Metra 99-7877 Bedienungsanleitung


Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Metra 99-7877 (7 Seiten) in der Kategorie Nicht kategorisiert. Dieser Bedienungsanleitung war für 30 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/7
METRA. The World’s best kits.metraonline.com © COPYRIGHT 2004-2016 METRA ELECTRONICS CORPORATION
REV. 3/9/2016 INST99-7877
Installation instructions for part 99-7877
CAUTION!
All accessories, switches, climate controls panels, and
especially air bag indicator lights must be connected before cycling
the ignition. Also, do not remove the factory radio with the key in the
on position, or while the vehicle is running.
DIN radio provision with pocket
ISO DIN radio provision with pocket
ISO DDIN radio provision
Painted to match factory dash
99-7877S = Silver, 99-7877B = Matte Black
A) Radio housing • B) ISO brackets • C) ISO trim plate • D) ISO DDIN brackets • E) ISO DDIN trim plate • F) Pocket
20;-,(;<9,:
20;*64765,5;:
>0905.(5;,55(*655,*;065: (sold separately)
Wiring Harness:70-1729
Antenna Adapter: • 40-HD10 • 40-HD11 (with NAV)
Panel removal tool Phillips screwdriver • 8mm Socket wrench
;663:9,8<09,+
Honda Fit 2009-2013
99-7877 Dash Disassembly ..................................................2
Kit Preparation ........................................................3
Kit Assembly
DIN radio provision with pocket ............................ 4
ISO DIN radio provision with pocket ...................... 5
ISO DDIN radio provision ...................................... 6
Table of Contents
A B FEDC
99-7877
2
Dash Disassembly
1. Unclip and remove the lower
center panel below radio. (Figure A)
2. Remove (1) 8mm bolt facing up
behind center panel.
Slide the recirculation 5V[L!
control lever to FRESH for better
access to bolt. (Figure A)
3. Open the upper glove box then use
a pry tool to unclip and remove the
radio/climate control assembly.
(Figure B & C)
(Figure A)
(Figure B)
(Figure C)
4. Remove (2) Phillips screws
securing the hazard switch
to the back of the factory
radio panel. (Figure D)
5. Remove (2) Phillips screws
securing the air bag light to
the back of the factory radio
panel. (Figure E)
6. Remove (5) Phillips screws
securing the A/C vents to
the radio panel.
7. Remove (7) retaining clips
from radio housing to be
used later in kit preparation.
Continue to kit preparation
(Figure D)
(Figure E)
Rear factory radio panel
Rear factory radio panel
99-7877
Kit Preparation
3
(Figure A) (Figure B)
1. Secure the hazard switch into the
radio housing panel using the
factory hardware. (Figure A)
2. Secure the air bag light into the
radio housing panel using the
factory hardware. (Figure A)
3. Secure the A/C vents to the
radio housing using the factory
hardware. (Figure B)
4. Attach the (7) retaining clips to the
radio housing panel in the same
location as removed from the
factory radio panel.


Produktspezifikationen

Marke: Metra
Kategorie: Nicht kategorisiert
Modell: 99-7877

Brauchst du Hilfe?

Wenn Sie Hilfe mit Metra 99-7877 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Nicht kategorisiert Metra

Bedienungsanleitung Nicht kategorisiert

Neueste Bedienungsanleitung für -Kategorien-