AFX Evanston EVNP2532LAJUDSN Bedienungsanleitung
Lesen Sie kostenlos die đ deutsche Bedienungsanleitung fĂźr AFX Evanston EVNP2532LAJUDSN (2 Seiten) in der Kategorie Lampe. Dieser Bedienungsanleitung war fĂźr 7 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet
Seite 1/2
Indoor Luminaire
Evanston Pendant
120~277VAC / 60Hz
Page 1 of 2 8061256 R0
Model EVNP2532LAJUDSN #
Safety Precautions
ďˇ Read all safety precautions and installation instructions carefully before installing or servicing this îxture. Failure to comply with these instructions could result in
potentially fatal electric shock and/or property damage.
ďˇ It is recommended that a qualiîed electrician perform all wiring. This fixture must be wired in accordance with all national and local electrical codes.
ďˇ Do not handle any energized îxture or attempt to energize any îxture with wet hands or while standing on a wet or damp surface or in water.
ďˇ This îxture is designed for use in a 120-277VAC, 60Hz fused circuit. The îxture is compatible with Triac (forward-phase or leading edge) / ELV (reverse phase or trailing
edge) and 0-10 V dimmers. Make sure that the power source conforms to the requirements of the îxture. (See labels on the îxture housing).
ďˇ To reduce the risk of electrical shock, and to assure proper operation, this îxture must be adequately grounded. To accomplish proper grounding, there must be a
separate ground wire (green) contact between this îxture and the ground connection of your main power supply panel.
ďˇ This îxture is intended to be used for general indoor lighting in dry or damp wet locations.
ďˇ Disclaimer
Changes or modiîcations not expressly approved by the party responsible for compliance could void the userâs authority to operate the equipment. NOTE: This
equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules and Canadian ICES-005 (B) / NMB-005
(B). These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate
radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment oî and on, the user is encouraged to try to correct the interference by one or more of the following measures:
⢠Reorient or relocate the receiver antenna.
⢠Increase the separation between the equipment and receiver.
⢠Connect the equipment into an outlet on a circuit diîerent from that to which the receiver is connected.
⢠Consult with the dealer or an experienced radio/TV technician for help.
Any modiîcations to this îxture may void the warranty and interfere with the safe operation of the luminaire.
Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference
that may cause undesired operation of the device.
Assembly Instructions
1. Preparing for installation-
A. before installing or servicing any part of this îxture. Disconnect electrical power
B. Remove îxture from box. Separate contents of parts bag.
2. Fixture Assembly.
A. Attach îxture shade (1) to îxture LED pan (2) using 6 provided screws (3). Hand
tighten to make sure they are secured tightly. Do not over tighten and strip threads.
B. Choose desired height for îxture stems using any , stems of the 6â 12â & 18â
provided to achieve your preferred hang length to the top of the shade.
C. Feed îxture wiring from top of shade up through both stems that are going to be
used all the way through the Hang Straight into the canopy.
D. Starting with the bottom stem thread each stem together one at a time until the
Canopy is securely tightened to the stems.
E. Tighten the stems to the canopy at the three locations with the desired stem lengths
to get the look wanted.
3. Wiring- all wiring must take place inside junction box.
Caution: Make sure power is oî at fuse or circuit breaker box. Check power wires for any damage or scrapes. Use wire suitable for at least 90C (194F).
Note: Most dwellings built before 1985 have supply wire rated to 60C. Consult a qualiîed electrician before installing.
A. ical shock, overheating, low or no light output, and This unit will not operate properly unless connected to a âgroundedâ electrical circuit. Electr
shortened LED life can result if proper grounding is not done. Securely attach power source ground wire and îxture ground wire to green ground
screw on circular mounting bracket.
B. r NEC (National Electrical Code) requirements, cut the co Then remove the ends of the three wires for Fo rd about 7â above the canopy. 3/8â from
connection purposes.
C. . Fixture will operate normally w/o connection to any dimmers. Connect white îxture lead to white (N) wire from supply For none-dimming îxture
power source. Connect black îxture lead to black (L) wire from supply power source. Gray and purple wires are not to be used and must be
individually capped to prevent shorting.
D. Connect white îxture lead to (N) wire from dimming source per dimmer wiring instructions. Connect black îxture lead to For TRIAC dimming.
black (L) wire from dimmer supply power source. Gray and purple wires are not to be used and must be individually capped to prevent shorting.
E. . Connect gray wire from the îxture to the dimmer source gray wire. Connect purple wire from the îxture to the For (0-10V) dimming îxture
dimmer source purple wire. Connect white îxture lead to white (N) wire from supply power source. Connect black îxture lead to black (L) wire from
dimmer supply power source.
F. . Pull on each wire lead to make sure connections are secure. Make certain no bare wires are exposed outside of wire Do not mix wires
connectors. Tuck all connections neatly into junction box.
Limited Factory Warranty
AFX Inc. hereby warranty that this îxture is free from defects in materials and workmanship when installed and used under normal operating
conditions for a period of 5 years from the date of shipment from the factory. This warranty covers all component parts and extends only to
replacement of defective îxture or components: it does not cover failure due to improper installation, misuse, mishandling or damage
incurred in transit.
Indoor Luminaire
Evanston Pendant
120~277VAC / 60Hz
Page 2 of 2 8061256 R0
Model # EVNP2532LAJUDSN
4. Color Changing Temperature Adjustment, CCT (if desired).
A. Adjust the two switches on each board accordingly to the desired color temperature as seen below. All boards must be set the same way. Fixture is preset Note:
to 3500K from factory.
5. Ceiling Mounting.
A. Align mounting gem bar ) over tapped holes in the junction box (Not Included) Secure mounting cross bar to the junction box with two provided screws (5), (4 .
making sure the gem bar ) is tight up against the ceiling. (4
B. Lift îxture ) with stem and canopy ) îush up to ceiling aligning two threaded stems (7) with clearance holes in the canopy (6 (1 (6 ).
C. Secure the îxture canopy (6) îush to ceiling with the two decorative thumb nuts (8) provided.
D. Place diîuser (9) inside shade resting on bottom ring to give the înished look.
6. Restore power at the fuse or breaker box.
Limited Factory Warranty
AFX Inc. hereby warranty that this îxture is free from defects in materials and workmanship when installed and used under normal operating
conditions for a period of 5 years from the date of shipment from the factory. This warranty covers all component parts and extends only to
replacement of defective îxture or components: it does not cover failure due to improper installation, misuse, mishandling or damage
incurred in transit.
Produktspezifikationen
Marke: | AFX |
Kategorie: | Lampe |
Modell: | Evanston EVNP2532LAJUDSN |
Brauchst du Hilfe?
Wenn Sie Hilfe mit AFX Evanston EVNP2532LAJUDSN benĂśtigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten
Bedienungsanleitung Lampe AFX
13 Oktober 2024
13 Oktober 2024
13 Oktober 2024
13 Oktober 2024
Bedienungsanleitung Lampe
- Lampe Samsung
- Lampe G3 Ferrari
- Lampe Tristar
- Lampe BenQ
- Lampe Gembird
- Lampe Hama
- Lampe Nedis
- Lampe Niceboy
- Lampe Philips
- Lampe SilverCrest
- Lampe Sony
- Lampe Trust
- Lampe Brennenstuhl
- Lampe Cotech
- Lampe LG
- Lampe Camry
- Lampe Bosch
- Lampe Flex
- Lampe Thule
- Lampe Klarstein
- Lampe OK
- Lampe Velleman
- Lampe Powerfix
- Lampe Eminent
- Lampe IKEA
- Lampe Schwaiger
- Lampe Alecto
- Lampe Beurer
- Lampe Bresser
- Lampe Denver
- Lampe EMOS
- Lampe KĂśnig
- Lampe Medisana
- Lampe Ryobi
- Lampe Blaupunkt
- Lampe Black Diamond
- Lampe Rocktrail
- Lampe Hilti
- Lampe Einhell
- Lampe Pyle
- Lampe Xiaomi
- Lampe BeamZ
- Lampe Stairville
- Lampe Abus
- Lampe Avidsen
- Lampe Elro
- Lampe Smartwares
- Lampe Hikoki
- Lampe Livoo
- Lampe Hazet
- Lampe Metabo
- Lampe Stanley
- Lampe Steinel
- Lampe GĂźde
- Lampe Livarno
- Lampe Workzone
- Lampe Varta
- Lampe Goobay
- Lampe AccuLux
- Lampe Ansmann
- Lampe American DJ
- Lampe Lightway
- Lampe Lupine
- Lampe Nitecore
- Lampe Petzl
- Lampe Silva
- Lampe Wetelux
- Lampe Honeywell
- Lampe Dedra
- Lampe Karma
- Lampe Carson
- Lampe Smart
- Lampe Silverline
- Lampe Florabest
- Lampe Kodak
- Lampe Hansa
- Lampe Logik
- Lampe Adj
- Lampe Runtastic
- Lampe Zuiver
- Lampe Brandson
- Lampe Thermaltake
- Lampe GAO
- Lampe Qazqa
- Lampe Eurolite
- Lampe Topeak
- Lampe Hayward
- Lampe Milwaukee
- Lampe Toolcraft
- Lampe Eglo
- Lampe Westinghouse
- Lampe Unilux
- Lampe In-Lite
- Lampe Konstsmide
- Lampe Lucide
- Lampe Massive
- Lampe Maxim
- Lampe Näve
- Lampe Nordlux
- Lampe Osram
- Lampe Paulmann
- Lampe Ranex
- Lampe Steinhauer
- Lampe XQ-Lite
- Lampe V-TAC
- Lampe Melinera
- Lampe Genie
- Lampe Royal Sovereign
- Lampe Innoliving
- Lampe Sylvania
- Lampe HQ
- Lampe Craftsman
- Lampe Levenhuk
- Lampe Digitus
- Lampe IVT
- Lampe Akasa
- Lampe EasyMaxx
- Lampe Ozito
- Lampe Elation
- Lampe Godox
- Lampe Cameo
- Lampe GVM
- Lampe ARRI
- Lampe Ibiza Sound
- Lampe Vemer
- Lampe Hähnel
- Lampe DĂśrr
- Lampe Oecolux
- Lampe Elgato
- Lampe Nanlite
- Lampe Duronic
- Lampe Globo
- Lampe Luxform
- Lampe Martin
- Lampe Media-tech
- Lampe Mission
- Lampe Neewer
- Lampe Steren
- Lampe Elinchrom
- Lampe Vimar
- Lampe Ozone
- Lampe Trio Lighting
- Lampe Hatco
- Lampe Sonoff
- Lampe Esotec
- Lampe Olight
- Lampe Profoto
- Lampe Futurelight
- Lampe Livarno Lux
- Lampe Omnilux
- Lampe Neo
- Lampe Brilliant
- Lampe Konig & Meyer
- Lampe Werma
- Lampe Aputure
- Lampe Chauvet
- Lampe Ledlenser
- Lampe SLV
- Lampe Westcott
- Lampe Goal Zero
- Lampe Gravity
- Lampe APA
- Lampe Bolt
- Lampe Laserworld
- Lampe Angler
- Lampe Luxo
- Lampe Heitronic
- Lampe ActiveJet
- Lampe Honeycomb
- Lampe ETC
- Lampe Sagitter
- Lampe Auray
- Lampe Megatron
- Lampe Adviti
- Lampe Casalux
- Lampe Briloner
- Lampe NUVO
- Lampe NEO Tools
- Lampe Kanlux
- Lampe SecoRĂźt
- Lampe Gewiss
- Lampe Amaran
- Lampe DPM
- Lampe NightStick
- Lampe Meross
- Lampe Kartell
- Lampe Videx
- Lampe Zafferano
- Lampe WiZ
- Lampe ArmyTek
- Lampe Fuzzix
- Lampe ATN
- Lampe Paul Neuhaus
- Lampe Impact
- Lampe Artemide
- Lampe Ozocozy
- Lampe DLG
- Lampe Polarlite
- Lampe Broncolor
- Lampe UMAGE
- Lampe MarkslĂśjd
- Lampe Velamp
- Lampe Lalumi
- Lampe Graypants
- Lampe Rutec
- Lampe Rotolight
- Lampe Lightaccents
- Lampe SIGOR
- Lampe King Mungo
- Lampe Integral LED
- Lampe Luctra
- Lampe Lowel
- Lampe Airam
- Lampe Lirio By Philips
- Lampe Fabas Luce
- Lampe Dainolite
- Lampe Signature Design By Ashley
- Lampe Kind LED
- Lampe Altman
- Lampe Setti+
- Lampe Jinbei
- Lampe XCell
- Lampe Perfect Christmans
- Lampe Xline
- Lampe ET2
- Lampe Quoizel
- Lampe Golden Lighting
- Lampe Ridem
- Lampe Fredrick Ramond
- Lampe Crystorama
- Lampe Sonneman
Neueste Bedienungsanleitung fĂźr -Kategorien-
12 Oktober 2024
7 Oktober 2024
7 Oktober 2024
7 Oktober 2024
4 Oktober 2024
4 Oktober 2024
4 Oktober 2024
4 Oktober 2024
4 Oktober 2024
3 Oktober 2024