Lorex ECP-2601R Bedienungsanleitung

Lorex Nicht kategorisiert ECP-2601R

Lesen Sie kostenlos die ๐Ÿ“– deutsche Bedienungsanleitung fรผr Lorex ECP-2601R (2 Seiten) in der Kategorie Nicht kategorisiert. Dieser Bedienungsanleitung war fรผr 11 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF
Seite 1/2
Package
ECP-2601T (Transmitter)
ECP-2601R (Receiver)
Bracket Quick Start
Guide
Hardware Overview
Right
Left
57V DC
Bracket
NO ANALOG
CAMERA
ETHERNET
PoE-ON
Data-Link
Join-Link
Power
PoE
Bracket
Join
ON OFF
RJ45
PoE-ON (ECP-2601T)
PD-AUX (ECP-2601R)
Bracket Hole DC Power Jack
Bracket Hole Join Button
Status LED Indicator
PoE ON/OFF Switch
(ECP-2601T only)
Overview
This device is a High-Speed, long distance Ethernet & PoE extender
that makes possible to transmit the Ethernet signal up to 2.4Km and
PoE up to 1.2Km via Coax (or UTP, 2-wire) cables in different situations.
It is cost-effective and time saving solution to migrate existing analog
system to IP based system since this device supports easy installation
utilizing the existing cable.
With long distance transmission feature, the device makes to
overcome 100 meters distance limitation easily and reduces the
construction cost significantly compared with fiber optic configuration.
Features
๎šEthernet over Coax communication following IEEE1901 Standard
๎šData + Power over Coax cable (or UTP, 2-Wire)
๎šData distance up to 2.4Km
๎šPoE distance up to 1.2Km
๎šMax. 95Mbps Bandwidth
(270Mbps between Intercoax 2 series models)
๎š10/100 Full Duplex
๎š128bit AES network encryption
๎šSupports Multi-connection (Daisy chain, Star, etc.)
๎šPoE, PoE+, Extra PoE (Max. 60W output)
๎šSupports UTP, Telephone (2 Pairs), 2-Wire cable communication
(Using BTE Series)
๎šLED Indication (Data, Power, Link, PoE)
๎šPlug & Play
๎šSurge Protection
๎šSupport PoE+ Input (25.5W) from PSE devices โ€“ ECP-2601R Only
๎šSlim design
Quick Start Guide
ECP-2601T / ECP-2601R
Please read carefully the instruction manual before use.
Contents of this manual are subject to change without prior
notice for reasons such as functionality enhancements.
LED Indicators
Indicator Color Function
PoE-ON (Tx) ON : PoE Switch On (PoE Output)
OFF : PoE Switch Off
PD-AUX (Rx) ON : PoE Input or Powered by Transmitter
OFF : Powered by adapter
Data-Link Blinking : Ethernet Data Act
Join-Link ECP-Product Link
Power 57V DC Link
Installation Guide
1. Set the IP address on the camera following the instruction manual
of the camera.
รŽ
If the camera IP is automatically assigned (DHCP, etc.), there is no
need to set the camera IP separately.
2. Connect BNC of the coaxial cable to each Transmitter/Receiver.
3. Connect 57V DC power to Transmitter/Receiver first and then to
AC outlet.
รŽ
Receiver can be powered by PoE Switch Device (PoE+ PD
Supported) but for safe working, it recommeded to use 57V DC
Power supply on Receiver. When using both PoE switch Device and
power supply at the same time, power supply works preferentially.
รŽ
In case of 7W camera, the device supports long distance PoE
transmission up to 1,200m over RG6 coaxial cable. PoE transmission
distance can be varied depending on cable type and Cameraโ€™s power
consumption(W).
4. When they are connected without any problem, Power / Join Link
LED are on.
5. Adhere the brackets in the package to Transmitter/Receiver and
then fix up the products.
6. Connect the UTP(LAN) cable between Receiver and NVR first and
then between Transmitter and camera.
7. Turn on the PoE switch on Transmitter for PoE IP camera and if the
camera is powered by a separate power source (not powered by
PoE output feature of the Transmitter
), turn off the PoE switch on
Transmitter.
รŽ
Both Transmitter/Receiver send data and power together via BNC
connector. Receiver does not have PoE support so that it can send
data only via RJ45.
8. Ping test is recommended to confirm the whole network after
installation.
9. Check the video signal on the monitor.
Rev.1.1
Caution
๎šPlease install the device following the installation guide.
๎šDo not touch the device and cable with wet hands.
๎šKeep away from moisture and shock.
๎šDo not install near any heat sources such as radiators, heat registers,
stoves or other apparatus that produce heat.
๎šIndoor use only.
๎šDo not use for other purposes.
๎šDo not disassemble or modify this device.
๎šDo not put any sticker or paint on it.
๎šIf this device is defective or malfunctioning, please unplug the power
adapter immediately and contact dealer or service center.
๎šPlease use the rated power supply for the product.
๎šConnect DC power to this device first and then to AC outlet.
Warranty
๎šThis device has passed the quality control and product inspection.
๎šPlease install and use according to the installation guide.
๎šThe warranty period for this product is 24 months from the date of
purchase.
๎šIf this device is defective or malfunctioning, please unplug the power
adapter immediately and contact dealer or service center.
๎šAny damages or breakage from userโ€™s abuse, accident, modification
or natural disasters will not be covered manufacturerโ€™s warranty.
How to change the communication password
(Coax/UTP/2-Wire)
All Intercoax EoC converters have the same password as factory
defaults setting value and can be used immediately when connecting
to the product (Plug & Play mode).
However, if a number of products are mixed in the same area or
the signal transmission line is in poor condition, the communication
passwords for each equipment (or group) can be set differently to
prevent cross-talk between the lines.
1. Needed items for Joining
EoC Converters / Power supply / Short Cable (Coax, UTP, 2-Wire) /
Paper clip
2. Product configuration
a. Connect EoC Converters with Coax cable (or UTP, 2-Wire) and
power to the one of the converters up with power supply.
b. Check if the Power LED on both devices is ON.
3. Remove the existing password (Unjoining)
This process removes passwords that are entered as factory
defaults.
a. Press the Join button on one of the connected products using a
paper clip until the Power LED turns off and on (Approximately
15 seconds)
b. Remove the existing password by pressing the Join button on the
opposite product in the same way as above.
c. Join LED will be turned off if the password on the devices is
removed correctly.
4. Create New Password (Joining)
New password for communication between connected devices is
created and this will block the communication with other devices (or
group) which have a different password.
a. Press the Join button for 2 seconds on one of the connected
product using a paper clip and the Join LED of the device will
flicker at a constant speed. (Stand-by mode)
b. Press the Join button for 2 seconds on the opposite device in the
same way as above. And then, the Join LED of the device flickers
at a constant speed and both devices restart at the same time.
c. Then the Join-Link lights up and communications are resumed
between the products
5. When adding new products in 1:N configuration to a group that
has already been joined. (Group Joining)
a. Connect new device to the group which is already joined. (using
T-BNC or Y-UTP coupler, Terminal block)
b. Remove the password of the new device in the same way as step
โ€˜3-aโ€™.
c. Press Join button on the one of the device of the existing group
for 2 seconds and Join LED flickers at a constant speed.
d. Press Join button on the new device for 2 seconds and new
device restarts
e. Join-Link lights up and communications are resumed between
the products.
Please visit below website for more detailed information.
Web: http://www.intercoax.com Tel: +82. 31. 365. 3133~4
E-mail: info@intercoax.com Fax: +82. 31. 365. 3135
This device complies with part 15 of the fcc rules. Operation is subject to the
following two conditions :
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received including interference
that may cause undesired operation
Applications
AC/DC
Adapter(12V)
Non-PoE IP
Camera
Coaxial Cable
Coaxial Cable
10/100 Ethernet
10/100 Ethernet
PoE
ECP-2601R
57V DC/1.2A
Power Supply
NVR
ECP-2601T ECP-2601R
ECP-2601T
PoE
Camera
PoE Switch
Specification
Model ECP-2601T ECP-2601R
Interface
Coax 1 x 75ฮฉ BNC (Female)
- Ethernet over Coax (B-LinX)
Ethernet 1 x RJ45 - 10/100 Base-T
with Auto-detect MDIX
Transmission Rate 95Mbps Full Duplex
(270Mbps between Intercoax devices)
Transmission
Distance
Ethernet up to 2.4Km(RG-6)
PoE (PoC) up to 1.2Km (RG-6 / 7W camera)
LED
Indication
Ethernet 1 x Data-Link (Yellow)
EoC 1 x Join-Link (Green)
Power 1 x Power On(Amber)
PoE 1 x PoE Out (Red)
Encryption 128-bit AES
Power
Input B-Linx or
DC12V~57V
PoE Switch or
DC12V~57V
PoE Output
IEEE802.3af(PoE),
IEEE802.3at (PoE+),
Extra PoE up to 60W
PoE Not Supported
PoC Only
Mechanical Dimension 82.4(L) x 61.6(W) x 24(H)mm
Weight 77g
Environment
Operating Temp -20 ~ 60ยฐC
Storage Temp -30 ~ 80ยฐC
Relative Humidity 10% ~ 90%
Compliance Certification FCC, CE, KC, RoHS
Surge Protection IEC 61000-4-5 4kV(1.2 / 50us), 2kA(8 / 20us)
Optional Accessories 57VDC / 1.2A External Power Supply
ยฉ Intercoax Co., Ltd.

Produktspezifikationen

Marke: Lorex
Kategorie: Nicht kategorisiert
Modell: ECP-2601R

Brauchst du Hilfe?

Wenn Sie Hilfe mit Lorex ECP-2601R benรถtigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten


Bedienungsanleitung Nicht kategorisiert Lorex

Lorex

Lorex AJLD-1B Bedienungsanleitung

28 September 2024
Lorex

Lorex AX8 Bedienungsanleitung

5 September 2024
Lorex

Lorex AEX16 Bedienungsanleitung

5 September 2024
Lorex

Lorex AJLZ-1W Bedienungsanleitung

5 September 2024
Lorex

Lorex ECP-01T Bedienungsanleitung

3 September 2024
Lorex

Lorex ECP-01R Bedienungsanleitung

3 September 2024
Lorex

Lorex ETP-01 Bedienungsanleitung

3 September 2024
Lorex

Lorex ETP-01T Bedienungsanleitung

3 September 2024
Lorex

Lorex EPR-111 Bedienungsanleitung

3 September 2024
Lorex

Lorex ECP-2601R Bedienungsanleitung

3 September 2024

Bedienungsanleitung Nicht kategorisiert

Neueste Bedienungsanleitung fรผr -Kategorien-

DAS Audio

DAS Audio AX-112-5 Bedienungsanleitung

16 Oktober 2024
Ferplast

Ferplast Ergocomfort Freetime Bedienungsanleitung

16 Oktober 2024
AEG

AEG MECK52 Bedienungsanleitung

16 Oktober 2024
Makita

Makita UR012G Bedienungsanleitung

16 Oktober 2024
Stihl

Stihl HT 70 Bedienungsanleitung

16 Oktober 2024
Ernesto

Ernesto H14270 Bedienungsanleitung

16 Oktober 2024
IFM

IFM AC901S Bedienungsanleitung

16 Oktober 2024
Nedis

Nedis RFPOM120FBK Bedienungsanleitung

16 Oktober 2024
AEG

AEG E9KLCS01 Bedienungsanleitung

16 Oktober 2024
ART

ART ProChannel II Bedienungsanleitung

16 Oktober 2024