and 2 x AA new alkaline batteries into the battery compartment by

observing the correct “+” and “-” polarity.

4. Replace the battery cover.

AUTO KEY-LOCK

Auto key-lock applies to all other buttons (if no buttons are pressed after 1 minute). Press

and hold DOWN button to release the key lock, two soft and short beep tones will

be heard.

TO SET TIME AND THE SNOOZE DURATION

1. Press and hold , the hour digits “ ” ﬂash. Press or to set the time in SET / TIMER 0 ▲ ▼

hours (hold or to advance rapidly).▲ ▼

2. Press SET / TIMER again, the minute digits “ ” ﬂash. Press or 00 ▲ ▼ to set the time in

minutes (hold or to advance rapidly).▲ ▼

3. Press SET / TIMER again, the display shows “ ” and ﬂashes. Press or to 24Hr ▲ ▼

select “ ” or “ ” time format. The icon appears to indicate the morning time 12Hr 24Hr AM

and PM icon to indicate the afternoon time.

4. Press SET / TIMER again, the display shows “ ” and ﬂashes. Press or to select 05 ▲ ▼

your snooze time from 5 to 60 minutes.

5. Press SET / TIMER to exit the setting mode, (or if no key has been pressed for approx.

10 seconds).

THE ALARM (default at 6:00 AM)

1. Press and hold , the appears and the alarm’s hour digits’ ﬂash. AL SET / SELECT AL

Press ▲ or ▼ to set the alarm in hours (hold ▲ or ▼ to advance rapidly).

2. Press AL SET / SELECT once again, the alarm’s minute digits’ ﬂash. Press or to ▲ ▼

set the alarm in minutes (hold or to advance rapidly).▲ ▼

3. Press AL SET / SELECT again, and “ ” ﬂash (vibration at HI level), press or HI ▲

▼ to select “LO” (vibration at Low level) if needed.

4. Press AL SET / SELECT again, and “ ” ﬂash (Sound at HIGH level), press or HI ▲

▼ to select “LO” (Sound at Low level) if need.

5. Press AL SET/SELECT once again or no button around 10 seconds to exit the alarm

setting mode. Admist alarm setting, press once to exit and return to SET / TIMER

normal time display mode.

LOW BATTERY ALERT

When the battery level becomes low, an low battery icon will appear on the upper

middle of the LCD. Replace batteries with new alkaline batteries.

Remark: Frequent use of the vibration alarm will quickly shorten the battery life.

TROUBLE SHOOTING

If your clock displays irrelevant time or does not function properly, which may be caused

by electro-static discharge or other interference, open the battery cover, take out the

batteries and reinstall them by observing the correct +/- polarity. Your clock will be reset to

default settings and you need to set it again. Low battery level will decrease the vibration

and the alarm sound. Once this happens, replace batteries with new ones.

CARE OF YOUR PRODUCT

1. Place your clock on a stable surface, away from sources of direct sunlight or excessive

heat or moisture.

2. Protect your furniture when placing your units on a natural wood and lacquered ﬁnish by

using a cloth or protective material between it and the furniture.

3. Clean your unit with a soft cloth moistened only with mild soap and water. Stronger

agents such as Benzene, thinner or similar materials can damage the surface of the

unit. Make sure the unit is unplugged before cleaning.

4. If the unit is not to be used for a prolonged period, such as a month or longer, remove

the batteries to prevent possible corrosion. Should the battery compartment become

corroded or dirty, clean the compartment thoroughly and replace the batteries.

SPECIFICATIONS

Alarm duration : 1 minute

Snooze duration Adjustable : 5 to 60 minutes

Default settings

Time format 24 hour

Time 0:00

Alarm 6:00

Shaker alarm level Hi

Snooze duration 05 (5 minutes)

Count-up / countdown time 23 hours 59 minutes

Audible alarm : up to 75 dB at 1m

Express Warranty (Australia)

This Express Warranty is provided by Oricom International Pty Ltd ABN 46 086 116 369,

Unit 1, 4 Sovereign Place, South Windsor NSW 2756, herein after referred to as “Oricom”.

Oricom products come with guarantees that cannot be excluded under the Australian

Consumer Law. You are entitled to a replacement or refund for a major failure and

compensation for any other reasonably foreseeable loss or damage. You are also entitled

to have the goods repaired or replaced if the goods fail to be of acceptable quality and the

failure does not amount to a major failure.

Oricom warrants that the product is free from defects in materials or workmanship during

the Express Warranty Period. This Express Warranty does not extend to any product from

which the serial number has been removed or was purchased outside of Australia.

Nothing in this Express Warranty excludes, restricts or modiﬁes any condition, warranty,

guarantee, implied term, right or remedy pursuant to the Australian Consumer Law

and which may not be so excluded, restricted or modiﬁed. For such conditions, terms,

guarantees and warranties that cannot be excluded, restricted or modiﬁed, Oricom limits

the remedies available to extent permitted in the relevant legislation.

The Express Warranty Period will be 2 years from the date of purchase of the product

evidenced by your dated sales receipt. You are required to provide proof of purchase as a

condition of receiving Express Warranty services.

You are entitled to a replacement product or repair of the product at our discretion

according to the terms and conditions of this document if your product is found to be

faulty within the Express Warranty Period. This Express Warranty extends to the original

purchaser only and is not transferable.

Products distributed by Oricom are manufactured using new materials or new and used

materials equivalent to new in performance and reliability. Spare parts may be new or equivalent

to new. Spare parts are warranted to be free from defects in material or workmanship for thirty

(30) days or for the remainder of the Express Warranty Period of the Oricom branded product

in which they are installed, whichever is longer. During the Express Warranty Period, Oricom

will where possible repair and if not replace the faulty product or part thereof. All component

parts removed under this Express Warranty become the property of Oricom. In the unlikely

event that your Oricom product has a recurring failure, Oricom may always, subject to the

Competition and Consumer Act 2010, at its discretion, elect to provide you with a replacement

product of its choosing that is at least equivalent to your product in performance.

No change to the conditions of this Express Warranty is valid unless it is made in writing

and signed by an authorised representative of Oricom.

Oricom will not be liable under this Express Warranty, and to the extent permitted by law

will not be liable for any defect, loss, damage or injury arising out of or in connection with a:

1. Failure by you to adhere to the warnings and follow the instructions set out in this user

guide for the proper installation and use of the product;

2. Wilful misconduct or deliberate misuse by you of the product;

3. Any external cause beyond our control, including but not limited to power failure,

lightning or over voltage; or

4. Modiﬁcation to the product or services carried out on the product by anyone other than

Oricom or Oricom’s authorised service provider.

How to make a claim under your Express Warranty in Australia

Oricom has a simple warranty process for you to follow:

• Please call or email our Customer Support Team, 1300 889 785 or support@ oricom.com.au.

• A Customer Support Team member will verify after troubleshooting with you if your product

qualiﬁes under warranty. If so, they will give you a Product Return Authorisation number.

• We will then email or fax a Return Authorisation form and a Repair Notice (if necessary),

together with instructions on how to return the goods for warranty service.

Please note that if a Customer Support Team member advises that your product does

not qualify for return, this warranty does not apply to your product. Products that are

authorised to be returned to Oricom in Australia must include all of the following:

• A completed Return Authorisation form

• A copy of your Proof of Purchase (please keep your original copy)

• The faulty product, including all accessories.

Send the approved returns to:

Oricom International Pty Ltd

Locked Bag 658

South Windsor NSW 2756 Australia

Please note that this Express Warranty excludes expenses incurred by you in returning any

faulty product to us. You must arrange and pay any expenses incurred (including postage,

delivery, freight, transportation or insurance of the product) to return the faulty product

to us, however, we will arrange delivery of the repaired or replaced faulty product to you.

Important Information

Repair Notice

Please be aware that the repair of your goods may result in the loss of any usergenerated

data (such as stored telephone numbers, text messages and contact information). Please

ensure that you have made a copy of any data saved on your goods before sending

for repair. Please also be aware that goods presented for repair may be replaced by

refurbished goods or parts of the same type rather than being repaired.

ORICOM CUSTOMER SUPPORT

Oricom have a trained and dedicated team of Customer Support Represent-

atives, each with the knowledge and resources to assist in answering your questions

quickly and efficiently.

Oricom Support - Australia

For all product enquiries, troubleshooting or to discuss the range of Oricom products, feel

free to contact Oricom or visit our website for answers to frequently asked questions.

1300 889 785

Monday - Friday 8am – 6pm AEST

Email: support@oricom.com.au

www.oricom.com.au

Oricom Support - New Zealand

0800 674 266

Monday - Friday 10am - 8pm NZST

Email: support@oricom.co.nz

www.oricom.co.nz

Ref: 18102018

WNS10 USER GUIDE

KEEP THIS USER GUIDE FOR FUTURE REFERENCE

Always retain your proof of purchase in case of warranty service.

AUSTRALIA: www.oricom.com.au

Produktspezifikationen

Marke:	Oricom
Kategorie:	Nicht kategorisiert
Modell:	WAKE'N' SHAKE WNS10

Brauchst du Hilfe?

Wenn Sie Hilfe mit Oricom WAKE'N' SHAKE WNS10 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten

Ihren Namen*

Deine E-Mail*

Schreiben Sie hier Ihre Frage

Bedienungsanleitung Nicht kategorisiert Oricom

Oricom Eclipse OBHSSOO Bedienungsanleitung

19 August 2024

Oricom TP4 Bedienungsanleitung

17 August 2024

Oricom PRO610 Bedienungsanleitung

15 August 2024

Oricom WAKE'N' SHAKE WNS10 Bedienungsanleitung

13 August 2024

Oricom VISO10 Bedienungsanleitung

12 August 2024

Oricom OBHAD200 Bedienungsanleitung

12 August 2024

Oricom CARE820 Bedienungsanleitung

9 August 2024

Oricom CARE80 Bedienungsanleitung

8 August 2024

Oricom TP100 Bedienungsanleitung

8 August 2024

Oricom VAC500 Bedienungsanleitung

7 August 2024

Bedienungsanleitung Nicht kategorisiert

Neueste Bedienungsanleitung für -Kategorien-

DAS Audio AX-112-5 Bedienungsanleitung

16 Oktober 2024

Ferplast Ergocomfort Freetime Bedienungsanleitung

16 Oktober 2024

AEG MECK52 Bedienungsanleitung

16 Oktober 2024

Makita UR012G Bedienungsanleitung

16 Oktober 2024

Stihl HT 70 Bedienungsanleitung

16 Oktober 2024

Ernesto H14270 Bedienungsanleitung

16 Oktober 2024

IFM AC901S Bedienungsanleitung

16 Oktober 2024

Nedis RFPOM120FBK Bedienungsanleitung

16 Oktober 2024

AEG E9KLCS01 Bedienungsanleitung

16 Oktober 2024

ART ProChannel II Bedienungsanleitung

16 Oktober 2024