AFX Boon BONP2032L30D1BK Bedienungsanleitung
Lesen Sie kostenlos die đ deutsche Bedienungsanleitung fĂŒr AFX Boon BONP2032L30D1BK (2 Seiten) in der Kategorie Lamp. Dieser Bedienungsanleitung war fĂŒr 3 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet
Seite 1/2
LED r Luminaires Indoo
Pendant Ceiling Mount
120V / 60HzAC
Page 1 of 1 R1 8060417
Model #: BONP2032L30D1BK
Model #: BONP2032L30D1WH
Limited Factory Warranty
AFX Inc. hereby warranty that this îxture is free from defects in materials and workmanship when installed and used under normal operating
conditions for a period of 5 years from date of shipment from factory. This warranty covers all component parts and extends only to replacement of
defective îxture or components; it does not cover failure due to improper installation, misuse, mishandling or damage incurred in transit.
Safety Precautions
ï· Read all safety precautions and installation instructions carefully before installing or servicing this îxture. Failure to comply with these instructions
could result in potentially fatal electric shock and/or property damage.
ï· It is recommended that a qualiîed electrician perform all wiring. This îxture must be wired in accordance with all national and local electrical codes.
ï· Do not handle any energized îxture or attempt to energize any îxture with wet hands or while standing on a wet or damp surface or in water.
ï· This îxture is designed for use in a 120VAC, 60Hz fused circuit only. This îxture is compatible with a TRIAC (forward-phase or leading-edge) / ELV
(reverse-phase or trailing- edge).
ï· To reduce the risk of electrical shock, and to assure proper operation, this îxture must be adequately grounded. To accomplish proper grounding,
there must be a separate ground wire (green) contact between this îxture and the ground connection of your main power supply panel.
ï· This îxture is intended to be used for general indoor lighting in dry or damp locations.
ï· Disclaimer
Changes or modifications not expressly approved by the party responsible for compliance could void the userâs authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules and
Canadian ICES-005 (B) / NMB-005 (B). These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment oî
and on, the user is encouraged to try to correct the interference by one or more of the following measures:
âą Reorient or relocate the receiver antenna.
âą Increase the separation between the equipment and receiver.
âą Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
âą Consult with the dealer or an experienced radio/TV technician for help.
Any modiîcations to this îxture may void the warranty and interfere with the safe operation of the luminaire.
Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference,
including interference that may cause undesired operation of the device
Assembly Instructions
Step 1 Preparing for installationâ
A. at fuse or circuit breaker box before installing or servicing any part of this îxture. Disconnect electrical power
B. Carefully remove the îxture from the carton, remove components from hardware kit.
C. Install mounting bracket (1) to the junction box (not included) using two screws to (2) secure it.
Wiring All wiring must take place inside junction box (not included) â
Caution: Make sure power is oî at fuse or circuit breaker box. Check power wires for damage or scrapes. If power
supply wires are within three inches of the LED driver, use wire suitable for at least 90°C (194°F). Most Note:
dwellings built before 1985 have supply wire rated to 60°C. Consult a qualiîed electrician to ensure correct branch
circuit conductor before installing.
Step 2 Wiring îxture â
A. Make all wire connections to appropriate wire. Secure with wire nuts (provided).
B. Connect the green wire from the îxture to the supply power source ground wire.
C. Connect the white wire from the îxture to the white (N) wire from supply power source. For none-dimming îxture.
Connect the black îxture wire to the black (L) wire from supply power source.
D. Connect the white wire from the îxture to the white (N) wire from dimming source per dimmer For TRIAC dimming.
wiring instructions. Connect the black wire from the îxture to the black (L) wire from dimmer supply power source per
dimmer wiring instructions.
E. Pull on each wire lead to make sure connections are secure. Make certain no bare wires are Do not mix wires.
exposed outside of wire connectors. Tuck all connections neatly into the junction bo x.
Step 3 Mounting fixture â
A. Adjust cord length by loosening the strain relief screws on the bottom of the canopy (4). Pull the cord through the top
of the canopy and re-tighten the screw once the îxture is at the desired height. Repeat for all strain reliefs.
B. Place îxture canopy (4) over the îxture mounting plate (1), aligning the side holes (5). Then use two screws (3) to
secure the îxture in place.
Step 4 Restore power at fuse or circuit breaker box â
Luminaires dâintĂ©rieur
Monture de luminaire suspendu
120V / 60HzAC
Page 2 of 2 R1 8060417
Model #: BONP2032L30D1BK
Model #: BONP2032L30D1WH
Garantie limitée du fabricant
AFX Lighting Inc. garantit ce luminaire contre tout vice de matĂ©riau et de fabrication lorsquâil est installĂ© correctement et utilisĂ© dans des conditions
normales pendant une pĂ©riode de 5 ans Ă compter de la date de lâachat. Cette garantie couvre tous les composants et se limite au remplacement du
luminaire dĂ©fectueux ou de ses composants; elle ne couvre pas les pannes consĂ©cutives Ă une installation non conforme, Ă une mauvaise utilisation, Ă
une mauvaise manipulation ou Ă un endommagement pendant le transport.
Précautions de sécurité
ï· Read attentivement lâensemble des instructions de sĂ©curitĂ© et dâinstallation avant dâinstaller ce luminaire ou de procĂ©der Ă son entretien. Le non
respect de ces instructions pourrait avoir pour consĂ©quence des risques mortels dâĂ©lectrocution ou endommager le produit.
ï· Il est recommandĂ© quâun technicien Ă©lectrique qualiîĂ© installe le cĂąblage. Ce luminaire doit ĂȘtre cĂąblĂ© conformĂ©ment aux exigences du Code
canadien de l'électricité, des lois provinciales sur les installations électriques et des rÚglements municipaux.
ï· Ne manipulez pas un luminaire sous tension et nâessayez pas de le mettre sous tension si vos mains sont mouillĂ©es ou si vous ĂȘtes sur une
surface mouillĂ©e ou dans lâeau.
ï· Ce luminaire est conçu pour ĂȘtre montĂ© sur un circuit 120 V c.a. 60 Hz Ă©quipĂ© d'un boĂźtier de disjoncteurs ou dâun fusible.
ï· Assurez-vous que la source dâalimentation rĂ©pond aux exigences de ce luminaire. (Lisez les Ă©tiquettes sur le boĂźtier du luminaire.)
ï· Pour rĂ©duire les risques dâĂ©lectrocution et pour assurer un fonctionnement convenable, ce luminaire doit ĂȘtre mis Ă la terre. Pour installer
convenablement la mise Ă la terre, le luminaire doit ĂȘtre reliĂ© au circuit de mise Ă la terre de votre tableau de distribution Ă l'aide dâun cĂąble distinct
(vert) ou dâun conduit mĂ©tallique flexible. Lâemplacement de la vis de mise Ă la terre est clairement indiquĂ© en vert sur le boĂźtier.
ï· Ce luminaire est destinĂ© uniquement Ă ĂȘtre utilisĂ© comme Ă©clairage dâintĂ©rieur dans un endroit sec ou device
INSTRUCTIONS DE MONTAGE
Ătape PrĂ©paration pour 1 â lâinstallation
A. Coupez lâalimentation Ă©lectrique avant de procĂ©der Ă lâinstallation ou Ă lâentretien de
tout ou partie de ce luminaire
B. Rettirez le luminaire de lâemballage. SĂ©parez les contenus des sachets de piĂšces.
C. lez la traverse (2) sur la boĂźte de jonction (non comprise) Ă l'aide de deux vis (Instal 4).
CĂąblage â Tout le cĂąblage doit ĂȘtre placĂ© Ă lâintĂ©rieur de la boĂźte de jonction.
Attention : Assurez-vous que lâalimentation est coupĂ©e au disjoncteur ou au fusible.
VĂ©riîez que les cĂąbles ne sont pas endommagĂ©s ou dĂ©chirĂ©s par endroit. Utilisez des
cĂąble dâalimentation rĂ©sistant Ă une tempĂ©rature dâau moins 90 °C (194 °F).
Remarque: La plupart des habitations construites avant 1985 sont équipées de cùbles
dâalimentation ne supportant que 60 °C. Prenez conseil auprĂšs dâun Ă©lectricien qualifiĂ©
avant lâinstallation.
Ătape 2 CĂąblageâ
A. Cet appareil ne fonctionnera pas convenablement sâil nâest pas connectĂ© Ă un circuit
Ă©lectrique mis Ă la terre. Si la mise Ă la terre n'est pas convenablement eîectuĂ©e, il
existe des risques dâĂ©lectrocution, de surchauffe, de mauvais fonctionnement et cela
peut réduire la durée de vie des ampoules.
B. Connectez les cùbles entre eux de façon appropriée. Sécurisez le cùblage en utilisant
les capuchons de connexion (fournis).
C. Connectez le fil vert du luminaire au fil vert du circuit dâalimentation.
D. Le fil blanc du luminaire doit ĂȘtre connectĂ© au fil blanc (N) de la source dâalimentation.
E. Le fil noir du luminaire doit ĂȘtre connectĂ© au fil noir (L) de la source dâalimentation.
Nâintervertissez pas les fils. Tirez sur chaque îl pour vous assurer que les
raccordements sont solides. Assurez-vous quâaucun fil nu nâest visible hors des
raccords. Repoussez bien les raccordements Ă lâintĂ©rieur de la boĂźte jonction.
Ătape Montage du luminaire 3 â
A. Installez le pavillon de recouvrement (1) sur la traverse en alignant les trous de chaque
cÎté et en y vissant deux vis (3) pour l'arrimer au plafond.
B. Ajustez la longueur de îl en retirant le pavillon de recouvrement de la traverse et en
dévissant la vis antitraction. Tirez sur le cùble autant que nécessaire et enroulez-le
dans le pavillon de recouvrement avant de îxer Ă nouveau celui-ci sur la traverse.
Remarque : cordon de 9 pi fourni
Ătape Remettre le courant au fusible ou au boĂźtier de disjoncteurs4 â.
Produktspezifikationen
Marke: | AFX |
Kategorie: | Lamp |
Modell: | Boon BONP2032L30D1BK |
Brauchst du Hilfe?
Wenn Sie Hilfe mit AFX Boon BONP2032L30D1BK benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten
Bedienungsanleitung Lamp AFX
13 Oktober 2024
13 Oktober 2024
13 Oktober 2024
13 Oktober 2024
Bedienungsanleitung Lamp
- Lamp Samsung
- Lamp G3 Ferrari
- Lamp Tristar
- Lamp BenQ
- Lamp Gembird
- Lamp Hama
- Lamp Nedis
- Lamp Niceboy
- Lamp Philips
- Lamp SilverCrest
- Lamp Sony
- Lamp Brennenstuhl
- Lamp Cotech
- Lamp LG
- Lamp Camry
- Lamp Bosch
- Lamp Flex
- Lamp Thule
- Lamp OK
- Lamp Velleman
- Lamp Powerfix
- Lamp Eminent
- Lamp IKEA
- Lamp Schwaiger
- Lamp Alecto
- Lamp Beurer
- Lamp Denver
- Lamp EMOS
- Lamp Medisana
- Lamp Ryobi
- Lamp Blaupunkt
- Lamp Black Diamond
- Lamp Rocktrail
- Lamp Hilti
- Lamp Einhell
- Lamp Pyle
- Lamp BeamZ
- Lamp Stairville
- Lamp Abus
- Lamp Elro
- Lamp Smartwares
- Lamp Hikoki
- Lamp Livoo
- Lamp Hazet
- Lamp Metabo
- Lamp Stanley
- Lamp Steinel
- Lamp GĂŒde
- Lamp Livarno
- Lamp Workzone
- Lamp Varta
- Lamp Goobay
- Lamp AccuLux
- Lamp Ansmann
- Lamp American DJ
- Lamp Lightway
- Lamp Lupine
- Lamp Nitecore
- Lamp Petzl
- Lamp Silva
- Lamp Wetelux
- Lamp Honeywell
- Lamp Dedra
- Lamp Karma
- Lamp Smart
- Lamp Silverline
- Lamp Florabest
- Lamp Kodak
- Lamp Hansa
- Lamp Logik
- Lamp Adj
- Lamp Runtastic
- Lamp Zuiver
- Lamp Brandson
- Lamp Thermaltake
- Lamp GAO
- Lamp Eurolite
- Lamp Topeak
- Lamp Milwaukee
- Lamp Toolcraft
- Lamp Eglo
- Lamp Westinghouse
- Lamp Unilux
- Lamp In-Lite
- Lamp Lucide
- Lamp Massive
- Lamp Maxim
- Lamp NĂ€ve
- Lamp Nordlux
- Lamp Osram
- Lamp Paulmann
- Lamp Steinhauer
- Lamp XQ-Lite
- Lamp V-TAC
- Lamp Melinera
- Lamp Genie
- Lamp Royal Sovereign
- Lamp Innoliving
- Lamp Sylvania
- Lamp HQ
- Lamp Craftsman
- Lamp Levenhuk
- Lamp Digitus
- Lamp IVT
- Lamp Akasa
- Lamp EasyMaxx
- Lamp Ozito
- Lamp Elation
- Lamp Godox
- Lamp Cameo
- Lamp GVM
- Lamp ARRI
- Lamp Ibiza Sound
- Lamp Vemer
- Lamp HĂ€hnel
- Lamp Dörr
- Lamp Oecolux
- Lamp Elgato
- Lamp Nanlite
- Lamp Duronic
- Lamp Globo
- Lamp Luxform
- Lamp Martin
- Lamp Media-tech
- Lamp Mission
- Lamp Neewer
- Lamp Steren
- Lamp Elinchrom
- Lamp Vimar
- Lamp Ozone
- Lamp Trio Lighting
- Lamp Hatco
- Lamp Sonoff
- Lamp Esotec
- Lamp Olight
- Lamp Profoto
- Lamp Futurelight
- Lamp Livarno Lux
- Lamp Omnilux
- Lamp Neo
- Lamp Brilliant
- Lamp Konig & Meyer
- Lamp Werma
- Lamp Aputure
- Lamp Chauvet
- Lamp Ledlenser
- Lamp SLV
- Lamp Westcott
- Lamp Goal Zero
- Lamp Gravity
- Lamp APA
- Lamp Bolt
- Lamp Angler
- Lamp Luxo
- Lamp Heitronic
- Lamp ActiveJet
- Lamp Honeycomb
- Lamp ETC
- Lamp Sagitter
- Lamp Auray
- Lamp Megatron
- Lamp Adviti
- Lamp Casalux
- Lamp Briloner
- Lamp NUVO
- Lamp NEO Tools
- Lamp Kanlux
- Lamp SecoRĂŒt
- Lamp Gewiss
- Lamp Amaran
- Lamp DPM
- Lamp NightStick
- Lamp Meross
- Lamp Kartell
- Lamp Videx
- Lamp Zafferano
- Lamp WiZ
- Lamp ArmyTek
- Lamp Fuzzix
- Lamp ATN
- Lamp Paul Neuhaus
- Lamp Impact
- Lamp Artemide
- Lamp Ozocozy
- Lamp DLG
- Lamp Polarlite
- Lamp Broncolor
- Lamp UMAGE
- Lamp Markslöjd
- Lamp Velamp
- Lamp Lalumi
- Lamp Graypants
- Lamp Rutec
- Lamp Rotolight
- Lamp Lightaccents
- Lamp SIGOR
- Lamp King Mungo
- Lamp Integral LED
- Lamp Luctra
- Lamp Lowel
- Lamp Airam
- Lamp Lirio By Philips
- Lamp Fabas Luce
- Lamp Dainolite
- Lamp Signature Design By Ashley
- Lamp Kind LED
- Lamp Altman
- Lamp Setti+
- Lamp Jinbei
- Lamp XCell
- Lamp Perfect Christmans
- Lamp Xline
- Lamp ET2
- Lamp Quoizel
- Lamp Golden Lighting
- Lamp Ridem
- Lamp Fredrick Ramond
- Lamp Crystorama
- Lamp Sonneman
Neueste Bedienungsanleitung fĂŒr -Kategorien-
12 Oktober 2024
7 Oktober 2024
7 Oktober 2024
7 Oktober 2024
4 Oktober 2024
4 Oktober 2024
4 Oktober 2024
4 Oktober 2024
4 Oktober 2024
3 Oktober 2024