NAV-TV NTV-KIT483 Bedienungsanleitung
Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für NAV-TV NTV-KIT483 (4 Seiten) in der Kategorie Dashcam. Dieser Bedienungsanleitung war für 39 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet
Seite 1/4
BHM
09/28/15
NTV-DOC 154
rB4
Agreement End user agrees to use this product in compliance with all State and Federal laws. NAV-TV Corp. would not be held liable for misuse of its product. :
If you do not agree, please discontinue use immediately and return product to place of purchase. This product is intended for off-road use and passenger
entertainment only.
1 | P a g e
3950 NW 120th Ave, Coral Springs, FL 33 TEL 561-955-9770 FAX 561-955-9760 065
www.nav-tv.com info@nav-tv.com
MB Sprinter-CAM
NTV-KIT477
Overview
The MB Sprinter-CAM allows the user to add an aî…³ermarket rear camera to the factory screen on the
Mercedes Sprinter. If desired, forced camera is an opon through a mounted toggle switch (not included).
ATTENTION: This module locks the VIN and can only be used on ONE vehicle at a me. to
Kit Contents
Plug & Play T Harness
NTV-HAR 081
SMB to RCA Adapter
NTV-CAB007
USB Cable (updates)
NTV-CAB009
MB Sprinter-CAM
Module
NTV-ASY171
CAN-XG Adapter
NTV-HAR058
BHM
09/28/15
NTV-DOC 154
rB4
Agreement End user agrees to use this product in compliance with all State and Federal laws. NAV-TV Corp. would not be held liable for misuse of its product. :
If you do not agree, please discontinue use immediately and return product to place of purchase. This product is intended for off-road use and passenger
entertainment only.
2 | P a g e
Module Pin Outs
PIN #
Descripon
Color
1
12v Constant (+)
Yellow
2
Input 1 (de-program wire)
Red
3
Input 2 (program wire)
Blue
4
Input 3 (Force CAM)
Pink
8
CAN HI (Radio Side)
White/Green
9
CAN HI (Car Side)
Brown/Black
10
Ground (-)
Black
17
CAN LO (Radio Side)
Green
18
CAN LO (Car Side)
Brown
Installaon
1. Remove the factory radio. This requires pulling panels and removing screws. Disconnect all connected
harnesses and set the radio aside.
2. Connect the male end of the factory 44-pin plug to the female end of the provided Plug & Play T-
Harness.
3. Disconnect the two smaller plugs on the factory 44-pin plug and connect
them both to the male end of the provided Plug & Play T-Harness.
4. Connect the harness to the 8-pin plug located in the center of the CAN-XG Adapter Plug & Play T-
Harness.
5. Connect the to the 18-pin Molex MB Sprinter-CAM module
connector on the end of the . CAN-XG Adapter
Wire Side
BHM
09/28/15
NTV-DOC 154
rB4
Agreement End user agrees to use this product in compliance with all State and Federal laws. NAV-TV Corp. would not be held liable for misuse of its product. :
If you do not agree, please discontinue use immediately and return product to place of purchase. This product is intended for off-road use and passenger
entertainment only.
3 | P a g e
6. Connect the provided to the green port on the back of the SMB to RCA Adapter
Sprinter’s factory radio (if there is already a plug at the green port, disconnect it and
use the provided SMB cable instead).
7. Aî…´er installing and running the reverse camera to the dash
opening (connect power to an ACC source, NOT reverse!),
connect the camera’s signal lead to the RCA side of the SMB
to RCA Adapter Note: ACC power in Mercedes can oî…¯en be .
found at the cigaree lighter.
8. Connect the male end of the provided 44-pin Plug & Play T-
Harness leave the module outside of the dash, or accessible. back to the radio and
9. Proceed to .Programming (below)
10. Once programming is complete, start the vehicle and place it into
reverse. The reverse camera’s image should appear on the screen
automacally.
11. Oponal: If forced camera is desired, connect one side of a toggle
switch (not included) to ACC, and the other side to INPUT 3 (pink).
Acvang this switch will force the rear camera in any gear (reverse
camera must be powered with ACC and a reverse wire!) not
Module Programming
1. Begin by installing this kit (page 2, steps 1-9).
2. From the 18-pin Molex connector, î…–nd the labeled Blue wire Input 2.
3. Cut the metal connector oî…“ of the and strip the end back. blue wire
4. Connect this wire to 12v (+). temporarily When programming is complete, you must remove this wire
from power! Note: the yellow wire on the white 8-PIN molex connector is CAN wire, not constant a
power Use the RED wire in this plug (constant 12v) or the yellow wire from 18-PIN XG module. .
5. Turn (not ACC or running, but the vehicle’s ignion ON ON).
6. Wait at least for the radio to fully boot and sele. 1 minute
7. With connected to 12v (+), and Input 2 toggle (pull and release once) the high-beam head lamp lever
‘DIAGNOSIS’ will appear on the screen. Refer to the chart below during programming.
8. Once the radio has been programmed, it will shut down (not reboot, but turn oî…“).
9. Aer a few seconds, press the on the radio to bring the radio back up. power buon
10. Remove Input 2 from 12v (+). Insulate the wire end.
11. Connue with installaon: step 10.
Produktspezifikationen
| Marke: | NAV-TV |
| Kategorie: | Dashcam |
| Modell: | NTV-KIT483 |
Brauchst du Hilfe?
Wenn Sie Hilfe mit NAV-TV NTV-KIT483 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten
Bedienungsanleitung Dashcam NAV-TV
11 Juli 2024
30 April 2023
30 April 2023
30 April 2023
30 April 2023
30 April 2023
30 April 2023
30 April 2023
30 April 2023
30 April 2023
Bedienungsanleitung Dashcam
- Dashcam Gembird
- Dashcam Genius
- Dashcam Hama
- Dashcam HP
- Dashcam Nedis
- Dashcam Niceboy
- Dashcam Philips
- Dashcam AEG
- Dashcam Dymond
- Dashcam Maginon
- Dashcam Technaxx
- Dashcam Denver
- Dashcam König
- Dashcam Trevi
- Dashcam Blaupunkt
- Dashcam Kenwood
- Dashcam Trebs
- Dashcam Dometic
- Dashcam Pyle
- Dashcam Salora
- Dashcam Aiptek
- Dashcam Caliber
- Dashcam Pioneer
- Dashcam JVC
- Dashcam Motorola
- Dashcam Xiaomi
- Dashcam Elro
- Dashcam Ferguson
- Dashcam Garmin
- Dashcam GOCLEVER
- Dashcam Lamax
- Dashcam Mio
- Dashcam Sencor
- Dashcam Waeco
- Dashcam Scosche
- Dashcam XOMAX
- Dashcam Guardo
- Dashcam Midland
- Dashcam Alpine
- Dashcam Minolta
- Dashcam Rollei
- Dashcam EUFAB
- Dashcam Pro User
- Dashcam Toyota
- Dashcam ADATA
- Dashcam Overmax
- Dashcam Monacor
- Dashcam Ednet
- Dashcam Osram
- Dashcam NextBase
- Dashcam Uniden
- Dashcam Clarion
- Dashcam Kogan
- Dashcam Jobo
- Dashcam Skytronic
- Dashcam Audiovox
- Dashcam Navitel
- Dashcam Navman
- Dashcam Cobra
- Dashcam CamOne
- Dashcam EVOLVEO
- Dashcam TrueCam
- Dashcam ION
- Dashcam DNT
- Dashcam Swann
- Dashcam Xblitz
- Dashcam Prestigio
- Dashcam Tracer
- Dashcam Boss
- Dashcam Mini
- Dashcam Hertz
- Dashcam Hikvision
- Dashcam Jensen
- Dashcam Transcend
- Dashcam DOD
- Dashcam Innovv
- Dashcam IRoad
- Dashcam Laser
- Dashcam Lidl
- Dashcam Media-tech
- Dashcam Naxa
- Dashcam Nordval
- Dashcam Roadeyes
- Dashcam Steren
- Dashcam Thinkware
- Dashcam Veho
- Dashcam Metra
- Dashcam ModeCom
- Dashcam CRUX
- Dashcam Escort
- Dashcam Brigmton
- Dashcam Kaiser Baas
- Dashcam KJB Security Products
- Dashcam BlackVue
- Dashcam Valueline
- Dashcam Braun Phototechnik
- Dashcam BLOW
- Dashcam Boyo
- Dashcam Cowon
- Dashcam Rexing
- Dashcam Dashmate
- Dashcam EchoMaster
- Dashcam AZDome
- Dashcam Carmera
- Dashcam VIOFO
- Dashcam Mobileye
- Dashcam Kapture
- Dashcam ProUser
- Dashcam Nanocam+
- Dashcam Vicovation
- Dashcam Andatech
- Dashcam RIPOON
Neueste Bedienungsanleitung für -Kategorien-
16 Oktober 2024
15 Oktober 2024
9 Oktober 2024
4 Oktober 2024
3 Oktober 2024
30 September 2024
27 September 2024
27 September 2024
24 September 2024
22 September 2024