Michigan Raptor 1000 Bedienungsanleitung

Michigan Nicht kategorisiert Raptor 1000

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Michigan Raptor 1000 (23 Seiten) in der Kategorie Nicht kategorisiert. Dieser Bedienungsanleitung war für 35 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF

Seite 1/23

User Manual

[Revision 2 ].0 May 2022

READ THIS MANUAL CAREFULLY BEFORE USE – FAILURE TO DO SO MAY RESULT IN INJURY, PROPERTY DAMAGE AND MAY

VOID WARRANTY. • KEEP THIS MANUAL FOR FUTURE REFERENCE. • Products covered by this manual may vary in appearance,

assembly, inclusions, specifications, description, and packaging.

The product is NOT supplied with engine oil, although traces of oil from the manufacturing process may be present. It is essential to add

adequate engine oil of the correct type to the engine before use. Failure to add engine oil will void the product warranty.

Raptor 1000 Wood Chipper & Shredder

E&OE © 2 2022 Michigan USA

Safety

Safety messages are designed to alert you to possible dangers or hazards that could cause death, injury or

equipment or property damage if not understood or followed. Safety messages have the following symbols:

You WILL be KILLED or

SERIOUSLY INJURED if you do

not follow instructions.

You CAN be KILLED or

SERIOUSLY INJURED if you do

not follow instructions.

You CAN be INJURED if you do

not follow instructions or equipment

damage may occur.

It is vital that you read and understand this

user manual before using the product,

including safety warnings, and any assembly

and operating instructions. Keep the manual

for future reference.

Safety precautions and recommendations

detailed here must be fully understood and

followed to reduce the risk of injury, fire,

explosion, electrical hazard, and/or property

damage.

Safety information presented here is generic

in nature some advice may not be –

applicable to every product. The term

"equipment" refers to the product, be it

electrical mains powered, battery powered or

combustion engine powered.

• - Before Use If you are not familiar with the

safe operation/handling of the equipment or

are in any way unsure of any aspect of

suitability or correct use for your

application, you should complete training

conducted by a person or organization

qualified in safe use and operation of this

equipment, including fuel/electrical handling

and safety.

• Do NOT operate the equipment in

flammable or explosive environments, such

as in the presence of flammable liquids,

gases or dust. The equipment may create

sparks or heat that may ignite flammable

substances.

• Keep clear of moving parts.

• Equipment may be a potential source of

electric shock or injury if misused.

• Do NOT operate the equipment if it is

damaged, malfunctioning or is in an

excessively worn state.

• Do NOT allow others to use the equipment

unless they have read this manual and are

adequately trained.

• - risk Keep packaging away from children

of suffocation! Operators must use the

equipment correctly. When using the

equipment, consider conditions and pay

due care to persons and property.

General Work Area Safety

• Work areas should be clean and well it.

• Do not operate the equipment if

bystanders, animals etc are within

operating range of the equipment or the

general work area.

• If devices are provided for connecting dust

extraction / collection facilities, ensure

these are connected and used properly.

Dust collection can reduce dust-related

hazards.

General Personal Safety

• Wear appropriate protective equipment

when operating, servicing, or when in the

operating area of the equipment to help

protect from eye and ear injury, poisoning,

burns, cutting and crush injuries. Protective

equipment such as safety goggles,

respirators, non slip safety footwear, hard -

hat, hearing protection etc should be used

for appropriate equipment / conditions.

Other people nearby should also wear

appropriate personal protective equipment.

Do not wear loose clothing or jewellery,

which can be caught in moving parts. Keep

hair and clothing away from the equipment.

• Stay alert and use common sense when

operating the equipment. Do not over-

reach. Always maintain secure footing and

balance.

• Do not use the equipment if tired or under

the influence of drugs, alcohol or

medication.

• This equipment is not intended for use by

persons with reduced physical, sensory or

mental capabilities.

General Fuel Safety

• Petrol/fuel/gasoline is extremely flammable

– keep clear of naked flames or other

ignition sources.

• Do not spill fuel. If you spill fuel, wipe it off

the equipment immediately if fuel gets on –

your clothing, change clothing.

• Do NOT smoke near fuel or when

refuelling.

• Always shut off the engine before

refuelling.

• Do NOT refuel a hot engine.

• Open the fuel cap carefully to allow any

pressure build up in the tank to release -

slowly.

• Always refuel in well ventilated areas.

• Always check for fuel leakage. If fuel

leakage is found, do not start or run the

engine until all leaks are fixed.

General Carbon Monoxide Safety-

• Using a combustion engine indoors CAN

KILL IN MINUTES. Engine exhaust

contains carbon a poison you -monoxide –

cannot smell or see.

• Use combustion engines OUTSIDE only,

and far away from windows, doors and

vents.

Chipper Use and Care

• The equipment should be operated by

responsible adults only, 18 years of age

and over.

• The equipment must be used on firm, flat

and level surfaces only.

• Maintain a safe working distance of at

least 15m (36') between the output chute

and any persons, animals or structures.

• Before each use, check the cutting blade

clearance and ensure that blade

fasteners are tight.

• Do not use the equipment for purposes it

is not designed for.

• Do not attempt to chip or shred branches

bigger then 120mm diameter.

• Branches greater than 30mm diameter

that are growing out of a branch being

chipped should be cut off and chipped

separately.

• For roots, always remove any attached

dirt, stones etc before chipping.

• Do not attempt to chip or shred any

material other than suitable wood types.

• Do not attempt to remove materials from

the machine or attempt to un-jam it while

the machine is running.

• Do not use the machine in confined

areas where ventilation or space around

the machine is limited.

• After stopping the engine, always allow

all moving components (blades etc) to

stop moving before moving, lifting etc.

General Fuel Safety

• Petrol/fuel/gasoline is

extremely flammable – keep clear

of naked flames or other ignition

sources.

• Do not spill fuel. If you spill fuel, wipe it

from equipment immediately – if fuel

gets on your clothing, change them

immediately

• Do not smoke near fuel.

• Always shut off the engine before

refuelling.

• Do not refuel a hot engine.

• Open the fuel cap carefully to allow any

pressure build up in the tank to release -

slowly.

• Always refuel in well ventilated areas.

• Always check for fuel leakage. If fuel

leakage is found, do not start or run the

engine until all leaks are fixed.

Raptor 1000 Wood Chipper & Shredder

E&OE © 3 2022 Michigan USA

General Electrical Safety

• Inspect electrical equipment, extension

cords, power bars, and electrical fittings for

damage or wear before each use. Repair or

replace damaged equipment immediately.

• Ensure all power sources conform to

equipment voltage requirements and are

disconnected before connecting or

disconnecting equipment.

• When wiring electrically powered

equipment, follow all electrical and safety

codes.

• Wherever possible, use a residual current

device (RCD).

• High voltage / high current power lines may

be present. Use extreme caution to avoid

contact or interference with power lines.

Electrical shock can be fatal.

General Electrical Safety

• Electrically grounded equipment must have

an approved cord and plug and be

connected to a grounded electrical outlet.

• Do NOT bypass the ON/OFF switch and

operate equipment by connecting and

disconnecting the electrical cord.

• Do NOT use equipment that has exposed

wiring, damaged switches, covers or

guards.

• Do NOT use electrical equipment in wet

conditions or in damp locations.

• Do NOT use electrical cords to lift, move or

carry equipment.

• Do NOT coil or knot electrical cords, and

ensure electrical cords are not trip hazards.

General Service Information

• The equipment must be serviced or

repaired at authorised service centres by

qualified personnel only.

• Replacement parts must be original

equipment manufacturer (OEM) to ensure

equipment safety is maintained.

• Do NOT attempt any maintenance or repair

work not described in this manual.

• After use, the equipment and components

may still be hot allow the equipment to –

cool and disconnect spark plugs and/or

electrical power sources and/or batteries

from it before , changing adjusting

accessories or performing repair or

maintenance.

• Do NOT adjust while the equipment is

running.

• Perform service related activities in suitable

conditions, such as a workshop.

• Replace worn, damaged or missing

warning/safety labels immediately.

Wood Chipper & Shredder General Safety

This machine is designed solely to chip wood and must not be used for any other purpose. It should only be used by trained operators who are

familiar with the content of this manual. It is potentially hazardous to fit or use any parts other than your dealer parts. The supplier disclaims all

liability for the consequences of such use, which in addition voids the machine warranty.

• Operating this Wood Chipper safely is necessary to prevent or minimize the risk of death or serious injury. Unsafe operation can create a number

of hazards for you. Always take the following precautions when operating:

• Your Wood Chipper is a powerful tool, not a plaything. Exercise extreme caution at all times. The machine is designed to Chip Woods. Do not

use it for any other purpose.

• Know how to stop the Wood Chipper quickly.

• Never operate your unit on a slippery, wet, muddy, or icy surface. Exercise caution to avoid slipping or falling.

• See manufacturer's instructions for proper operation and installation of accessories.

• Never use the machine without ensuring that all guards and shields are in place.

• Never, under any conditions, remove, bend, cut, fit, weld, or otherwise alter standard parts on the Wood Chipper. This includes all shields and

guards. Modifications to your machine could cause personal injuries and property damage and will invalid your warranty.

• If the machine start to make an unusual noise or vibrate, shut down the engine, disconnect the spark plug wire, keeping it away from the spark

plug to prevent accidental starting, wait 5 minutes for engine to cool down, then inspect for damage. Vibration is generally a warning of trouble.

Check damaged parts and clean, repair and/or replace as necessary.

• Never tamper with safety devices. Check their proper operation regularly.

• Before performing any maintenance or inspection procedure, shut down the engine, disconnect the spark plug wire keeping it away from the

spark plug to prevent accidental starting, wait 5 minutes for machine to cool down.

• Never allow people who are unfamiliar with these instructions to use the Wood Chipper. Allow only responsible individuals who are familiar with

these rules of safe operation to use your machine.

• Never overload or attempt to chip woods beyond the manufacturer's recommendation. It could result in personal injury or damage to the machine.

• While using, don't hurry or take things for granted. When in doubt about the equipment or your surroundings stop the machine and take time to

look things over.

• Never operate the machine when under the influence of alcohol, drugs, or medication.

• Use the machine only in daylight.

• Stay alert for hidden hazards or traffic.

• Keep all nuts and bolts tight and keep the equipment in good operating condition.

List of warnings and cautions cannot be all-inclusive. If situations occur that are not covered by this manual, the operator must apply

common sense and operate this wood chipper in a safe manner. Contact local dealers for assistance in your area.

Before Using the Wood Chipper

• Operators must be fully trained before using this machine.

• User Manual is read and understood.

• Machine is positioned on level ground, all guards are fitted and in good condition.

• Blades are in good condition and secure. All blades are sharpened or replaced in sets.

• All fasteners are checked for tightness.

• Only WOODEN materials free of nails etc. are fed into the machine.

• Fire extinguisher is available on site.

Produktspezifikationen

Marke:	Michigan
Kategorie:	Nicht kategorisiert
Modell:	Raptor 1000

Brauchst du Hilfe?

Wenn Sie Hilfe mit Michigan Raptor 1000 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten

Ihren Namen*

Deine E-Mail*

Schreiben Sie hier Ihre Frage

Bedienungsanleitung Nicht kategorisiert Michigan

Michigan SY0.5 Bedienungsanleitung

6 September 2024

Michigan Raptor 1000 Bedienungsanleitung

20 August 2024

Michigan Raptor 950 Bedienungsanleitung

20 August 2024

Michigan Ravenger 1950 Bedienungsanleitung

22 März 2024

Michigan Raptor 900 Bedienungsanleitung

13 Februar 2024

Michigan GDTSRDMC3C0A Bedienungsanleitung

23 Dezember 2023

Bedienungsanleitung Nicht kategorisiert

Neueste Bedienungsanleitung für -Kategorien-

DAS Audio AX-112-5 Bedienungsanleitung

16 Oktober 2024

Ferplast Ergocomfort Freetime Bedienungsanleitung

16 Oktober 2024

AEG MECK52 Bedienungsanleitung

16 Oktober 2024

Makita UR012G Bedienungsanleitung

16 Oktober 2024

Stihl HT 70 Bedienungsanleitung

16 Oktober 2024

Ernesto H14270 Bedienungsanleitung

16 Oktober 2024

IFM AC901S Bedienungsanleitung

16 Oktober 2024

Nedis RFPOM120FBK Bedienungsanleitung

16 Oktober 2024

AEG E9KLCS01 Bedienungsanleitung

16 Oktober 2024

ART ProChannel II Bedienungsanleitung

16 Oktober 2024