NUVO Bridgeview 60/1703 Bedienungsanleitung
Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für NUVO Bridgeview 60/1703 (2 Seiten) in der Kategorie Lamp. Dieser Bedienungsanleitung war für 6 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet
Seite 1/2
ASSEMBLY INSTRUCTION
SKU#60/1703
NOTE: Please consult a qualified electrician if you are not certain of installation or servicing.
CAUTION: Before starting installation or servicing, disconnect power by turning off the circuit breaker or by
removing the fuse at the fuse box.
1. Carefully unpack the fixture, lay out all parts on a clean surface.
2. Fasten the Mounting Strap to Outlet Box using the provided Outlet Box Screws.
3. Put Thread Rod through Cover A, Junction Box and Cover B, and tighten the Finial onto the Thread Rod.
Hang the Loops B of the Rods to Hooks as shown.
4. Using two pliers, twist open links at the two ends of the Chain. Hook one link to the Loop and the other link
to the Screw Collar Loop. Close the links. Place a piece of cloth between the pliers jaws and the chain links
to prevent scratching the link finish.
5. Weave the fixture wires up through the Loop, through the Chain, through the Ring, through the Canopy,
through the Screw Collar Loop and through the Nipple on the Mounting Strap.
6. Connect the wire with writing on it from the fixture to the black wire (live wire) from the supply circuit.
Connect the wire without writing on it (with raised ribs) from the fixture to the white wire (neutral wire)
from the supply circuit. Cover the connections using provided wire connectors. Tie ground wires from xture
and from Outlet Box to the Ground Screw on the Mounting Strap. Position wires back inside Outlet Box.
7. Place the Canopy over the Nipple all the way to the Ceiling and tighten the Ring onto the Screw Collar Loop
until the Canopy is held firmly against the ceiling.
8. Unscrew Socket Rings from Sockets. Place Shades over Sockets, reattach Socket Rings to Sockets to secure
the S es. Install
Turn on pow
had the Bulbs. (Not included).
9. er.
A Satco Product
INSTRUCCIÓN DE ASAMBLEA
SKU#60/1703
NOTE: Por favor, Consulte con un electricista cafificado en caso de que esté seguro de la instalación.
o quitar
instalación, disponer todas las piezas sobre una superficie lÃmpia.
ete el Embellecedor en la
4. rlo al lazo y al tuerca decorativa.
5. os cable del aparato desde abajohacia arriba a los enlaces de lozo, la cadena, el nillo, el dosel, pasando el lazo
6. gro desde el circuito del suministo. Conectar el cable
7. lar roscado
8. ntallas sobre los Zócalos, reacoplar los Aros del Zócalo
9.
INSTRUCTIONS DE MONTAGE
REMARQUE : Si vous avez des incertitu allation, demandez de l'aide à un électricien
TION : Avant de commencer l'installation, déconnectez l'alimentation électrique avec le disjoncteur
îtier de prise de courant.
ez le
4. ns à la Boucle et
5. ouvercle, dans la Boucle de
6. crite sur le fil noir (fil sous tension) du circuit d'alimentation.
7. Couvercle sur l'Embout jusqu'au niveau du Plafond, et fixez l'Anneau sur la Boucle de collier à vis jusqu'à ce
8. bat-jours sur les Douilles, et remettez en placez les Anneaux de
9. A llumez l'électricité.
CAUCIÓN: Antes de comenzar la instalación, cortar la electricidad mediante apagar el cortacircuitos
el fusible desde la caja de fusible.
1. Desempaquetar cuidadosamente la
2. Abroche la correa de montaje a la caja de salida usando los dos tornillos de la caja de salida.
3. Ponga la Vara Roscada a través de a Cubierta A, Caja de Ensambladura y Cover B, y apri
Vara Roscada. Cuelgue los Lazos B de las Varas a los Ganchos como está mostrado.
Usando dos alicates, torcer y abrir un enlace en el extremo de la cadena. Engancha
Colocar un pendazo de tela entre las mandibulas de los alicates y el enlace de la cadena para prevenir la rascadura del
enlace.
Tramar l
del collar roscado y el niple en la correa de montura.
Conectar el cable mediante escribirlo desde el aparato al cable ne
sin escribirlo(con la nervadura levantada)desde el aparato al cable blanco desde el circuito del suministro. Cubrir la
conexión usando el conector del cable provisto con el aparato. Atar el cable de tierra desde la caja de salida y desde el
aparato al tornillo del cable de tierra el la travesano. Posicione los cables negros dentro de la caja de salida.
Colocar el dosel completamente a través del niple más corto a la cúpula y ajustar el anillo al lazo del col
hasta que el dosel quede firmemente sujetada contra la cúpula.
Desatornillar los Aros del Zócalo de los Zócalos. Colocar las Pa
en los Zócalos para fijar las Pantallas. Instalar las bombillas. (No incluÃdas).
Activar la electricidad.
SKU#60/1703
des quant à l'inst
qualifié.
ATTEN
ou en retirant le fusible du disjoncteur. Calfeutrer la surface de montage au sommet et sur les côtés.
1. Déballez soigneusement le luminaire et placez toutes les pièces sur une surface propre.
2. Fixez la Bande de montage sur le Boîtier de prise de courant à l'aide de deux Vis pour bo
3. Faites passer le Montant fileté dans le Capot A, dans le Boîtier de raccordement et dans le Capot B, puis serr
Faîteau sur le Montant fileté. Accrochez les Boucles B des Montants sur les Crochets ainsi qu’illustré.
A l'aide de deux pinces, ouvrez les maillons aux deux extrémités de la Chaîne. Accrochez l'un des maillo
les autres maillons à la Boucle de collier de vis. Refermez les maillons. Placez un morceau de tissu entre les mâchoires
des pinces et les maillons de la chaîne afin d'éviter d'endommager la finition des maillons.
Faites passer les fils du luminaire dans la Boucle, dans la Chaîne, dans l'Anneau, dans le C
collier de vis et dans le Faîteau sur la Bande de montage.
Connectez le fil du luminaire qui comporte une mention é
Connectez le fil sans mention écrite (avec les cannelures) du luminaire sur le fil blanc (fil neutre) du circuit
d'alimentation. Couvrez les connexions à l'aide des connecteurs de fils fournis. Attachez les fils de terre du luminaire et
du Coffret de prise de courant sur la Vis de terre sur la Bande de montage. Faites entrer les fils dans le Coffret de prise de
courant.
Placez le
que le Couvercle soit fermement fixé contre le plafond.
Dévissez les Anneaux à douille des Douilles. Placez les A
douille sur les Douilles de façon à maintenir les Abat-jours en position. Installez l'ampoule. (Non fournie).
Produktspezifikationen
Marke: | NUVO |
Kategorie: | Lamp |
Modell: | Bridgeview 60/1703 |
Brauchst du Hilfe?
Wenn Sie Hilfe mit NUVO Bridgeview 60/1703 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten
Bedienungsanleitung Lamp NUVO
12 September 2024
12 September 2024
12 September 2024
12 September 2024
12 September 2024
12 September 2024
6 September 2024
6 September 2024
6 September 2024
6 September 2024
Bedienungsanleitung Lamp
- Lamp Samsung
- Lamp G3 Ferrari
- Lamp Tristar
- Lamp BenQ
- Lamp Gembird
- Lamp Hama
- Lamp Nedis
- Lamp Niceboy
- Lamp Philips
- Lamp Sony
- Lamp Brennenstuhl
- Lamp Cotech
- Lamp LG
- Lamp Camry
- Lamp Flex
- Lamp Thule
- Lamp OK
- Lamp Velleman
- Lamp Powerfix
- Lamp Eminent
- Lamp IKEA
- Lamp Schwaiger
- Lamp Alecto
- Lamp Beurer
- Lamp Denver
- Lamp EMOS
- Lamp Medisana
- Lamp Blaupunkt
- Lamp Black Diamond
- Lamp Rocktrail
- Lamp Einhell
- Lamp Pyle
- Lamp BeamZ
- Lamp Stairville
- Lamp Abus
- Lamp Elro
- Lamp Smartwares
- Lamp Hikoki
- Lamp Livoo
- Lamp Hazet
- Lamp Steinel
- Lamp Güde
- Lamp Livarno
- Lamp Workzone
- Lamp Goobay
- Lamp AccuLux
- Lamp Ansmann
- Lamp American DJ
- Lamp Lupine
- Lamp Nitecore
- Lamp Petzl
- Lamp Honeywell
- Lamp Dedra
- Lamp Karma
- Lamp Silverline
- Lamp Florabest
- Lamp Hansa
- Lamp Logik
- Lamp Adj
- Lamp Runtastic
- Lamp Zuiver
- Lamp Brandson
- Lamp Thermaltake
- Lamp Eurolite
- Lamp Topeak
- Lamp Milwaukee
- Lamp Toolcraft
- Lamp Eglo
- Lamp Unilux
- Lamp In-Lite
- Lamp Lucide
- Lamp Maxim
- Lamp Näve
- Lamp Osram
- Lamp Paulmann
- Lamp Steinhauer
- Lamp XQ-Lite
- Lamp V-TAC
- Lamp Melinera
- Lamp Genie
- Lamp Royal Sovereign
- Lamp Innoliving
- Lamp Sylvania
- Lamp Craftsman
- Lamp Levenhuk
- Lamp Digitus
- Lamp Akasa
- Lamp EasyMaxx
- Lamp Ozito
- Lamp Elation
- Lamp Godox
- Lamp Cameo
- Lamp GVM
- Lamp ARRI
- Lamp Vemer
- Lamp Hähnel
- Lamp Dörr
- Lamp Oecolux
- Lamp Elgato
- Lamp Nanlite
- Lamp Duronic
- Lamp Globo
- Lamp Luxform
- Lamp Martin
- Lamp Mission
- Lamp Neewer
- Lamp Steren
- Lamp Elinchrom
- Lamp Vimar
- Lamp Ozone
- Lamp Trio Lighting
- Lamp Hatco
- Lamp Sonoff
- Lamp Olight
- Lamp Profoto
- Lamp Futurelight
- Lamp Livarno Lux
- Lamp Omnilux
- Lamp Neo
- Lamp Brilliant
- Lamp Konig & Meyer
- Lamp Werma
- Lamp Chauvet
- Lamp Ledlenser
- Lamp SLV
- Lamp Goal Zero
- Lamp Gravity
- Lamp APA
- Lamp Bolt
- Lamp Heitronic
- Lamp Sagitter
- Lamp Megatron
- Lamp Adviti
- Lamp Casalux
- Lamp Kanlux
- Lamp Meross
- Lamp Kartell
- Lamp WiZ
- Lamp Fuzzix
- Lamp Paul Neuhaus
- Lamp Impact
- Lamp Artemide
- Lamp DLG
- Lamp Polarlite
- Lamp Broncolor
- Lamp UMAGE
- Lamp Lalumi
- Lamp Graypants
- Lamp Rotolight
- Lamp Lightaccents
- Lamp SIGOR
- Lamp King Mungo
- Lamp Lowel
- Lamp Dainolite
- Lamp Kind LED
- Lamp Altman
- Lamp Setti+
- Lamp Jinbei
- Lamp XCell
- Lamp Perfect Christmans
- Lamp Xline
- Lamp ET2
- Lamp Quoizel
- Lamp Golden Lighting
- Lamp Ridem
- Lamp Fredrick Ramond
- Lamp Crystorama
- Lamp Sonneman
Neueste Bedienungsanleitung für -Kategorien-
14 September 2024
14 September 2024
14 September 2024
13 September 2024
13 September 2024
13 September 2024
12 September 2024
12 September 2024
12 September 2024
9 September 2024