Netgear WNDR37AV Bedienungsanleitung

Netgear Router WNDR37AV

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Netgear WNDR37AV (2 Seiten) in der Kategorie Router. Dieser Bedienungsanleitung war für 51 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF

Seite 1/2

Step 1:

Connect your modem.

Step 2:

Connect your router. Step 3:

Connect your computer.

Step 6:

Configure settings.

Open a browser, such as

Internet Explorer, and enter

www.routerlogin.net

to complete the setup.

Step 5:

Power on your router.

Wait until the power LED

turns solid green.

Step 4:

Power on your modem.

Wait until your modem cycles on

(approximately 2 minutes).

Note: If you have a battery-backed modem,

press the reset button. (In some cases, you may

need to remove, then re-insert, the battery to recycle

your modem.)

CAUTION:

MAKE SURE YOUR MODEM IS

TURNED OFF OR UNPLUGGED

BEFORE STARTING THE

INSTALLATION.

DSL or Cable

Wireless Router

(back)

Modem Laptop or Desktop

Computer

Wireless Router

(front)

Package Contents:

Basic Wireless Router

WNR612

Installation Guide

Power Adapter

Ethernet Cable

Ethernet cable

(not included)

Power/Test LED

Push ‘N’ Connect Security LED

Wireless LED

Internet LED

LAN Ports 1 & 2 LED

trademarks of NETGEAR, Inc. in the United States and/or other countries. Other brand and product names

are trademarks or registered trademarks of their respective holders. Information is subject to change without

notice.

January 2010

Router Configuration

Set up internet connection

1. http://In your browser address field type

www.routerlogin.net and click . Enter

2. WelcomeWhen the screen opens, click

Next. It will detect your type of internet

connection. Follow the prompts to complete

your router Internet connection.

Set up wireless security

1. First, assign a name to your wireless

network. Choose a name (SSID) that is easy

to remember. You might want to write it

down in the area provided on the middle

panel. (Default is NETGEAR). Click . Next

2. Select the Yes option to add security then

select your security method. NETGEAR

recommends WPA-PSK [TKIP] + WPA2-PSK

[AES ].

3. Choose a Passphrase. You might want to

write it down in the area provided on the

middle panel. (Example: HomeNetwork).

Click . Next

Note: Both your network name (SSID) and

passphrase are case sensitive.

4. Review your network settings on the

summary page. You may want to print this

for your records. Click to apply all Next

settings and continue to follow instructions in

the next section.

Connect Wireless Devices to Your Router

1. Open the software that manages your wireless connections on the wireless

device that you want to connect to your router. (For example, on Windows XP, go

to , right click the wireless device Control Panel ->Network Connections

and select ).View Available Wireless Networks

2. The wireless software will scan for all wireless networks in your area. Look for

and select the network name that you chose when you set up your router.

3. If your network is secured, you will be prompted for a Passphrase or network key.

Enter the Passphrase you selected and click Connect. You are now finished with

the installation.

Note: If your wireless device supports WPS (WiFi Protected Setup)—NETGEAR

calls this method Push 'N' Connect—you might be prompted to press a WPS

button on the router instead of entering a Passphrase. If so, go to Step 4.

4. Press the WPS button on the router. It will look similar to or .

5. Within 2 minutes, follow the wireless software instructions on the wireless device

to complete the WPS process. The device will then be connected to your router.

Repeat this process to add other wireless devices.

Note: Your network name, security method and passphrase must be the same on

all wireless devices connected to your router.

Enter your wireless information here:

Wireless Network Name (SSID) ________________________________

Wireless Security Passphrase __________________________________

If you forget your Passphrase, connect a computer to the router using an

Ethernet cable and log in to and enter the http://www.routerlogin.net

default User Name ( and Password ( ). admin) password

Restore Factory Default: For some routers, you may need to reset the

device to its factory default first, then reconfigure your Passphrase. To restore

factory defaults, use a paper clip to press the recessed reset button on the back

until the Power/Test light blinks. This takes about 10 seconds. Release the

button and wait for the router to reboot. Log in with the default username is

(admin) and password (password). Note: Restoring factory defaults will erase

any customizations and you will lose any configurations saved to the device!

LED Activity

Technical Support

Thank you for selecting NETGEAR products.

After completing the setup and configuration, register your product at http://

www.NETGEAR.com/register. Registration is required before you can use our

telephone support service.

Warning: Do not install this device on top of any other electrical equipment or

install any other equipment on top of this device. Keep this device away from any

heat sources such as direct sunlight, heaters, radiators, or other A/V receivers or

devices that emit heat.

Item Description

Power /Test • Solid amber: Router is performing the power-on, self-diagnostic test.

• Solid green: The router is ready.

Push “N” Connect

Security

• Solid green: Wireless security is enabled.

• Blinking Green: WPS-capable security services can be associated with the

router within 2 minutes.

• Off: There is no WPS connection.

Wireless • Solid blue: Wireless connection is established.

• Off. The wireless interface is turned off.

Internet • Solid green: Wireless router has acquired an Internet IP address.

• Blinking green: Data is being communicated.

• Solid amber: No Internet IP address has been acquired.

• Off: There is no Ethernet cable connected to the modem.

LAN Ports If a LAN light is off, be sure the Ethernet cable is securely attached at both

ends, and that the computer is turned on.

• Solid green: Local port is connected to a 100 Mbps device.

• Blinking green: Data is being transmitted at 100 Mbps.

• Solid amber: Local port is connected to a 10 Mbps device.

• Blinking amber: Data is being transmitted at 10 Mbps.

Produktspezifikationen

Marke:	Netgear
Kategorie:	Router
Modell:	WNDR37AV
Prozessortaktfrequenz:	680 MHz
WLAN-Standards:	802.11a, 802.11b, 802.11g
Gewicht:	500 g
AC-Netzadapter:	Ja
Mitgelieferte Kabel:	LAN (RJ-45)
Produktfarbe:	Schwarz
Gleichstrom-Anschluss (DC):	Ja
Netzstandard:	IEEE 802.11a, IEEE 802.11b, IEEE 802.11g, IEEE 802.11n
Unterstützte Sicherheitsalgorithmen:	WEP, WPA-PSK, WPA2-PSK
Quality of Service (QoS) Support:	Ja
Eingebauter Ethernet-Anschluss:	Ja
Schnittstellentyp Ethernet-LAN:	Schnelles Ethernet
Zertifizierung:	CEC\nRoHS\nWEEE\nDLNA
Power over Ethernet (PoE):	Nein
Anzahl Ethernet-LAN-Anschlüsse (RJ-45):	5
Ethernet LAN Datentransferraten:	10, 100 Mbit/s
LED-Anzeigen:	Ja
Anzahl der USB-Anschlüsse:	1
Web-basiertes Management:	Ja
Kompatible Betriebssysteme:	Microsoft Windows 7, Vista, XP, 2000, Mac OS, UNIX, Linux
Abmessungen (BxTxH):	223 x 153 x 31 mm
Speicherkapazität:	64 MB
Top WLAN-Standard:	Wi-Fi 4 (802.11n)
Ethernet-WAN:	Ja
WLAN Datentransferrate (max.):	150 Mbit/s
Verkabelungstechnologie:	10/100Base-T(X)
Zustandsorientierte Paketüberprüfung (SPI):	Ja
Universal Plug and Play (UPnP):	Ja
Eingebauter Prozessor:	Ja
Flash-Speicher:	8 MB
Kompatibilität:	WNDA3100
Datenübertragungsgeschwindigkeit WLAN:	11, 54, 150 Mbit/s
xDSL-Verbindung:	Ja
Bandbreite:	2.4 GHz
Prozessor Architektur:	MIPS32
NEtzwerkadressenübersetzung (NAT):	Ja