Metra 99-9229G Bedienungsanleitung


Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Metra 99-9229G (4 Seiten) in der Kategorie Nicht kategorisiert. Dieser Bedienungsanleitung war für 9 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/4
METRA. The World’s best kits.metraonline.com © COPYRIGHT 2004-2015 METRA ELECTRONICS CORPORATION
REV. 9/10/2015 INST99-9229G
Installation instructions for part 99-9229G
CAUTION!
Metra recommends disconnecting the negative bat
-
tery terminal before beginning any installation, unless the vehicle
manufacturer recommends against so. Please check with your local
Dealership for more information. All accessories, switches, climate
controls panels, and especially air bag indicator lights must be con-
nected before reconnecting the battery or cycling the ignition. Also,
do not remove the factory radio with the key in the on position, or the
vehicle running. It would be best to remove the key from the ignition
and then wait a few seconds before removing the factory radio.
ISO DIN radio provision with pocket
ISO DDIN radio provision
Painted to match factory finish
A) Radio trim panel • B) Radio housing C) Pocket • D) (4) #8 x 3/8” Phillips screws E) (4) Panel clips
KIT FEATURES
KIT COMPONENTS
WIRING & ANTENNA CONNECTIONS (sold separately)
Wiring Harness: 70-9221
Antenna Adapter:40-VL10
Panel removal tool • Phillips screwdriver T-25 Torx driver
TOOLS REQUIRED
Volvo S60/V70 2001-2004
99-9229G
A B C
Dash Disassembly ................................................. 2
Kit Assembly
ISO DIN radio provision with pocket ...................... 3
ISO DDIN radio provision ...................................... 3
Table of Contents
D E
99-9229G
2
1. Remove the panel between the
climate control and gear selector.
(Figure A)
2. Move the gear selector as far back
as possible, unsnap the panel
surrounding it, and then rotate it
45 degrees either way. (Figure B)
3. Remove (2) T-25 screws now
exposed securing the climate
control panel to the vehicle, and
then remove. (Figure C)
Continue to 3 a.
Dash Disassembly
a. Angle the panel outwards so
that it is possible to insert a
couple of fingers between the
center console and the side of
the panel. (Figure D)
b. Remove the panel by pulling
it downward, maintaining the
same angle. Some force is
required because the panel is
tightly installed. (Figure D)
c. Do not unplug the connectors.
Place the panel to one side instead
.
4. Remove (2) T-25 Torx screws
securing the radio, and then
remove. (Figure E)
5. Remove the sub-dash bracket from
the radio, and then remove.
a. Remove (5) T-25 Torx screws
securing the bracket. (Figure F)
b. Depress the snaps on the top
and bottom of the pocket.
(Figure G)
Continue to kit assembly
(Figure B) (Figure E)
(Figure A)
(Figure C) (Figure F)
(Figure D) (Figure G)
99-9229G
Kit Assembly
ISO DIN radio provision with pocket
1. Secure the pocket radio to the
housing using (4) #8 x 3/8” Phillips
screws provided. (Figure A)
Note: Rounded edge of pocket
faces towards the bottom.
2. Remove the metal DIN sleeve and
trim ring from the aftermarket radio.
3. Slide the radio into the completed
assembly, and then secure it to the
assembly using screws supplied
with the radio. (Figure A)
4.
Locate the factory wiring harness and
antenna connector in the dash, and
complete all necessary connections to the
radio. Metra recommends using the proper
mating adapter from Metra and/or AXXESS.
Re-connect the negative battery terminal
and test the radio for proper operation.
5. Reassemble the dash in reverse
order of disassembly.
6. Attach (4) panel clips supplied to
the , and then snap radio trim panel
the panel over the radio.
ISO Double DIN radio provision
1. Slide the radio into the radio
housing and secure it using screws
supplied with the radio.
(Figure A)
2. Locate the factory wiring harness
and antenna connector in the
dash, and complete all necessary
connections to the radio. Metra
recommends using the proper
mating adapter from Metra and/or
AXXESS. Re-connect the negative
battery terminal and test the radio
for proper operation.
3. Reassemble the dash in reverse
order of disassembly.
4. Attach (4) panel clips supplied to
the , and then snap radio trim panel
the panel over the radio.
3
(Figure A) (Figure A)


Produktspezifikationen

Marke: Metra
Kategorie: Nicht kategorisiert
Modell: 99-9229G

Brauchst du Hilfe?

Wenn Sie Hilfe mit Metra 99-9229G benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Nicht kategorisiert Metra

Bedienungsanleitung Nicht kategorisiert

Neueste Bedienungsanleitung für -Kategorien-