MB Quart MBQX-STG2-RAD-1 Bedienungsanleitung

MB Quart Nicht kategorisiert MBQX-STG2-RAD-1

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für MB Quart MBQX-STG2-RAD-1 (51 Seiten) in der Kategorie Nicht kategorisiert. Dieser Bedienungsanleitung war für 5 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/51
CAN-AM MAVERICK X3
STAGE 2 / 400 WATT / TWO SPEAKER
UTV-TUNED AUDIO PACKAGE
Installation Manual
MBQX-STG2-RAD-1
3
PRE-INSTALLATION
INSTALLATION TIME
About 2.5 hours are required to complete this installation (assuming unmodied vehicle).
TOOLS AND SUPPLIES NEEDED
● Wire Strippers and Crimpers ● Phillips Screwdriver
● Flush Cut Wire Cutters (for trimming zip ties) ● Small, Straight (Jeweler’s) Screwdriver
● High-Quality Electrical Tape ● Heat Gun or Lighter
● Hand-Held Battery-Powered Drill, 9/64” & 1/8” Drill Bits ● Bojo Tools (Non-Marring Pry Tools)
● Ratchet, 8mm Socket ● 10mm Socket (Gauge Cluster/Battery)
● 13mm Socket and 13mm Box Wrench (Seat Removal) ● 18mm Socket (Seat Removal)
● 1/2” Socket (Subwoofer Enclosure Front Brackets) ● 7/16” Socket (Optional 3rd Amp Plate)
● T-25 and T-27 Torx Drivers (Dash & Housing Hardware) ● T-30 Torx Driver (Dash/Console)
Depending on which vehicle-specic UTV-tuned audio system you are installing, you may or may not need
all of the tools listed above. You may also own more specialized tools to complete the installation. Share the
pics of your installation on our social media channels to help others.
In addition to the tools listed, have music ready for INITIAL TESTING and FINE TUNING steps.
● USB thumb drive with music pre-loaded
● Bluetooth device such as a smartphone with music or a music app
SAFETY PRECAUTIONS
Safely prepare your vehicle for the installation before proceeding.
● Turn the ignition off and remove the key
● Use a packing blanket other soft material to protect your machine
● Safety Glasses - always wear eye protection
● Once all of the seats are removed, disconnect the negative battery cable before proceeding
PREPARATION FOR INSTALLATION & DISASSEMBLY
Before fully dismantling your vehicle, we suggest you prepare all your components, enclosures and wiring
harnesses. It increases efciency to have everything ready when each component is installed. Please note
some models with seat belts will require seat belt attachment point removal to remove the whole seat.
REMOVE SEATS - DISCONNECT BATTERY
123
Slide driver’s seat forward
and remove two 18mm bolts
securing the rear of the seat
frame. If the vehicle has
factory-installed seats, you
can also access these bolts by
ipping up the seat cushion (a
socket extension is required).
Slide driver’s seat back to
access front 13mm through-
bolts and nuts. Using a socket
and box wrench, remove inner
and outer front seat hardware.
Unplug seat belt sensor.
Remove front driver’s seat and
set aside with all hardware.
Repeat seat removal on
front passenger’s side (and
rear seats - if present). Once
passenger seat near battery is
removed, disconnect (black)
negative battery cable by
removing a 10mm bolt and set
the negative cable aside.


Produktspezifikationen

Marke: MB Quart
Kategorie: Nicht kategorisiert
Modell: MBQX-STG2-RAD-1

Brauchst du Hilfe?

Wenn Sie Hilfe mit MB Quart MBQX-STG2-RAD-1 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Nicht kategorisiert MB Quart

Bedienungsanleitung Nicht kategorisiert

Neueste Bedienungsanleitung für -Kategorien-