Manhattan 207683 Bedienungsanleitung


Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Manhattan 207683 (16 Seiten) in der Kategorie Nicht kategorisiert. Dieser Bedienungsanleitung war für 4 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/16
Scan to
register your
product warranty
For additional benets:
or go to: register.manhattanproducts.com/r/207683
1080p HDMI
KVM Over
IP Extender
Instructions
Model 207683
Important: Read before use. • Importante: Leer antes de usar.
2
RXTX
HDMI
USB
UTP Cable
IR TX
IR RX
USB
USBHDMI
TX
HDMI
USB
UTP Cable
IR TX
IR RX
RX
USBUSBHDMI
RX
USBUSBHDMI
RX
USBUSBHDMI
UTP Cable UTP Cable UTP Cable
. . . . . . .
Simple Mode
Allocation Mode
The Manhattan 1080p HDMI KVM over
IP Extender Kit lets you access any
computer (or other HDMI source) from
a keyboard, mouse and display up to
120 m (394 ft.) away. You can either
make a direct connection through a
single RJ45 Ethernet cable (Cat6 or
higher recommended for maximum
range and performance) or you connect
it to a switch in your existing network
to overcome distance limitations (see
Mode diagrams for sample setups).
The kit includes mounting brackets and
screws to install the units on a wall or
ceiling. First, use the screws to fasten the
brackets to the units; then use the screws
to fasten the units to the wall or ceiling.
For specifications, visit
manhattanproducts.com.
Register this product at register.
manhattanproducts.com/r/207683
or scan the QR code on the cover.
Instructions
English
3
11 1 2 3 4 5 6 12
11 2 7 8 9 10 6 12
RECEIVER
TRANSMITTER
Instructions
English
1 HDMI IN: Connect input source.
2 )HDMI OUT (both units : Connect
output display/projector at
sender side for loop out and at
receiver side for remote out.
3 USB/PC: Connect to computer
source to control it through
Receiver’s USB ports.
4 Power LED: lights when power is
connected;
USB: lights when connected
to a computer.
5 IR TX: Connect IR Transmitter (TX) to
send IR remote signal to source; place
it in line of sight to source sensor.
6 LAN TX / LAN RX: Use Cat6 cable to
connect to units to each other or to a
switch, depending on desired setup
(green LED: lit = power, off =
no power; yellow LED: slow
flashing = no video signal; fast
flashing = video signal).
7 USB: In Allocation Mode, press to
control source at selected receiver.
8 Connect USB keyboard and mouse.
9 POWER LED: lights when power is
connected;
Keyboard LED: lights when
connected to keyboard;
Mouse LED: lights when
connected to mouse.
10 IR RX: Connect IR Receiver
(RX) to receive IR remote signal
at display location; place it in
line of sight to remote.
11 DC 5V (both units): Connect
included power adapters.
12 RESET (both units): Press
to perform a restart.


Produktspezifikationen

Marke: Manhattan
Kategorie: Nicht kategorisiert
Modell: 207683

Brauchst du Hilfe?

Wenn Sie Hilfe mit Manhattan 207683 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Nicht kategorisiert Manhattan

Bedienungsanleitung Nicht kategorisiert

Neueste Bedienungsanleitung für -Kategorien-