NAV-TV PCM3-CAM NTV-KIT100 Bedienungsanleitung

NAV-TV Nicht kategorisiert PCM3-CAM NTV-KIT100

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für NAV-TV PCM3-CAM NTV-KIT100 (4 Seiten) in der Kategorie Nicht kategorisiert. Dieser Bedienungsanleitung war für 28 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/4
PCM3CAM
NTV-KIT100
Rev 2 BHM 03/18/15
NTV-DOC045
3950 NW 120th Ave Coral Springs,, FL 33432
Tel. 561-955-9770 Fax. 561-955-9760
www.nav-tv.com info@nav-tv.com
PCM3CAM-USB
Front and rear camera interface
Enables a backup camera and a secondary on the factory 2009 and Up Porsche PCM 3.0 Radios
Certain features are intended for passenger and off-road use only. User must obey
all State and Federal regulations
Make sure yo radio looks li ur ke this prior to installation
Kit Contents
1 | P a g e
Filter Harness Description and Diagram
Wire Functions Wire Colors Fig. 2 - Connection plug on Can Filter
1. CAN Hi to Vehicle.
2. CAN Lo to Vehicle
3. Chassis Ground.
4. +12V Output to Camera.
5. CAN Hi to PCM.
6. CAN Lo to PCM.
7. +12V Battery
8. +12V Output to switcher and front Flir IR camera.
1. Yellow
2. Blue
3. Black
4. White/Red
5. Yellow
6. Blue
7. Red
8. White/Blue
8 pin Molex connector
Wire side view
PCM3-CAM Module
NTV-ASY107
Plug & Play Harness
NTV-HAR111
USB Cable (Updates)
NTV-CAB009
VSW-R Harness
NTV-HAR257
VSW-R Trigger
Harness
NTV-HAR066
VSW-R Board
NTV-ASY187
V1 Switcher shown
here, this has been
replaced with the
VSW-R in 03/15
Installation Part 1
1. Insert a soft pry tool into the space between the lower black fascia
piece and the lower side of the dash and gently pry the fascia towards
the rear of the vehicle to release the mounting clips. Follow the fascia
around either clockwise or counterclockwise to release the remainder of
the mounting clips. Set aside the fascia.
2. Remove (4) t20 torx screws from the sides of the
radio and pull the radio gently out of the dash in order
to disconnect all stock cables and antenna
connectors.
3. View of rear of radio and stock radio harness.
Remove the fiber optic connector from the original
harness by gently prying up on the locking tab with a
pick tool.
4. With the fiber unplugged from the factory harness
plug the aftermarket harness into the original harness
and secure it by closing the stock locking tab. Attach
the PCM3CAM module to the aftermarket harness
and secure the filter to the back of the radio cavity with
either double sided tape or Velcro. Fold the harness in
the cavity as shown to allow clearance for the radio.
2 | P a g e
Installation Part 2
5. Drop the plastic panel over the passenger side kick panel area
by taking out (1) t20 Torx screw and pulling the panel towards
the floor. Run the black, white/blue and white/red wires from the
new radio harness into the opening as in the picture to your left.
These wires will power your reverse and front cameras, as well
as the video switcher.
6. If your vehicle is not equipped with a stock camera and you are
not installing a front camera then simply unplug the male RCA end
from the female in the aftermarket harness and run your camera’s
video RCA directly to the female plug. Connect ground for the
reverse camera to the black wire and 12 volt positive to the
white/red from step 5 and insulate the white/blue wire. Skip to step
8.
Vehicles with factory mera installation ca VSW-R
7a. Extend and plug the female RCA (radio side) of the harness into AV1
out. Extend d plug the male RCA (v an ehicle side) into AV1 in. Connect a
front camera, for example, a Flir night vision camera RCA into in. Video 2
Connect the black grou wire from stnd ep 5 to both the ground of the front
camera and the ground (black wire) from the video switcher. Connect the
12v d wire of the switcher ( re (Video 2 Trig) white/ wire) to the white/bl ue
wire . from the module
Vehicles without factory camera switcher installation
7b. Extend and plug the female RCA (radio side) of the harness into
Video Output. Plug the RCA from your aftermarket rear view ame c ra into
Video 1 put (VSW-R) in . Connect a front camera, for example, a Flir night
vision camera RCA into Video 2 in. Connect the black gro wire from und
the switcher to the ground nd the from the switcher, the reverse camera a
front camera. ect the Conn white/re wire to the 12v wired to your
aftermarket back up camera. Connect the lu e the e white/b e wir to 12v wir
on ont sion camera your fr vi
8. Plug the fiber optic cable you unplugged in step 3 into the aftermarket
harness. Reconnect all the antenna, power and all other connectors back
into the radio and slide the radio back into the dash. Reassemble in the
reverse order as steps 1,2 and 5. Now you are ready to proceed to the
programming and operations section. Good job!
3 | P a g e


Produktspezifikationen

Marke: NAV-TV
Kategorie: Nicht kategorisiert
Modell: PCM3-CAM NTV-KIT100

Brauchst du Hilfe?

Wenn Sie Hilfe mit NAV-TV PCM3-CAM NTV-KIT100 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Nicht kategorisiert NAV-TV

Bedienungsanleitung Nicht kategorisiert

Neueste Bedienungsanleitung für -Kategorien-